Crystal Mountain SmartFlo Use and care manual

TM
SmartFlo Water Cartridge
Replacement

TM
4. Open the replacement SmartFlo Water Cartridge kit, and remove the access key provided
TM
Replacement of SmartFlo Water Cartridge
5. Insert the access key into the 2 holes located at the underside of the top edge of the cooler (above water
levers) and push inwards (Figure 5 and Figure 6)(once unlocked, the front of the top cover opens
upwards)
TM
7. Unlock the turn knobs which hold down the SmartFlo Water Cartridge (Figure 8)
TM
Note: To reset the life timer system, the SmartFlo is required to be removed from the dispenser for a
minimum of 15 seconds while the unit is connected to the mains power supply.
2. Slide empty bottle out of cabinet (Figure 2)
TM
3. Open the replacement SmartFlo Water Cartridge kit and take red plug from kit. Disconnect the water
line from the bottle adaptor (Figure 3) and add red plug to waterline (Figure 4)
1. Open Dispenser Door (Figure 1). (Slide door upwards to allow access to bottle area)
TM
For the best quality and tasting water, it is recommended to change the SmartFlo Water Cartridge every
TM
12 months. Follow the steps below to replace the SmartFlo Water Cartridge. Recommend to empty the
TM
bottle installed in the cooler prior to replacement of the SmartFlo Water Cartridge and Bottle Adaptor.
6. Place a glass or other container below the water outlets (to catch drips), and unlatch the locking clip
located near the front of the cooler to release the water tubing (Figure 7)
TM
9. Discard used SmartFlo Water Cartridge according to local regulations. (Please recycle)
To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle
it responsibly to promote the reuse of sustainable resources.
TM
10. Insert water line of replacement SmartFlo Water Cartridge through the guide tube, and push through
to bottle installation area (Figure 10).
TM
8. Pull SmartFlo Water Cartridge upwards to remove (Figure 9)
Figure 9 Figure 10
Figure 1 Figure 2 Figure 3 Figure 4
Figure 5 Figure 6 Figure 7 Figure 8

Note: to maintain sanitization of the system, refrain from touching the section of the bottle adaptor tube
that is inserted into the bottle
22. Slide bottle into cabinet and close the door (Figure 18 to Figure 20) (slide door downwards to close)
23. Depress the and water levers to fill their respective tanks.Cold Hot
21. Remove red protective cap from the blue tube of the Smartflo™ Water Cartridge and install onto the
bottle adaptor assembly (Figure 17)
TM
11. Ensure seal is properly installed on the outlet tube of the SmartFlo Water Cartridge assembly (may
have shifted during shipment or un-packaging)
20. Push the tube to go through the Spike Cap, until it is close/hits bottom of the bottle (Figure 16)
16. Place fresh bottle outside of the cabinet
14. Close the locking clip to secure water outlet tubing in place (Figure 12)
TM
12. Align SmartFlo Water Cartridge with openings in cooler, and push into place
TM
13. Rotate turn knobs to lock SmartFlo Water Cartridge in place (Figure 11)
15. Close the top cover of the cooler (Figure 13) (push downwards to lock into place)
17. Clean the outside of the new bottle with a cloth. Remove security label/seal from the bottle cap (if applicable)
18. Remove bottle adaptor assembly from the empty bottle (Figure 14), and set aside. Carefully un-package
the Bottle Adaptor assembly, avoiding touching the tube.
19. Without touching the tube, install the Spike Cap (with the end of the tube in the Spike Cap) (Figure 15)
24. When water begins to flow from both faucets, the tanks have been filled (approximately 1 minute per
tank)
CAUTION! ALWAYS DRAIN WATER COMPLETELY BEFORE SHIPPING OR STORING THE COOLER!
Figure 11 Figure 12 Figure 13
Figure 14 Figure 15 Figure 16 Figure 17
Figure 18 Figure 19 Figure 20

Warning
This product dispenses water at very high temperatures. Failure to use properly can cause
ž
personal injury.
This dispenser is intended for dispensing water only. Do NOT use other liquids. Never use any
ž
other liquid in the dispenser other than known and microbiologically safe bottle water.
This appliance is not intended for use by persons (including children) with reduced physical,
ž
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
ž
Use with caution only
ž
The customer acknowledges that water, like other liquids, can cause damage to surfaces. The customer takes
full responsibility for placing the cooler within a residence or business, and acknowledges that failure to
address drips, leaks or spillages is at the customer’s risk.
The Warranty and Underwriters’ Laboratory for the coolers are invalidated if any alteration, modification, or
use or misuse in combination with any other machine or devices is deemed to be the source of any claim.
The manufacturer accepts no liability (including for bodily injury) resulting from any alteration, misuse,
neglect, accidents, improper installations or repairs.
DOC-C100109 Rev0520