Crua Outdoors MODUS User manual

MODUS
Instruction Manual
IN THE BOX:
Simply search “Crua
Modus Setup Video” on
YouTube
VIDEO
DEMONSTRATION:
Scan the QR code
or..
1. Take out and organize all the contents from
the carry bag.
2. Lay down the tent footprint and unroll the
mattress. Open the valve at the bottom
corner of the mattress to allow air to inate
the mattress. If the mattress does not feel
rm enough for you, you can add more air by
blowing or with the included pump.
1. Your Modus will come with a bug mesh and air-
poles. Attach the bug mesh by zipping it to the
base.
2. Un-roll the two air-poles and open the valve for
ination. The air-poles can be inated by mouth,
however, to achieve the correct PSI for the most
stability, use the included pump to ll the air-poles.
3. Once inated, place the air-poles on the Velcro
patches on either side of the mattress. The larger
air-poles goes on the head end and the smaller on
the foot end.
4. Locate the toggles on the bug mesh and place the
toggles through the loops on the air-poles.
B.) Erecting the Tent
A.) Set up
Base
Mattress/Quilt
Air-poles/Mesh/Footprint/Stakes
Flysheet
Flysheet/Poles/Tree Straps/Carabiners/Stakes
Base Deluxe
Deluxe Mattress/Quilt
Air-poles/Mesh/Footprint/Stakes
Extras
Connecting Flysheet
Cocoon

1. On the side you will be using as a porch, locate the
two circular eyelets and place the included porch
poles into the eyelet.
2. Tie a knot at the end of the two extra guy lines
provided. Slip the knot over the porch pole and guy
down each pole.
C.) The Flysheet (ii) Using the porch:
1. Simply place a set of poles from one Modus into the
eyelets of both.
2. Guy down each pole.
D. ) Connecting to Another Modus (i) Porch:
1. Place on the extra, connector yseet.
2. Guy it down securely for protection from the
elements or extra privacy.
D. ) Connecting to Another Modus (ii) Sleeping:
You loop it.. Swoop it.. and pull!
clip
clip
1. Find suitably spaced trees. You should look for
trees that are roughly 15 ft (4.5 meters) apart. Your
Modus comes with adjustable straps, so there is
exibility on distance.
2. Wrap tree straps around the tree a minimum of 4.5
ft (1.3 meters) o the ground.
3. Pull the end with multiple attach points, through the
single loop end. NOTE: based on the size of the tree
or distance between trees, you may need to wrap
the strap around the tree more than once.
4. Use the included carabiner to attach the tree strap
to the webbing at either end of the ysheet.
5. If the hammock feels too saggy, try to move
the carabiner up to the next adjustment point.
Continue until you nd the t comfort level for you.
D.) The Hammock
1. Place the ysheet over the base tent lining up the
air-poles with the center seams of the ysheet.
2. Stake down the head and foot rst ensuring that the
ysheet is centered appropriately.
3. Stake down the rest of the guy points. Note: the
guy points on the left and right side of the ysheet
have an elastic rope on them. This is to make it
easier for you to get in and out of the tent when
using the ysheet.
C.) The Flysheet (i) Covering the Base
NOTE: Your Modus ysheet is reversible. Place the
reective side in if you want to direct heat into your
tent. Place the reective side out if you want to
reect the heat away from your tent.