CTX EX-710F User manual

Ex710F User’s Manual
1
User’s Manual
EX710F

Ex710F User’s Manual
2
Table of Contents
1. Safety Instructions 3
2. Recommendation for Optimum Performance 7
3. Introduction 8
4. Installation 9
5. Controls and Adjustments 11
6. Trouble Shooting 18
7. Energy Declaration 20
8. Specification 21
9. Reference Information 22

Ex710F User’s Manual
3
Safety Instructions
FCC Statement
This equipment has been tested to comply with the limits for a class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning:
If a shielded-type power cord is supplied with this monitor, it is required in
order to meet FCC emission limits and to prevent interference with nearby
radio and television reception. Only shielded cables should be used to
connect I/O devices to this equipment. You are cautioned that changes or
modifications not expressly approved by the party responsible for compliance
could void your authority to operate the equipment.
CE Statement
This device complies with the requirements of EMC (Electromagnetic
Compatibility), and with Low Voltage directive.

Ex710F User’s Manual
4
Safety Precautions
1. Please read carefully all of these instructions below and keep the manual
for later use.
2. Please install the swivel base below this product before using it.
3. The voltage ratings and the rated frequency are on the overlay centered at
rear side of this product. Do not connect with any other sources of voltage or
frequency, and please follow all warnings and instructions marked on the
product.
4. Unplug this product from the wall outlet before cleaning and use a damp
cloth to clean it. Do not use liquid cleaners or aerosol cleaners.
5. Do not expose this product to rain or moisture.
6. Do not place this product on an unstable cart, stand, or table. The product
may fall, causing serious damage to the product.
7. Do not block or cover ventilating openings with cloth or other material.
Neither should this product be placed near or over a radiator or a heat register,
nor should the product be placed in a built-in installation unless proper
ventilation is provided.
8. This product is equipped with a 3-wire grounding model plug. This plug will
only fit into a grounding-model power outlet. This is a safety feature. If you are
unable to insert the plug into the outlet, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of the grounding-model plug.
Choose a Tandem Blade attachment plug configuration power cord for 230V
AC input.
Due to the safety requirements of different areas, please
select a suitable power cord according to the following rules,
in addition to the electric rating:
A. Northern America area: Please select a UL listed and CSA
certified power cord.

Ex710F User’s Manual
5
B. Germany: Please select a VDE certified power cord.
C. Nordic countries: Please select a power cord certified by
SEMKO, NEMKO, DEMKO or FIMKO.
D. The other areas: Please select a power cord suitable to the
local power system and power outlet.
Usually, when this product is sold, the manufacturer provides
a suitable power cord. However, this product is sometimes
resold or transported to another area, with different power
system and safety requirements. Please pay attention to the
selection of a suitable power cord. The plug on the power
cord is intended to serve as the disconnect device, the
socket-outlet shall be installed near the equipment and shall
be easily accessible.
9. Do not allow anything to rest on the power cord. Do not locate this product
where persons can walk on the cord.
10. Never push objects of any kind into this product through cabinet slots as
they may touch dangerous voltage points or short out parts that could result in
the risk of fire or electric shock. Never spill liquid of any kind on the product.
11. Do not attempt to service this product yourself, as opening or removing
covers may expose you to dangerous voltage points or other risks. Refer all
servicing to service personnel.
12. Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions.
A. When the power cord or plug is damaged or frayed.
B. If liquid has been spilled into the product.
C. If when the operating instructions are followed, the product
has been exposed to rain or water.

Ex710F User’s Manual
6
D. If the product does not operate normally, adjust only those
controls that are covered by the operating instructions since
improper adjustment of other controls may result in damage
and will often require extensive work by a qualified technician
to restore the product to normal operation.
E. If the product has been dropped or the cabinet has been
damaged.
F. If the product exhibits a distinct change in performance,
indicating a need for service.
Notice : Actual safety specifications please refer to the label on the back
of monitor.

Ex710F User’s Manual
7
Recommendation for Optimum Performance
When setting up and using the monitor, pay special attention to the following
for optimum performance:
• Do not use your monitor against a bright background or where
sunlight or other light sources will shine directly on the screen.
• The monitor should be placed just below eye level (10°~15° ) for
optimum viewing.
• Set the monitor's brightness to match the ambient room light.
• For optimum focus, the contrast control should not be set to the
maximum level unless the input signal level is extremely low. Also, the
brightness control should be set to a point where the overall
background area just begins to disappear.
• Allow adequate ventilation around the monitor so that the heat from
the monitor can properly dissipate.
• Neither the monitor itself, nor any other heavy objects, should rest on
the power cord. Damage to the power cord can cause fire or electrical
shock.
• Keep the monitor away from high-capacity transformers, electrical
motors, or other strong magnetic fields.
• Your monitor should not be used in damp, dusty, or dirty areas.
• Handle your monitor with care when transporting it.
CAUTION
• Do not scrap or knock the surface of CRT with a pen, a screwdriver
and so on.
• Clean the CRT surface with a lint-free, nonabrasive, soft cloth, and
should not use the solution or glass cleaner containing corpuscles like
an abrasive, alcohol and an alkaline solution.

Ex710F User’s Manual
8
Introduction
The monitor is a multiple frequency high-resolution color monitor for IBM
compatible PC's or Macintosh and workstation systems. The monitor is
equipped with microprocessor based intelligence and multiple frequency
scanning capability, allowing it to provide maximum compatibility for various
system platforms.
The monitor uses the latest screen technology including a Flat CRT to display
crisp text and vivid color graphics. The full-function digital control and
On-Screen Display (OSD) system provides easy adjustment of image
geometry and color settings for different display modes with the precision of a
fixed frequency monitor.
The monitor also has full ergonomic features. In addition to the friendly
controls and user comfort features, the emission level of the electric and
magnetic field is kept low to meet the Swedish MPR II or TCO standards.
The monitor is also equipped with energy saving functions; it is compatible
with the VESA power saving standards.

Ex710F User’s Manual
9
Installation
Unpacking
The following lists all of the items included in the monitor package box.
Please save the original box and packing materials for future transportation or
shipment of the monitor.color monitor package should contain the following
items:
Color monitor with tilt/swivel base
(with Signal cable)
Power cord
User's Guide / Driver CD
System Setup
1. Turn off the system and all attached peripherals.
2. Carefully turn the monitor upside down.
Remove the Tilt/Swivel Base

Ex710F User’s Manual
10
1. Squeeze and hold the latches.
2. Pull the tilt/swivel base to the rear of the monitor and lift to remove the base.
Installing the Tilt/Swivel Base
1. Align the base with the slots on the bottom of the monitor and insert the
tilt/swivel base into the slots.
2. Push the tilt/swivel base firmly toward the front of the monitor until the
latches click into the locked position.
Please save the original box and its packing materials for future transportation
or shipment of the monitor.

Ex710F User’s Manual
11
Control and Adjustments
Once you have installed the monitor for your system, please read the
instructions of this section which give you some guidelines on how to use the
monitor more efficiently. It leads you through the various function of the user
controls and explains how to adjust the monitor to your personal preference.
Front Panel Controls
1. POWER BUTTON
2. POWER INDICATOR
As long as the monitor is powered this indicator is lit. In
normal operation it lights green, while in power saving mode
the indicator will turn to amber.
3. ENTER BUTTON( )
To open On Screen Display (OSD) Menu or Enter
Subdirectory and execute it.

Ex710F User’s Manual
12
4. CONTROL BUTTON
To scroll select the OSD Menu or to adjust the parameter of a
selected function.
5. EXIT BUTTON (ESC)
To exit OSD window.
Power Saving Note:
This monitor is equipped with automatic power-saving
circuitry design which will work with any computer unit
following the VESA DPMS detection format, and the
ENERGY STAR low power state definition. Every time when
you first turn on your PC and monitor ,the power save
function remains inactive, the function will then be triggered
when the input signal from the PC is cut off by the computer
itself, or through some other loss of signal input afterwards.
OSD (On-Screen Display) Controls
(1) Press " " to open the On-Screen menu function. Seven adjustment
functions will appear on the On-Screen menu.
Press " " or " " button to scroll selections from top-down sequence.
Press " " to enter the item which is selected or to activate the preferred
adjustments.
Press "ESC" to exit the On-Screen Menu or up level.

Ex710F User’s Manual
13
A. Status
To display existing timing data of resolution and frequency.
B. Picture
1. Press " " or " " to select Vertical and
Horizontal position, Vertical and Horizontal size.
2. Press " " to process.
3. Press " " or " " to preferred picture.

Ex710F User’s Manual
14
C. Geometry
1. Press " " or " " to select Side-pin, Balance, Keystone,
Parallel, Rotate and Corner.
2. Press " " to process.
3. Press " " or " " to preferred picture.
D. Color
1. Press " " or " " to select 9300°K, 6500°K or
5000°K white color temperature standards.
2. In User item, presses " " to confirm action
color adjustment.
3. Press " " or " " to select Red, Green and Blue then
press "Enter" to process.
4. Press " " or " " increase or decrease density.

Ex710F User’s Manual
15
E. Advanced
1. Press " " or " " to select H.(Horizontal) and
V.(Vertical) moire or Degauss.
2. Press " " to process.
3. Press " " or " " to reduce H. Moire or V. Moire.
Caution:
1. If moire reduction is overdone, picture quality, i.e. focus
and vertical line stability will both be effected.
2. Proper adjustment is recommended for not effecting
picture performance.
F. Recall
Press the " " to confirm the Recall action.

Ex710F User’s Manual
16
Confirm the Recall action by pressing the " " or cancel the
action by pressing the "ESC".
If this window appears, that means it cannot be
preset.(factory mode only)
G. Language
Press " " or " " to select the Language for OSD only.

Ex710F User’s Manual
17
(2) Contrast/Brightness:
When OSD is off, " " or " " will be adjust contrast or brightness.
* All adjustments except color adjustment will be automatically saved.
* The menu block will disappear after 20 seconds without any data changing
or press "ESC" botton directly.

Ex710F User’s Manual
18
Trouble Shooting
Before calling an authorized service center, please check that the items below are
properly connected or set.
In case of using a non-standard signal, please check the pin assignments and the
signal timing of your adapter with the specifications outlined in sections "Pin
Assignment Table" and "Preset Timing Chart".
Problem Items to check
No picture Power Switch should be in the ON position, and the
power cord should be properly connected.
Check the color of the power LED indicator; if it is
orange, then the monitor is in a power saving mode.
Check if the horizontal/vertical frequency are out of
range.
Maximize the Brightness and Contrast controls.
"No Signal Input" is
displayed on the screen
The video card may not be seated properly. Make
sure it is fully seated in its slot.
Make sure the signal cable is connected securely to
the video card or computer.
Enable "Power Save" function.
Display image is not
centered, too small, or
too large
Refer to "Controls & Adjustments." You need to
adjust "Size" and "Position" of the image.
Image is scrolling or
unstable
Make sure the signal cable is connected securely to
the video card or computer.

Ex710F User’s Manual
19
Picture is fuzzy Adjust Contrast and Brightness controls.
On all Models select the Degauss function in the
OSD control menu.
CAUTION:
A minimum interval of 20 minutes should exist
before the degauss button is pressed a second time
when not switching between modes. Do not hold
the button down continuously.
Picture bounces or a
wave pattern is present in
the picture
Move devices that might be causing electrical
interference away from the monitor. (See "FCC
Information.")
Edges of the display
image are curved either
inward or outward
Refer to "Controls and Adjustments." You need to
adjust the "Side Pincushion."
No Plug & Play
functionality
Verify that the host system is Plug & Play
compatible.
Check to see if Windows 95 is installed, and the
software key for the Data Display Channel (DDC)
function is enabled.
Determine if original manufacturer's detachable
signal cable is being used (D-Sub-15 pin only).

Ex710F User’s Manual
20
Energy Declaration
This monitor is equipped with a function for saving energy which supports the
VESA Display Power Management Signaling (DPMS) standard. This means
that the monitor must be connected to a computer which also supports the
VESA DPMS standard to fulfill the requirements of the NUTEK specification
803299/94/96. The time settings for switching to a power saving mode are
adjusted from the system unit by software. From the first indication of inactivity
to power saving position A2 the total time must not be set to more than 70
minutes.
1. VESA Power-Management Proposal
H. sync V. sync Video State
Off On Blank Stand-by
On Off Blank Suspend
Off Off Blank Off
2. Power Consumption (120/230 Vac)
NUTEK VESA
state
LED
indicator
Power
Consumption
Normal operation On Green < 100W
Power Saving
Position A1 Suspend
Amber <15W
Power Saving
Position A2 Off Amber <5W