Croydex Boston WS010122 User manual

1
Boston Vanity Unit
Thank you for purchasing this Croydex product. Please follow the xing and care instructions to ensure
your vanity unit is tted safely and retains its high quality nish.
Please retain this leaet for future reference.
This installation guide applies to the following vanity unit:
WS010122 - Boston Vanity Unit
Tools required - not supplied
Pencil;Tape Measure; Philips Screwdriver; Flat Head Screwdriver; Mallet; Drill; 5mm Drill Bit;
8mm Drill Bit (Ceramic drill bit optional).
KEEP DIY TOOLS OUT OF THE REACH OF CHILDREN
Home Safety Advice
- It is recommended that two people t this product to ensure that it is tted safely.
- Always take care when using power tools, particularly in the bathroom.
- Always check for hidden cables and pipework before drilling and take extreme care if there is any
water in the working area.
- It is advisable to use a residual current circuit breaker (RCCB).
- Always wear suitable eye protection when drilling.
- If the product is to be tted on a ceramic tiled wall, a ceramic drill bit should be used.
- Always ensure that the drill hole passes through the central tiled area rather than through the grouted
area. To prevent damage to the tile, mask the area around the hole with tape before drilling.
- Do not strike the product with hard or sharp objects.
Product Care
To retain the best quality nish, clean product regularly with a soft damp cloth.
Do not use abrasive or chemical cleaners as these will damage the product.
Product Location
Vanity units are only as strong as the wall to which they are xed and the xings that are used.
For different wall types you will need to ensure that you are using the correct type of xing for the material
of the wall.
The addition of backboards on the outside of the wall or appropriate strengthening of internal structures
may be required to provide adequate wall strength.
Maximum working load for vanity unit is 100kg when xed to a solid wall.
NOTE: If the wall is made of lightweight thermal blocks, aerated hollow brickwork or prefabricated
partitions even the most appropriate xings may not be able to withstand the loads which can be
suddenly applied to the vanity unit.
CAB 096 R01

2CAB 096 R01
Vanity Unit Components
Vanity Unit Fixing Components
A. Vanity Unit Base
(P001) x 1
E. Front Panel
(P005) x 1
B. Vanity Unit Side Panel
(P002) x 1
F. Rear Top Panel with
Hanging Baton
(P006) x 1
C. Vanity Unit Side Panel
(P003) x 1
G. Lower Draw Panel
(P007) x 1
D. Rear Panel
(P004) x 1
H. Lower Draw Base
(P008) x 1
I. Lower Draw Front
(P009) x 1
J. Top Drawer Panel
(P010) x 1
K. Draw Side Panel
(P011) x 2
L. Top Draw Base
(P012) x 1
M. Top Draw Front
(P013) x 1
N. Lower Draw
Side Panel
(P014) x 1
O. Lower Draw
Side Panel
(P015) x 1
R. Support Brace
(P018) x 2
A. Glue Pack
(H001) x 1
B. Cam Lock Pin
(H002) x 2
E. Countersink Screw
(H005) x 8
F. Runner screw
(H006) x 4
C. Cam Lock
(H003) x 2
D. Dowel
(H004) x 4
P. Concealed Runner
(P016) x 1
Q. Concealed Runner
(P017) x 1
H. Wall Plugs
(H007) x 2
G. Fixing Screws
(H006) x 2
I. Support Brace Screws
(H008) x 4

CAB 096 R01
3
Installation
Step 1
B. Vanity Unit Side Panel
(P002) x 1
C. Vanity Unit Side Panel
(P003) x 1
P. Concealed Runner
(P016) x 2
Q. Concealed Runner
(P017) x 2
E. Countersink Screw
(H004) x 4
E. Countersink Screw
(H004) x 4
Installation
Step 2
Click!
A. Vanity Unit Base
(P001) x 1
B. Vanity Unit Side Panel
(P002) x 1

CAB 096 R01
4
Installation
Step 3
Click!
C. Vanity Unit Side Panel
(P003) x 1

Installation
Step 4
Installation
Step 5
CAB 096 R01
5
E. Front Panel
(P005) x 1
F. Rear Top Panel with
Hanging Baton
(P006) x 1
D. Rear Panel
(P004) x 1
D. Rear Panel
(P004) x 1
E. Front Panel
(P005) x 1
F. Rear Top Panel with
Hanging Baton
(P006) x 1
D. Rear Panel
(P004) x 1
E. Front Panel (P005) x 1
F. Rear Top Panel with Hanging
Baton (P006) x 1
Click!
Click!
AB

Installation
Step 6
Installation
Step 7
Installation
Step 8
CAB 096 R01
6
Click!
N. Lower Draw
Side Panel
(P015) x 1
G. Lower Draw Panel
(P007) x 1
D. Dowel
(H004) x 4
H. Lower Draw Base
(P008) x 1
A. Glue Pack
(H001) x 1
B. Cam Lock Pin
(H002) x 2
I. Lower Draw Front
(P009) x 1
A. Glue Pack
(H001) x 1
O. Lower Draw
Side Panel
(P014) x 1

Installation
Step 9
Installation
Step 10A
CAB 096 R01
7
I. Lower Draw Front
(P009) x 1 C. Cam Lock
(H003) x 2
J. Top Drawer Panel
(P010) x 1
K. Draw Side Panel
(P011) x 2

Installation
Step 10B
Installation
Step 11
Installation
Step 12
CAB 096 R01
8
A B
Click!
J. Top Drawer Panel
(P010) x 1
K. Draw Side Panel
(P011) x 2
A. Glue Pack
(H001) x 1
L. Top Draw Base
(P012) x 1

Installation
Step 13
Installation
Step 14
Installation
Step 15
CAB 096 R01
9
Click!
A
B
M. Top Draw Front
(P013) x 1
Q. Support Brace
(P018) x 2
I. Support Brace Screws
(H008) x 4
E. Countersink Screw
(H005) x 4

e
Installation
Step 16
CAB 096 R01
10
Installation
Step 18
Stand Vanity Unit Upright!
Installation
Step 17
A. Hang ‘N’ Lock Bracket x 1
E. Hang ‘N’ Lock Cam x 2
H. Wall Plugs x 2
B. Hang ‘N’ Lock Bracket x 1 C. Hang ‘N’ Lock Spacer x 1
D. Hang ‘N’ Lock
Spacer (Small) x 1
F. Countersink Fixing Screws
x 2 (Optional)
G. Fixing Screws x 2 (Optional)
pack.
Only 2 x screws are required to install the
Hang ‘N’ Lock bracket. Please use either
supplied.
Assemble the Hang ‘N’ Lock bracket
sections making sure all parts are slotted
tightly together.
Image for reference only.
Determine the desired location for the vanity unit.
Place the Hang ‘N’ Lock bracket underneath the panel at the
rear of the vanity unit.
With a pencil mark through the screw hole positions in each
cam recess and draw a reference line under the Hang ‘N’ Lock
bracket.
Remove the vanity unit and the Hang ‘N’ Lock bracket from the
wall surface prior to drilling.

CAB 096 R01
11
Installation
Step 19
Installation
Step 20
Installation
Step 21
Installation
Step 22
Ø8
Drill the marked holes to a depth of 45mm.
Insert the wall plugs and loosely screw the
Hang ‘N’ Lock into position through the
Hang ‘N’ Lock cams.
With the Hang ‘N’ Lock bracket loosely
attached to the wall, adjust for height and
screwdriver and align the bottom of the
Hang ‘N’ Lock bracket with the reference
line. Once level fully tighten using a philips
screwdriver.
Using an 8mm drill, drill the marked holes through the
support braces.
Insert wall plugs and re-hang the vanity unit in
position aligning the holes in the support braces.
Using a philips screwdriver screw through the
braces to reinforce the vanity unit on the wall surface.
Hang the vanity unit onto the Hang ‘N’ Lock bracket, checking
the unit is level.
Using a pencil mark through the support braces and remove the
vanity unit.
IMPORTANT!
The support braces provide additional reinforcement to support
the weight of the vanity unit and basin. Reinforcement screws
must be secured through the support braces to provide
additional strength.
Support Brace
Ø8
G. Wall Plugs
(H007) x 2
F. Fixing Screws
(H006) x 2

CAB 096 R01
12
Installation
Step 26
For details of the other items in the Croydex range please visit our website: www.croydex.com
Croydex Ltd, Central Way, Andover, Hants, SP10 5AW, UK
Tel: [phone]
Fax: [phone]
Email: [email protected]
+
_3
A
B
CD
H. Runner Screws
(H008) x 4