CTC Union SHDTU03 User manual

USER MANUAL
SHDTU03
NTU/E1

SHDTU03-NTU/E1 SHDSL Modem
Installation and Operation Manual
Version 1.1
R
Re ev vi is si io on n M Ma ar rk ks s
Revision Date Notes
V 1.0
V 1.1
N/A
2003.10
Software: Version: 1.5X7001r-XAT0
Auto-configuration added
Software: Version 1.19 FW: 2.2

Table of Contents
i
Chapter 1. Introduction ……………..……....................
I. Features …………...…..…...……………………………… 1-1
II. Specification……………………………………………… 1-2
III. Application. ………….………………………………….. 1-3
Chapter 2. Hardware Installation ………....................
I. Front Panel ..……...…..…...……………………………… 2-1
II. Rear Panel……...………………………………………… 2-3
III. Hardware Installation .………………………………….. 2-4
Chapter 3. What's Auto Configuration …....................
I. Wet Current ..……...…..…...……………………………… 3-1
II. AIS (Alarm Indication Signal)……...………..…………… 3-1
Chapter 4. Configuration with Keypad and LCD .….
I. Purpose …....……...…..…...……………………………… 4-1
II. How to use key pads ?……..…...………………………… 4-1
III. Menu Tree …………...………………………………….. 4-2
1. Menu tree for SHOW STATUS………..……..
2. Menu tree for SHOW STATISTIC.....………..
3. Menu tree for SETUP TYPE………..………..
4. Menu tree for SAVE CONFIGURATION…....
5. Menu tree for DISGNOSTIC..…..……..……..

Table of Contents
ii
Chapter 5. Configuration with Console Port .…..….
I. Login Procedure …..…..…...……………………………… 5-1
II. Window structure………….…...………………………… 5-2
III. System Management Terminal(SMT) …….…………….. 5-3
1. Menu Command ...…………... ………..……..
2. Navigating the SMT interface…….....………..
IV. Main Menu Summary …..……………………………… 5-5
V. Changing the password and user profile………………… 5-6
VI. Configuration the SHDSL NTU ……………………….. 5-9
1. Configure SHDSL type………………..……..
2. Configure SHDSL parameters….......………..
3. Configure E1 parameters…….……..………..
4. Restore factory default …………………..…..
VII. Write the setup parameters.……….……………………5-22
VIII. Reboot the SHDSL NTU.………..……………………5-23
IX. View the system status ….……………………………..5-24
X. View the system configuration .…………………….…..5-26
XI. Upgrade the SHDSL NTU.………..…………………….5-27
XII. Diagnostic ….…………………………………………5-30
XIII. EXIT SMT .………………………………………….. 5-33
Appendix A …………………..…….................... A-1
Appendix B ……………………………….…….
I. Connector Architecture ….….…………………………… A-2
Appendix C ……………………. .…………..….
I. Cable Connection ………..….…………………………… A-4

Chapter 1. Introduction
1-1
I
I. . F Fe ea at tu ur re es s
The SHDSL NTU offers two different ways to connect customers to high-
speed TDM services with two G.703 E1 interfaces (balance 120 Ohm RJ45
jack or unbalance 75 Ohm dual BNCs). The G.703 interface will carry data
at N*64kbps rates (where n=1~32).
The SHDSL NTU can be configured and managed via EOC, or menu-driven
VT100 compatible Asynchronous Terminal Interface, either locally or
remotely.
The SHDSL NTU is equipped with an auto rate capability that identifies the
maximum line rate supported by the copper loop. This powerful automatic
configuration capability makes installation and service provisioning simple
and painless. Further flexibility is provided in the ability to manually set the
maximum NTU speed at different levels for different customer-tailored
service offerings.
?Standard G.shdsl (ITU G.991.2) supports improved reach/speed and
greater interoperability
?Fast and cost-effective provisioning of traditional frame relay (FR or T-
HDLC) or TDM leased line services
?Uses existing copper loop infrastructures
?Can operate in back to back connection
?Efficient single wire pair usage
?Up to 2.312Mbps symmetric service bit rate
?Auto rate installation maximizes data rate based on loop conditions
?Local management interface with LCD display
?Remote line loopback
?SHDSL Line performance monitoring
?Raw and per time interval statistics
?Bandwidth guaranteed transmission equipment

Chapter 1. Introduction
1-2
I
II I. . S Sp pe ec ci if fi ic ca at ti io on n
Network Interface
• Line Rate: SHDSL per ITU G.991.2
• Coding: trellis coded pulse amplitude modulation
• Support: ANSI (Annex A) and ETSI (Annex B)
• Payload rates: 64kbps to 2.304Mbps (N x 64kbps N=1 to 36)
• Connection: RJ-45 jack (2-wire)
G.703 Interface
• Connection: RJ-45 for balanced 120 Ohm E1 cable
• Connection: BNC for unbalanced 75 Ohm E1 cable
Framing
• G.703/G.704
• CRC 4 enable/disable
• CCS/CAS
• Framed / Unframed
DSL Timing
• Network / Internal / DTE
Performance Monitoring
• ES, SES, UAS, Alarms, Errors for E1, SHDSL
Loopback Tests
• Local / Digital / Remote Loopback
Management
• Configuration with keypad and LCD display
• Console port
• Supportsfirmware upgrade
Physical/Electrical
• Dimensions: 19.5 x 4.8 x 16.8 cm
• Input: 90~240VAC with 50~60Hz
• Power Consumption: 10W Max
• Operation: 0 to 50°C ; Humidity: Up to 95% (non-condensing)
!Warning! High voltage. Do not open

Chapter 1. Introduction
1-3
I
II II I. . A Ap pp pl li ic ca at ti io on n

Chapter 1. Introduction
1-4
This page is left in blank intentionally

Chapter 2. Hardware Installation
2-1
This chapter shows the front panel and how to install the hardware.
I. Front Panel
The front panel contains LED status
The LCD can show the status and configuration of the product. The
local management interface will be done by push button keys and LCD
display. For more detail, refer to Chapter 4: Configuration.
The purpose of key pad is to configure the SHDSL NTU. Review
Chapeter 4 for detail configuration.
Key Pad Description
Exit/-Return to previous configuration menu.
Enter/+ Skip to next configuration menu or configure the items.
LSelect other parameter in the same level menu.
RSelect other parameter in the same level menu.

Chapter 2. Hardware Installation
2-2
The following table describes the LEDs’ function of the SHDTU03.
LED Color
Action Description
On Power is on.
PWR Green
Off Power is off.
On Major alarm occurs.
ALM Red Off System is working normally.
On System is testing for connection.
System
TST Yellow
Off System is working normally.
On SHDSL line is connected.
Blink Data transmit in SHDSL line.
SYN Green
Off SHDSL line has dropped.
Blink There are error seconds.
ERR Red Off There are not any error seconds.
On Loopback is on.
SHDSL
LBKYellow
Off Loopback is off.
On E1 line is connected.
SYN Green
Off E1 line has dropped sync.
Blink There are error seconds.
ERR Red Off There are not any error seconds.
On Loopback is on.
G.703
LBKYellow
Off Loopback is off.

Chapter 2. Hardware Installation
2-3
I
II I. . R Re ea ar r P Pa an ne el l
From left to right, the rear panel of SHDSL NTU includes the power
switch, power socket, RJ-45 console, RJ-45 G.703, BNC jacksfor
transmitting and receiving and the RJ-45 for SHDSL.
Rear Panel with the AC Type
Rear Panel with the DC Type
Connector Description
Power Power switch. Press 1 to turn on and press 0 for off.
100~240V AC Power socket. It has power adapting function from 90~240VAC.
36~72VDC Power socket . It has power adapting function from 36~
72VDC.
Console RJ-45 for system configuration and maintenance.
E1/120ORJ-45 for 120 Ohm E1 connection with PABX (Private
Automatic Branch Exchange) or Router
TX BNC for 75 Ohm E1 transmitting
RX BNC for 75 Ohm E1 receiving
G.SHDSL RJ-45 for G.SHDSL connection

Chapter 2. Hardware Installation
2-4
I
II II I. . H Ha ar rd dw wa ar re e I In ns st ta al ll la at ti io on n
Note: To avoid possible damage to the SHDTU03, do not turn on the product before
hardware installation.
1. Plug the power cord in the power socket.
2. Plug the console port in console if you want to configure the NTU with VT100
program of NB or PC.
3. Plug in the E1 cable (Either 75 Ohm BNC cables or 120 Ohm twisted pair cable)
4. Plug in the SHDSL cable
5. Power on
Power
Source
90~240V AC
CONSOLE
Power E1 TX RX G.SHDSL
PC
or
NB
PABX
or
Router
Console
Cable
BNC
Cables Twisted
Pair
Power
Cord
RJ-45
Cable
PABX
or
Router DSL
!Warning! High voltage. Do not open

Chapter 3. What is Auto Configuration
3-1
Some of the embedded functions do not have a separate command to setup
but some of them are auto sense with some configurations and change itself
configuration. Some of them are always enable function.
I. Wetting Current
Wetting current, also known as loop sealing current, is a low-level DC current
applied to a loop for the specific purpose of maintaining cable splice integrity by
preventing the build-up of oxidation. The “enable”applies a relative –42 ±2 V DC
voltage to the cables and allows 2~3 mA of current to flow at all times.As with all
STU-C type devices, they have the ability to source wetting current. The SHDTU03
will automatically enable wetting current as STU-C type. As STU-R type, it always
terminates the wetting current.
II. AIS (Alarm Indication Signal)
Alarm Indication Signal (RAI) is an always enabledsignal transmitted
automatically to the connected device when the remote E1 line dropsor the SHDSL
line drops. For example: When STU-R E1 RX line is dropped, STU-R will send the
status to STU-C via EOC or command. STU-C will send AIS (Alarm Indication
Signal) to DTE.
DTEDTE STU-C STU-R
E1 SHDSL E1
E1 Line Drop
RAI
EOC or CommandAIS

Chapter 3. What is Auto Configuration
3-2
This page is left in blank intentionally
.

Chapter 4. Configure via Keypad and LCD
4-1
I. Purpose
This chapter provides information about configuration your SHDSL
NTU via the front panel LCD display and keypads.
Note: After you have completed all necessary settings for your SHDSL
NTU, make sure to write the new configuration to NVRAM by “write”
command and reboot the system for the of new configuration to take effect.
II. How to use key pads
The SHDTU03 is designed for user-friendly configuration with keypads
and LCD display without using PC or NB with VT100 terminal.
Key Pad Description
Exit/-Return to previous configuration menu.
Enter/+ Skip to next configuration menu or configure the item.
LSelect other parameter in the same level menu.
RSelect other parameter in the same level menu.

Chapter 4. Configure via Keypad and LCD
4-2
III. Menu Tree
After turning on the SHDTU03, the LCD will prompt SHDSL NTU (E1).
Press Enter to enter. There are five main commands, show status, show
statistics, system setup, write configuration and system diagnostic. For
more detail, refer to each title.
SHDSL NTU
====(E1)==== SHOW STATUS
SHOW
STATISTIC
SYSTEM
SETUP
WRITE
CONFIGURATION
SYSTEM
DIAGNOSTIC
STATUS
TYPE
STATUS
SHDSL
STATUS
E1
STATISTICS
CURRENT 15MIN
STATISTICS
CURRENT 24HR
STATISTICS
PREVIOUS 15MIN
STATISTICS
PREVIOUS 24HR
STATISTICS
CLEAR ALL
SETUP
TYPE
SETUP
SHDSL
SETUP
E1
*SAVE & REBOOT*
YES
DIAG
LOOPBACK
*SAVE & REBOOT*
NO
Refer to next picture
Refer to next picture
Refer to next picture
Refer to next picture
Refer to next picture
Refer to next picture
Refer to next picture
Refer to next picture
Refer to next picture
Refer to next picture
Refer to next picture
Refer to next picture

Chapter 4. Configure via Keypad and LCD
4-3
Menu tree for SHOW STATUS
You can check three kinds of status via LCD display: Type, SHDSL status
and E1 status. The SHOW STATUS menu tree is as follows.
SHOW
STATUS STATUS TYPE
STATUS
SHDSL
STATUS
E1
* TYPE *
**********
* DATA RATE *
*** Kbps
* TX POWER *
*** dBm
* ATTENUATION *
*** dB
* SNR MARGIN *
*** dB
* SYNC *
***********
* LINE CODE *
**********
*FRAME FORMAT*
*********
*RAI GENERATION*
**********
* BUILD OUTS *
*** Ohm
* E BIT GEN *
**********
SHDSL NTU
====(E1)====

Chapter 4. Configure via Keypad and LCD
4-4
Menu tree for SHOW STATISTIC
The SHDTU03 can display for current 15 minutes and current 24 hours.
The menu tree is as follows.
SHOW
STATISTIC
STATISTICS
CURRENT 24HR
STATISTICS
PREVIOUS 15MIN
STATISTICS
PREVIOUS 24HR
STATISTICS
CLEAR ALL
CURRENT 24HR
SHDSL
CURRENT 24HR
E1
* SHDSL ES *
*********
* SHDSL SES *
*********
* SHDSL UAS *
********
* SHDSL LOSW *
********
* E1 ES *
*********
* E1 SES *
*********
* E1 UAS *
********
QUARTER
1* SHDSL ES * *********
* SHDSL SES *
*********
* SHDSL UAS *
********
* SHDSL LOSW *
********
* E1 ES *
*********
* E1 SES *
*********
* E1 UAS *
********
DAY
1
DAY
7
* SHDSL ES *
*********
* SHDSL SES *
*********
* SHDSL UAS *
********
* SHDSL LOSW *
********
* E1 ES *
*********
* E1 SES *
*********
* E1 UAS *
********
* CLEAR *
YES
CURRENT 15MIN
SHDSL
CURRENT 15MIN
E1
* SHDSL ES *
*********
* SHDSL SES *
*********
* SHDSL UAS *
********
* SHDSL LOSW *
********
* E1 ES *
*********
* E1 SES *
*********
* E1 UAS *
********
STATISTICS
CURRENT 15MIN
SHDSL NTU
====(E1)====
QUARTER
96