CROW WORKS QUINCY Series User manual

QUINCY BANQUETTE HARDWARE LIST
24”, 30” & 48” BANQUETTE HARDWARE LIST 60” & 72” BANQUETTE HARDWARE LIST
TOOLS NEEDED UPHOLSTERED PANEL HARDWARE LIST
(48) #8x1” Round Washer Head Screws
(2) 5/16-18 x 1” Bolt + 5/16-18 Nut (Hex Flange)
(1) 3/4” Spacer Board
(2) 9-1/2”W Back Boards
(2) 7-1/2”W Seat Boards
(2) Seat Brackets
(72) #8x1” Round Washer Head Screws
(3) 5/16-18 x 1” Bolt + 5/16-18 Nut (Hex Flange)
(1) 3/4” Spacer Board
(2) 9-1/2”W Back Boards
(2) 7-1/2”W Seat Boards
(3) Seat Brackets
Tape Measure
Drill
#2 Square Head Bit
2- ½” Open End Wrench
(2) Flat Washers
(2) Thumb Screws
DESIGNED AND BUILT IN MIDDLE AMERICA®CROWWORKS.COM
Questions? contact us at [email protected].
UPHOLSTERED PANEL FOR
SEAT AND/OR BACK
DRAWN BY:
DESCRIPTION:
All ideas, designs, planning, drawings, and specifications are owned by, and are the property of Crow Works, and were created and developed for use on, and in connection with the specified project. Under no condition is this drawing or any part of, to be reproduced, used by or disclosed to any person, firm, or corp. without the written consent of Crow Works.
QBH-30
30" QUINCY BOOTH
SHEET NO:
2 OF 4
2
A
SIZE:
1:12
SCALE:
0
REV:
PART NO:
DATE:
DATE:
66.37 LBS
CHECKED BY:
WEIGHT:

STEP 1
Place brackets on the floor center-to-center using
measurements below.
24”W Banquette: 18-1/2” (2 brackets)
30”W Banquette: 24-1/2” (2 brackets)
48”W Banquette: 42-1/2” (2 brackets)
60”W Banquette: 27-1/4” (3 brackets)
72”W Banquette: 33-1/4” (3 brackets)
STEP 2
See diagram to the right for spacing of the
back and seat boards.
STEP 3
Place boards on the brackets, with the 9-1/2” boards on the
back and the 7-1/2” boards on the seat, as shown in Step 2.
Secure the remaining boards on the brackets with screws
using the ¾” wide spacer to keep each board in the proper
location while attaching them.
Once all boards are placed on the bracket, screw each board
to the brackets using the holes in the metal bracket plates
using the proper torque setting for your drill.
3/4" 3/4"
7-1/2"
3/4"
9-1/2"
1/2
"
A
B B
A
2X “A”
2X “B”
STEP 4
See optional instructions if cushions were ordered for the
banquette or if banquette will be double-sided. If not,
ensure the banquette is in the correct position and secure
it to the floor using hardware suited to the floor substrate.
Secure to the floor through the holes in the foot plate. Each
foot plate needs at least one fastener.
Please note, Crow Works only provides hardware for the
assembly of the banquette and not to fix the product to the
floor. Please use an appropriate fastener for your application.
The foot plate is 1/4” thick and has (2X) 3/8” holes for
securing to the floor.
FOOT PLATE
DESIGNED AND BUILT IN MIDDLE AMERICA®CROWWORKS.COM
Questions? contact us at [email protected].
QUINCY BANQUETTE
ASSEMBLY INSTRUCTIONS
66.37 LBS
CHECKED BY:
DRAWN BY:
DESCRIPTION:
All ideas, designs, planning, drawings, and specifications are owned by, and are the property of Crow Works, and were created and developed for use on, and in connection with the specified project. Under no condition is this drawing or any part of, to be reproduced, used by or disclosed to any person, firm, or corp. without the written consent of Crow Works.
QBH-30
30" QUINCY BOOTH
SHEET NO:
1 OF 4
1
A
SIZE:
1:12
SCALE:
0
REV:
PART NO:
DATE:
DATE:
WEIGHT:
REVISIONS
REV. DESCRIPTION DATE APPROVED
A
Start with bottom back board

STEP A
Set upholstered panel wood spine into the
slot between the two boards and center the
cushion on the booth.
STEP B
To secure cushions, place a flat washer around
the predrilled hole in the wood spine. Then,
use a thumb screw to secure the washer and
cushion into place. Repeat for all predrilled
holes in all cushions.
FLAT WASHER
THUMB SCREW
FOR DOUBLE-SIDED BOOTH
Secure booths to each other using (2) hex flange
bolts and nuts.
QUINCY BANQUETTE
ASSEMBLY INSTRUCTIONS (OPTIONAL)
3/4" 3/4"
7-1/2"
3/4"
9-1/2"
1/2
"
A
B B
A
3/4" 3/4"
7-1/2"
3/4"
9-1/2"
1/2
"
A
B B
A
ADDING UPHOLSTERED PANELS
DESIGNED AND BUILT IN MIDDLE AMERICA®CROWWORKS.COM
Questions? contact us at [email protected].