CrimeStopper CoolStart RS800 Series II User manual

RS800 Series II
Remote Engine Starting System
OPERATING INSTRUCTIONS
CONGRATULATIONSonyourchoice ofa CoolStart™ Remote Engine Starter by Crimestopper Security Products
Inc. This booklet contains the information necessary for using & maintaining your remote start system. If any
questions arise, contact your installation dealer or Crimestopper Security Products Inc. at [phone].
OPERATION CAUTIONS & WARNINGS
CRIMESTOPPER SECURITY PRODUCTS, INC. and its VENDORS shall not be liable for any accident resulting from the use of this
equipment. This system is designed to be professionally installed onto a vehicle in which all items, such as parking brake and all
associated components, door switches, transmission shift linkage, throttle linkage, and all engine safety features, are in perfect
working condition.
DO NOT install this Remote Engine Starting System on MANUAL TRANSMISSION vehicles. If accidentally left in gear the
vehicle could become a self-propelled threat to life and property.
IT IS ABSOLUTELY THE OWNER’S SOLE RESPONSIBILITY TO: A) Understand the operation of this system and its safety
features. B) Check for proper operation of these safety features prior to accepting delivery of the vehicle from the installation facility.
C) Check and maintain the condition of the vehicle and all items relative to the proper operation of this system and its safety features.
D) Always leave the doors and windows closed and locked to protect against accident and theft.
DO NOT remote start the vehicle in a closed garage. Make sure that the garage door is open or there is adequate ventilation.
Failure to observe this rule could result in injury or death from poisonous Carbon Monoxide fumes.
IT IS ABSOLUTELY THE OWNERS SOLE RESPONSIBILITY TO: make certain the vehicle PARKING BRAKE is properly adjusted
and will hold the vehicle securely in all parking conditions, and to periodically check and maintain proper adjustment.
REV. A 09.10.01
This device complies with FCC Rules part 15. Operation is
subject to the following two
conditions: 1) This device may not cause interference, and (2) this device must accept
any interference that may be received, including interference that may cause
undesired operation. The manufacturer is not responsible for
any radio or TV
interference caused by unauthorized modification to this equipment. Such modification
could void the user's authority to operate the equipment.

OPERATING THE REMOTE TRANSMITTER
The transmitter supplied with this RS800 system has (2) buttons / channels.
#1 #2
START
LOCK/ REMOTE
START
UNLOCK
C RIME S TOPPER
REMOTE ENGINE CONTROL
REMOTE ENGINE STARTING -SUCCESSFUL START:
1) Press and release the remote start button.
2) Parking lights flash once, then turn ON along with the IGN/ACC circuits
3) After 6 seconds Starter Motor engages. (Parking lights and Acc circuits turn off while cranking.)
4) Engine Starts and Runs. Parking Lights and Acc turn back on, Doors Lock.
5) Enginewill remainrunning forprogrammed runtime or untilresetwith Brakepedal. Ifneeded,the enginecanbe
turned off with remote transmitter or for RS801 model, activating the Green Start input wire again.
AFTER
IGN
6
STARTER
THEN
FLASH 1X
SOLID
SOLID
SEC.
START
NOTE:
When using the optional
Starter Disable feature without
power door locks, be certain to
install the supplied L.E.D. which
will be your only
indication that
the Starter Disable is active. You
must press the UNLOCK button on
the transmitter if the L.E.D. is
flashing or the vehicle will not
start.

REMOTE ENGINE CONTROL
REMOTE ENGINE STARTING -UNSUCCESSFUL START
In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then
attempts to restart the engine a 2nd and 3rd time. Forhard starting engines,the unit willallow astarter crank timeof
upto13 secondsmaximum. This shouldprovide amplecrankingtime fordifficult starts,butis limitedto13 seconds
to help prevent damage to the starter from over cranking in the case of a malfunctioning unit.
1) If engine starts on 2nd or 3rd attempt, see steps 4 & 5 above of "Successful Start".
2) If Third attempt fails to start engine, the system will turn off and doors will remain locked. NO FURTHER
ATTEMPTS WILL BE MADE AUTOMATICALLY
TURNING OFF A REMOTE STARTED ENGINE:
1) Engine is running in Remote Start (Parking lights are ON).
2) Press and release the Remote Start button again.
3) Engine turns & parking lights OFF, Doors remain locked or will re-lock/re-arm if applicable.
CONVENIENCE AND SAFETY FEATURES
KEYLESS ENTRY (POWER DOOR LOCK CONTROL)
Thissystem enablesyou toremotely lockand unlockthe vehicle’s doors (if equipped with power locks) through the
transmitter for safety and convenience. This feature may require extra labor and/or parts to install.
REMOTE LOCK / UNLOCK
Press the Lock/Unlock button on the transmitter as you leave or come near the vehicle. Parking lights will flash
once for lock and twice for unlock. If vehicle is remote started, engine will remain running and lights will flash but
return to solid indicating engine is still being controlled by the remote starter.
NOTES: Doors lock automatically when vehicle is Remote Started. Starter Disable/Anti-grind is also
enabled/disabledwith thelock/unlock button. Ifan anti-grind/starterkill relayis installedon a vehiclewithout power
door locks, the lock/unlock button of the remote control must still be used to operate the Starter disable.
VALET MODE / STARTER DISABLE OVERRIDE
Before servicing your vehicle or handing the keys over to a Valet we recommend putting the unit into valet mode.
The remote start function WILL NOT operate when in Valet mode. To enter Valet mode, turn the key to the ON
position, press and hold Program/Valet switch for 6 seconds. The LED will turn on solid and the system is now in
valet. Performthis procedureagain toexit ofValet mode. Thekeyless entrywillstill functionnormally whileinvalet
mode. In the event of a lost or broken transmitter, perform this step to override the Starter Disable (If installed).

CONVENIENCE AND SAFETY FEATURES
HOOD OPEN SAFETY SWITCH
Prevents the engine being Remote Started when hood is open and will abort a remote start if running. Eliminates
risk of injury to someone working under the hood of the vehicle. If a remote start is requested with the hood open,
the lights will flash twice, Ignition will not turn on, and the unit will not attempt a start.
BRAKE PEDAL RESET CIRCUITRY
Preventsstarting orshuts off aremote startedvehicle whenthiscircuit isactive oractivated. Preventsunauthorized
tampering. Thiscircuit shutsthe systemdown immediatelywhen brake pedal is pressed if key is not in ignition and
turned to the run position.
ANTI-GRIND / STARTER DISABLE
Prevents the driver from accidentally grinding the starter if the Ignition key is turned too far (to the start position)
while engine is already running from the remote starter. Starter circuit is automatically disabled when doors are
locked using the remote as an added security feature.
NOTE:
Inthe eventof amajor malfunction,performing electricalservice orjumpstarting thevehicle youshould removethe
main Power Fuse(s) to protect the unit from possible damage.
TRANSMITTER PROGRAMMING
TRANSMITTER PROGRAMMING:
Note: All transmitter codes must be learned at time of programming!! The RS800 allows storage of up to 4
different transmitter codes.
1. Open Hood (Ground Gray hood pin wire if no hood pin is installed).
2. Turn key to the ON position.
3. Press Programming button 4 times. After a few seconds, the unit will flash the parking lights 4 times.
4. Press button #1 of the transmitter to be coded. You should get 2 light flashes indicating the unit is waiting for a
2nd code, then press button #1 of a second transmitter, the unit will flash 3 times indicating its waiting for the 3rd
codeand 4flashes forthe 4th code. Ifall 4codes arelearned, theunit willautomatically exitcodelearning mode,
otherwise turn key off and close hood.
CRIMESTOPPER SECURITY PRODUCTS, INC. 1770 SOUTH TAPO ST. SIMI VALLEY, CA. 93063