CTX S700A User manual

S700A
S700BA
S720A
SERVICE MANUAL
The Monitor S
p
ecialists EDITION 1
DEC. 2003

C
C
CT
T
TX
X
X Service Manual
S762A
2
TABLE OF CONTENTS
CONTENTS PAGE
Sections
1. Scope 4
2. Input requirements 5
3. Electrical Characteristics 6~10
4.Trouble Shooting 11~16
5. Parts List 16
Appendix
1. Main Board Circuit Diagram
2. Assembly Explosion Drawing

C
C
CT
T
TX
X
X Service Manual
S762A
3
Copyright © 2003 by Chuntex Electronic Co., Ltd.
The CTX SERVICE MANUAL is published by Chuntex Electronic Co., Ltd
All rights reserved. No part of this manual may be used, copied, reproduced, or transmitted in any form or by
any means for any purpose without the express written permission of the publisher.
The publisher has been trying its best to make this publication perfect, and in this manner takes no
responsibility for the use of any of the materials or methods described in this manual, or for the products
thereof. Neither will the publisher be responsible for any damages caused by misuse or misquotation.
Information in this manual is subject to change by the publisher without any notice in advance.
CTX is a registered trademark of Chuntex Electronic Co., Ltd.

C
C
CT
T
TX
X
X Service Manual
S762A
4
1. SCOPE
This specification defines the design and performance requirements for the 17” SXGA TFT
LCD display monitor “S762A “.
The features of “S762A” is listed in the following table :
Feature Description
1 Universal input AC/DC power supply inside the monitor
2 Analog RGB interface (VGA ) 30~80KHz, 59~75Hz, 135MHz
3 17” SXGA 1280*1024, TFT LCD panel
4 Function keys * 5 : Power On/Off, ESC,△ (up), ▽ (down), (enter)
5 Direct Acess function keys : △ for contrast function, ▽ for brightness function .
ESC for audio mute function.(S761A/S762A/S760A only)
6 Green/Amber LED indicator for power on/power saving
7 Plug & play support with DDC2B protocol installed.
8 Power saving mode compliant with Energy Star
9 OSD (on screen display) MENU operation
9.1 Brightness adjustment
9.2 Contrast adjustment
9.3 Auto tune function (VGA)
9.4 Color selection
9.5 Image adjustment
9.6 Language selection
9.7 OSD position adjustment
9.8 Reset function
9.9 1W * 2 Audio function inside the monitor (S762A/S761A /S760A Only)
9.10 Volume adjust by OSD (S762A/S761A/S760A Only)

C
C
CT
T
TX
X
X Service Manual
S762A
5
2. INPUT REQUIREMENTS
2.1 Input Power
2.1.1. Power Source 100 ~ 240 Vac, + -10%, 50/60 Hz
2.1.2. Power Consumption
2.1.3. AC Line Drop Out
2.1.4. AC Wave Distortion
2.1.5. In-rush Current
2.1.6. Power Cord
Normal operating mode
Audio function is operating at max output: ≦39W
w/o audio function: ≦36W
Power saving mode
Audio function is operating at max output: ≦7W
w/o audio function: ≦2W
Power switch off: ≦1W
Picture must not disappear while AC 100 V input drop out(10ms, 100%)
10% max. Permitted
50 A max at 240 Vac cold start
Detachable, 3P with ground type.
2.2 Display Input
2.2.1. Analog Input RGB Video
2.2.1.1 Sync Signal
Analogue, 0.0 to 0.7 V peak to peak
Separate RGB
Input impedance 75 Ohm
Positive polarity
Separate horizontal & vertical sync (3.3V & 5V)
Low level 0.8 V maximum
High level 2.0 V minimum
Positive or negative polarity
Analog Input Connection a. Captive cable length 1.5M in LCD Monitor end, D-sub
male connector in another end.
b.AfemaleMiniD-sub15pinbase.

C
C
CT
T
TX
X
X Service Manual
S762A
6
Pin 1 Red
Pin 2 Green
Pin 3 Blue
Pin 4 No Connection
Pin 5 Ground
Pin 6 R Return
Pin 7 G Return
Pin 8 B Return
Pin 9 DDC +5V
Pin 10 Ground
Pin 11 Ground
Pin 12 SDA
Pin 13 H. Sync
Pin 14 V. Sync
Pin 15 SCL
2.3 Audio Input (S760A/S761A/S762A only)
2.3.1 Audio Input Signal Right &Left channels.
Input level: 1Vrms(typ), 2Vrms(max)
Input Impedance: 15Kohm
2.3.2 Audio Input Connection a. Detachable stereo phone head in two ends signal cable.
b. A female stereo phone jack base.
3. ELECTRICAL CHARACTERISTICS
3.1 LCD Panel
3.1.1. Type 17” diagonal, SXGA resolution, color TFT-LCD
3.1.2. Pixel structure R/G/B sub-pixels in vertical stripes
1280 x 1024 array matrix
a-Si TFT active matrix
3.1.3. Gray scale 16 million colors.
3.1.4. Surface treatment 3H hard coating, anti-static, anti-glare
3.1.5. Backlight
Integral CCFL, type to support field replacement.
Life time 30000 hours @ 25C, 50% of initial value.
3.1.6 Pixel Faults
Model
Project
Pixel Faults type
S762A/S761A/S760A/S762/S761/S760
LBL17S24HA01/LBL17B24HA01/LBL17W24HA01
LBL17S24HA/LBL17B24HA/LBL17W24HA
Type Bright Pixels (Note 1) ≦5
Type Dark Pixels (Note 2) ≦5
Type Fault Pixels / Sub-Pixels(Note 3) ≦3
Type Cluster of type1 or type 2
f(
)
≦2
Type Cluster of type3 faults (Note4) ≦3
Type Total Pixel Faults ≦8
Note 1 : Bright pixels in full black pattern.
Note 2 : Dark pixels in full white pattern
Note 3 : fault Pixel / Sub-Pixel : The pixel or sub-pixel is abnormal but not bright/dark pixel.
Note 4 : Fault Cluster : Two or more Pixels/Sub-pixels with faults within 5 * 5 block of pixels.

C
C
CT
T
TX
X
X Service Manual
S762A
7
3.2 Modes and Timing Comparability
3.2.1Analog Input Supported Timing VESA Standard mode:
Display Format IBM VGA VESA VESA VESA VESA VESA
Horizontal Dots 720 640 640 640 800 800 800
Vertical lines 400 480 480 480 600 600 600
Horizontal Frequency 31.469 37.861 37.5 37.879 48.077 46.875
Vertical Frequency ( Hz ) 70 59.94 72.809 75 60.317 72.188 75.000
Pixel Rate ( MHz ) 28.322 25.175 31.5 31.5 40 50 49.5
H. Sync. Polarity - - - - + + +
A
μ
S
(Period)
31.778 26.413 26.667 26.4 20.8 21.333
B
μ
S
(PulseWidth)
3.813 1.270 2.032 3.2 2.4 1.616
C
μ
S
( Back Porch )
1.907 4.063 3.810 2.2 1.28 3.232
D
μ
S
(ActiveArea)
25.422 20.317 20.317 20.0 16.0 16.162
E
μ
S
(Front Porch )
0.636 0.763 0.508 1.00 1.12 0.323
V. Sync. Polarity + - - - + + +
O ms ( Period ) 16.683 13.735 13.333 16.579 13.853 13.333
P ms ( Pulse Width ) 0.064 0.079 0.080 0.106 0.125 0.064
Q ms ( Back Porch ) 1.048 0.739 0.427 0.607 0.478 0.448
R ms ( Active Area ) 12.711 15.253 12.678 12.800 15.840 12.480 12.8
S ms ( Front Porch ) 0.318 0.237 0.027 0.026 0.770 0.021
Display Format VESA VESA VESA VESA VESA VESA
Horizontal Dots 1024 1024 1024 1152 1280 1280
Vertical lines 768 768 768 864 1024 1024
Horizontal Frequency 48.363 56.746 60.023 67.5 63.981 79.976
Vertical Frequency ( Hz ) 60.004 70.069 75.029 75 60.013 75.025
Pixel Rate ( MHz ) 65.0 75 78.75 108 108 135
H. Sync. Polarity - - + + + +
A
μ
S
(Period)
20.667 17.707 16.660 14.815 15.631 12.504
B
μ
S
( Pulse Width )
2.092 1.813 1.219 1.185 1.180 1.067
C
μ
S
(BackPorch)
2.462 1.920 2.235 2.370 2.065 1.837
D
μ
S
(ActiveArea)
15.754 13.653 13.003 10.667 11.797 9.481
E
μ
S
(Front Porch )
0.369 0.321 0.203 0.593 0.590 0.119
V. Sync. Polarity - - + + + +
O ms ( Period ) 16.666 14.272 13.238 13.333 16.663 13.329
P ms ( Pulse Width ) 0.124 0.106 0.050 0.044 0.047 0.038
Q ms ( Back Porch ) 0.6 0.513 0.466 0.474 0.594 0.475
R ms ( Active Area ) 15.88 13.599 12.795 12.8 16.006 12.804
S ms ( Front Porch ) 0.062 0.054 0.017 0.015 0.016 0.012
VGA Support Mode
1280 * 1024 @70Hz,72Hz
1280 * 960 @ 60Hz,70H,72Hz,75Hz
1280 * 720 @ 60Hz
1152 * 864 @ 60Hz, 70Hz,72Hz
1024 * 768 @ 72Hz
800 * 600 @ 70Hz
640 * 480 @ 70Hz
640 * 350 @ 70Hz

C
C
CT
T
TX
X
X Service Manual
S762A
8
3.3 Plug & Play DDC 2B data transmission only for I2C BUS interface card.
3.4 Scanning characteristics VGA
Video
H Sync
B C D E
Video
V Sync
P Q R S

C
C
CT
T
TX
X
X Service Manual
S762A
9
Horizontalfrequency 30KHzto80KHz
Refreshrate 59Hzto75Hz
3.5 Audio Module (S762A/S761A/S760A)
3.5.1.Type: StereoBTLaudiooutputamplifierwithDCvolumecontrol
withtwo1Wspeakers.
3.5.2.InputLevel: 1Vrms
3.5.3.OutputPower: 1W*2(10%THD,1KHz)
3.5.4. Total Harmonic Distortion (THD): 0.3% (Typ.) (0.5W * 2, 1KHz)
3.5.5. Frequency Response ±3dB: 550Hz ~ 20KHz
3.5.6. Channel unbalance (output power): 1dB (max.)
3.6 User Controls and Indicator
3.6.1 Power ON/OFF Switch
3.6.2 LED Indicator
3.6.3 OSD
3.6.3.1 Buttons
3.6.3.2 OSD Menu Level
3.6.4 Hot Keys Function
3.6.4.1 Contrast ( )
3.6.4.2 Brightness ( )
The switch control scaler power down and turn off panel.
The LED color shall indicate power status as shown in
paragraph 3.7
ESC ,▽, △,
See Table 2. S762A/S761A/S760A/S762/S761/S760 OSD Control
Map
Press “△” to pop up ;then press “△” or “▽” to adjust Contrast
up or down.
Press “▽” to pop up ;then press “△” or “▽” to adjust
Brightness up or down.
*3.6.4.3 Mute On ( )
*3.6.4.4 Mute Off ( )
*3.6.4.5 In monitor power saving mode
Press “Esc” directly to disable speakers, while speakers in
normal state.
Press “Esc” directly to enable speakers, while speakers in
audio mute state.
“Esc” key is for Mute On and Off function
“△” key is for increasing volume function.
“▽” key is for decreasing volume function.
“ESC” key is enable or disable audio mute.
Note:*meansS762Aonly
Table 2 S762A OSD Control Map
1.VGA-D15 input:

C
C
CT
T
TX
X
X Service Manual
S762A
10
Level 1 Level 2 Level 3 Level 4
Direct Ad
j
Bri
g
htness
Direct Ad
j
Contrast
*Direct Ad
j
*Audio Mute
*Volume *Ad
j
ustment scale
Auto Tune
Auto Colo
r
9300° K
6500° K
Color
Use
r
R/G/B select Ad
j
ustment scale
Clock Ad
j
ustment scale
Phase Ad
j
ustment scale
H-Position Ad
j
ustment scale
V-Position Ad
j
ustment scale
Image
Smooth On/Off
En
g
lish
(
select
)
German
(
select
)
French
(
select
)
S
p
anish
(
select
)
Italian
(
select
)
Language
中文
(option)
H-Position Ad
j
ustment scale
V-Position Ad
j
ustment scale
OSD Position
Cente
r
Main Menu
Reset Yes/No
Note:* means S762A/S761A/S760A only
3.6.5 Accessory OSD Indications
Signal out of range An input signal which is outside the range defined in
Section 3.4 shall cause the monitor to display a message
Signal Out of Range.
No Signal Input and power down. When the signal cable is not plugged into PC or when the
horizontal or vertical sync are absent and when the
monitor is turned on. After 5 sec isn’t to detect H or V Sync
then show “No Signal Input” for 5 seconds and then show ”
Power down” message on screen 2 sec. And then the
monitor shall go to power saving status. If first turn on the
monitor, shows “No Signal Input” 30 sec.
3.7 Power Management

C
C
CT
T
TX
X
X Service Manual
S762A
11
This monitor will meet the low power specification, Including USA governmental requirements
For Energy Star, the NUTEK standard and the VESA DPMS standard which detected the Hori. /Vert.
Sync signal from host CPU.
A dual color (green/amber) LED is located on the front bezel to indicate the power management
states.
Status
Sync. Video
Power
consumption
Power
management Picture Recovery time LED Color
Active Active
With Audio: 39W
Without Audio:36W On - Green
No Sync. Blanked ≦2W
(Note.1) Power saving ≦3 sec Amber
Note. 1: Audio function is operating at no signal input.
Once “Esc” or “△” or “▽” key initiates under power saving condition, the audio function
can be waked up and the power consumption can not be the above definition.
S762Aonly
4. TROUBLE SHOOTING
4.1 Main Procedure

C
C
CT
T
TX
X
X Service Manual
S762A
12
St ar t
Power On
4.2 Power Circuit
Trouble shooting
No
Is indicator light?
I s backlight on?
Display performance OK?
O.S.D. Adjustment OK?
Audio Function OK ?
No Trouble Found
End
Yes
Yes
Yes
Yes
Yes
4.3 No Back light
Trouble shooting
4.4 Per for mance
Trouble shooting
4.5 O.S.D.
Trouble shooting
4.6 A udio
Trouble shooting
No
No
No
No
4.2 Power Circuit Trouble Shooting

C
C
CT
T
TX
X
X Service Manual
S762A
13
St ar t
End
Yes
Change display boar d
and retry
Change power boar d
and retry
Change AC power cord
and retry
No Tr ouble Found
End
OK
No
No
No
Back to 4.1
Main Procedure
No
4.3 Backlight Trouble Shooting

C
C
CT
T
TX
X
X Service Manual
S762A
14
St ar t
End
Yes
Change LCD panel
and retry
Change mai n boar d
and retry
Change power boar d
and retry
No Tr ouble Found
End
OK
No
No
No
Back to 4.1
Main Procedure
No
4.4 Performance Trouble Shooting

C
C
CT
T
TX
X
X Service Manual
S762A
15
Start
No
Screen missi ng col or
Block on screen
L i ne on screen
Scr een i s f l i ck er i ng
Screen whi t e
No Trouble
Found
End
YesYes
YesYes
Yes
OK
No
No
Change
VGA cable
Change
mai n board
OK
OK OK
OK OK
Change
LCD panel
Change
mai n board
Change
mai n board
Change
LCD panel
Change
power board
Change
mai n board
Change
LCD panel
Yes
OKOK
OK
No
Yes
Check panel
connector
Check mai n
board
connector
Change
LCD panel
Yes Yes Yes
OK
OKOK
Screen wi th noi se
& line bar
No
Press enter button call OSD
Menu try Reset or Auto Tune
Change
main board
Yes Yes
OK
OK
Yes Yes
4.5 O.S.D. Trouble Shooting

C
C
CT
T
TX
X
X Service Manual
S762A
16
St ar t
End
Yes
Change display boar d
and r et r y
Pr ess Fu nct i on k ey
No Tr ouble Found
No
No
No
No OSD M enu? Change M ain boar d
and r etr y
No Contrast or Bright
Adj Menu?
Change display boar d
and r et r y
Change M ain boar d
and r etr y
No
OK OK
OK OK
4.6 Audio Trouble Shooting

C
C
CT
T
TX
X
X Service Manual
S762A
17
St ar t
End
Yes
Change Speaker
No Tr ouble Found
No Sound? Change M ain boar d
and r etry
Sound is Broken Change Speaker
OK OK
OK
Make sure sound output,
Audio cable is OK.
Yes Yes
Yes
Volume can’t
Adiust
Change M ain boar d
and r et r y
OK

C
C
CT
T
TX
X
X Service Manual
S762A
18
PARTS LIST
ITEM PART NUMBER DESCRIPTION
1 AC1921-B01 MAIN PCBA
2 DC1725-B01 POWER PCBA
3 GC1921-B01 DISPLAY PCBA
4 10A17-4A2A LCD TFT 1280*1024 AU
5 SSBASE-509 SUB ASSY BASE
6 04008003000H CARTON
7 0510169800 HOLDER (R)
8 0510168800 HOLDER (L)
9 05Z0001900E PLASTIC HANDLE BAR
10 05Z0002900E PLASTIC CLAP BOARD
11 06208101000H USER MANUAL
12 65B70-1801ZH CABLE AUDIO
13 98T111-P61 DISKETTE 3.5IN 1.44M
14 65S10-150CZH CABLE SIGNAL

C
C
CT
T
TX
X
X Service Manual
S762A
19