CRL LD813 User manual
Visit us at for international toll free information 1
© COPYRIGHT C.R. LAURENCE CO., INC. 2012
Subject to printing errors and design changes over which we have no contro . In the event of prob ems p ease contact our Customer Service Department.
AVD3064_09/12
AC.R. LAURENCE Co., INC.
3.6V Cordless Screwdriver
Read this material before using this roduct.
Failure to do so can result in serious injury.
SAVE THIS MANUAL
Care for the environment!
Tool must not be discarded with household waste!
This roduct contains electrical or electronic com onents that should be
recycled. Leave the roduct for recycling at the designated station e.g.
the local authority's recycling station.
Visit us at for international toll free information 2
A
/17/41/6.2!&%371%!$3()2-!.4!,#!1%&4,,7"%&/1%42).'3(%3//,!),41%3/&/,,/6
!,,).2314#3)/.2"%,/6-!71%24,3).%,%#31)#2(/#+&)1%!.$/12%1)/420%12/.!,).*417
1. Insert the bit into the chuck until it snaps into place.
2. tart the tool by squeezing the trigger switch. LED work lights will turn on when trigger
switch is activated.
3. Forward/Reverse switch, located above trigger switch, is marked with forward and reverse arrows.
#1%6$1)5%1$/%2./36/1+
• Press the LED battery level indicator and make sure that the unit is fully charged.
!).3%.!.#%
• Use only mild soap and a damp cloth to clean the tool.
• Do not allow any liquids to get inside the tool.
• Do not immerse any part of the tool in liquids.
)23/,1)5%1
Voltage……………………………..…..................3.6 Volts (DC)
Torque…………………………............................3 N.m
peed (no load)………………………………...…150RPM
$!03/1
Input……….............110 Volts (AC)/60Hz
Output……….......... 5 Volts (DC)/300mA
Charging Time……. 5 to 7 hours (max.10 hours)
1. To prevent accidents, keep your work area clean and well lit.
$!03/1
Input……….............220-240 Volts (AC)/60Hz
Output……….......... 5 Volts (DC)/300mA
Charging Time……. 5 to 7 hours (max.10 hours)
Visit us at for international toll free information 3
A
2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gasses or dust. Power tools create sparks which could ignite dust or fumes.
3. Keep bystanders, children and visitors away while operating a power tool. Distractions can
cause you to lose control.
1. To prevent damage to the power cable, never carry the tool by the cable and keep the cable
away from heat, oil, sharp edges, or moving parts. hould the power cable be damaged,
replace it immediately to prevent the risk of fire.
2. The battery must only be recharged with the included charger. A charger that may be suitable
for one type of battery may create a risk of fire when used with another battery.
1. tay alert and use extreme caution when operating a power tool. Do not use any tool while tired
or under the influence of drugs, alcohol or medication. A moment of carelessness while operating
power tools may result in serious personal injury.
2. To reduce the risk of injury, never wear loose fitting clothing or jewelry when operating the tool
and keep your hands away from the moving parts. If you have long hair keep it tied back.
3. To avoid accidental start up, make sure the safety switch is in the locked position before inserting
the battery.
4. To maintain full control of the tool, do not overreach and keep your weight evenly balanced
over both feet.
5. Always use suitable safety equipment including eye protection, dust mask, non-slip safety shoes,
and ear protection.
1. Tool service must be performed by qualified personnel. ervice or maintenance performed
by an unqualified person could result in a risk of injury.
2. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may
result in electric shock or injury.
3. Do not touch moving parts. Allow the power tool accessories (bits and blades, etc.) to cool before
touching them. They can become extremely hot during use and can burn your skin.
4. Always wear protective safety glasses when operating power tools and a face mask when
the environment is dusty.
)23/,1)5%1
1. nap Chuck
2. Worklight
3. LED Battery Indicator Lights
4. LED Battery Level Indicator Button
5. Forward/Reverse witch
##%22/1)%2
6. AC Adaptor/Charger
Visit us at for international toll free information 4
A
1. Place the tool on a clean dry surface within 3 feet (1 m) of an outlet.
2. Plug AC Adaptor into the charging port located on the back of the unit.
3. Allow 5 to 7 hours for the battery to fully charge.
4. When the battery has fully charged, disconnect the charger from the power supply.
5. The LED battery level indicator tells you the amount of charge that you have on the battery.
6. When all three lights (RED, YELLOW and GREEN) are illuminated, the battery is functioning at
full capacity.
7. When two lights (YELLOW and RED) are illuminated, this indicates that the battery capacity
is beginning to diminish.
8. When only one light (RED) is illuminated, this indicates that the battery capacity is low and
the unit needs to be charged.
This manual suits for next models
2
Table of contents
Other CRL Power Screwdriver manuals
Popular Power Screwdriver manuals by other brands
BLACKCUBE
BLACKCUBE XW-2001 instruction manual
Pattfield Ergo Tools
Pattfield Ergo Tools E-AS 10,8 V Li operating instructions
Perles
Perles HB 6142-14LT operating instructions
Universal Tool
Universal Tool UT8963ATT-11 General Safety Information & Replacement Parts
VONROC
VONROC S CD501DC Original instructions
Sealey
Sealey CP4VSD instructions
