Cura1 ActiveCare 3508 User manual

3508 - ActiveCare LED Pager
UM-046
Optional Accessories & Compatible Devices
(Sold Seperately)
2552 DoorAlert Door Strip, 2558 Wireless Call Button with
Pull Cord, 2573 Wristband Duress Transmitter, 2588
Personal Emergency Transmitter (PET), 2719 Cordless Pad
Transmitter, 2721 iBeam, 3502 ActiveCare Wireless Handset,
3503 Wireless Magnetic Door Switch,
3504 ActiveCare Bracket
*The range of wireless devices may vary and
be dependent on your specific environmental conditions.
cura¹ products are designed to augment well designed care
programs & practices, cura¹ does not claim that any of its products
are suitable as a substitute, or as a total solution for individuals that
require care and constant supervision & are at risk.
The cura13508 LED Pager is a versatile tool for a caregiver
in either a facility or home care environment. The Pager can
be paired with up to 3 compatible wireless devices.
Usage instructions
Setting Alarm Tone
There are 3 tones that can be selected. Press the
VOLUME button to toggle between these options:
1. Low tone with vibration alert.
2. Silent but with vibration alert.
3. High tone with vibration alert.
Alarms & Reset
When the alarm condition is active the pager will
vibrate and produce a continuous alarm tone (depending
on your VOLUME settings). The Device indicator LEDs
will indicate which device has the alarm condition and the
Status LED will blink red every 7 seconds until the pager
is reset.
To stop (reset) the alarm, press and hold the CANCEL
button for ~1 second.
Low Battery
Status LED flashes red.
VOLUME PROGRAM CANCEL
  
STATUS
Status LED
Device Indicator
LEDs. Pair with
(up to) 3 devices.
OPTION, MENU
and CANCEL
buttons.
ON / OFF
switch
Belt clip. Also fits
3504 Mounting
Bracket (optional).
ON OFF

1
2
QUICK START GUIDE
3508 - ActiveCare LED Pager Quick setup for use with cura1cordless pads,
mats and call buttons.
3
Rear View
Step
Insert 2 x AA Alkaline Batteries
Batteries: 3Vdc (2 x AA type)
Manufatured to ISO 9001, 13485
Tested and approved to IEC 60601-1-2 Medical Devices General
Part No.: 3508 www.cura1.com
Step
Enter Programming Mode
Batteries: 3Vdc (2 x AA type)
Manufatured to ISO 9001, 13485
Tested and approved to IEC 60601-1-2 Medical Devices General
Use a Phillips screwdriver to open the battery compartment and
insert two new AA alkaline batteries.
Replace cover and secure the screw.
Step
Clear the Pager memory
1. Ensure the pager ON / OFF selector switch is in the ON
position.
2. Press and hold the PROGRAM button until the status LED
turns solid green.
3. Release the PROGRAM button.
Note: the Pager will automatically exit Programming Mode
after successfully pairing or after 30 seconds.
5
Step
Test the pager prior to each use
To reset the Pager after an alarm, press and hold the
CANCEL button for ~1 second.
IMPORTANT: Test the operating range within your building
or work environment. Have someone repeatedly trigger the
device while you walk around the building. Note any areas
where the signal reception might be poor.
VOLUME PROGRAM CANCEL
  
STATUS
If the Pager has previously been programmed, there may not
be any memory slots left so it will be necessary to clear the
Pager’s memory before trying to program a new device into
a memory slot. To Clear the Pager Memory:
1. Hold down PROGRAM and CANCEL together for ~ 6
seconds. There will be 3 short beeps and the status light
will flash 3 times when the memory is cleared.
Trigger the monitored device (cordless pad, mat, call button
or other compatible device).
The pager should vibrate / sound alarm.
1. While the 3508 LED Pager is in Programming Mode (Step
3) trigger the first device. “Device 1” LED will flash twice to
acknowledge successful pairing.
2. For the second device, enter Programming Mode again
(Step 3) then trigger the second device. “Device 2” LED will
flash twice to acknowledge successful pairing.
3. For the third device, enter Programming Mode again (Step
3) then trigger the third device. “Device 3” LED will flash
twice to acknowledge successful pairing.
Note - for pairing with a 2719 Pad / Mat Transmitter, you do
not need to create an alarm condition in the Pad / Mat. To
pair with a 2719 Transmitter simply turn the Transmitter
from OFF to ON when the Pager is in Programming Mode.
Step
Pair with up to 3 Devices
4