Custom Dynamics GEN200-KIT-1157 Service manual

Have Questions? Call us at: 1 [phone] M-TH - 8:30AM-5:30PM EST / FR - 9:30AM-5:30PM
PN: GEN200-KIT-1157
Fits all Harley-Davidson® Models listed below:
2010-2013 Street Glide® and Road Glide® Custom, 2010-2011 Dyna® Street Bob and
Wide Glide, 2010 Soail® Converble CVO™ (models without a center taillight)
GEN-200-AW-1157 GEN-200-A-1157E3
We thank you for purchasing Custom Dynamics® LED turn
signal clusters! Our Genesis® LED’s offer maintenance free
service and higher visibility. We offer one of the best warranty
programs in the industry and we back our products with excel-
lent customer support, if you have questions before or during
installation of this product please call Custom Dynamics® at
1(800)382-1388.
Instructions
1. Remove lens from turn signal housings.
2. Remove bulbs from turn signal housings.
3. Be sure contacts are clean.
4. Insert base of LED cluster into housing making sure that
the alignment notches on the sides are properly oriented and
fully seated.
5. Twist cluster to coil wire and insert cluster into housing.
6. While holding cluster in place, reinstall lens.
NOTE: This product is designed for dual intensity front
turn signal fitment only. They will not function properly
in the rear.
LED Turn Signal Tips and Troubleshooting:
1. Dielectric grease does not need to be used with this
LED product, it can prevent them from working. Re-
move any excess from your turn signal sockets before
inserting.
2. Make sure you have the orientation correct before in-
serting the base. If it seems hard to twist in the socket, it
is probably in the wrong way.
3. Harley Davidson® Bullet turn signals may require trim-
ming of black gasket to fully seat lens.
4. Install the Smart Signal Stabilizer™ before testing Turn
signals.
5. If LED turn signal does not function correctly, clean the
bottom contacts, then re-insert. Also try in the other turn
signal socket.
Instructions
1. Remove lens from turn signal housings.
2. Remove bulbs from turn signal housings.
3. Be sure contacts are clean.
4. Insert base of LED cluster into housing making sure that
the alignment notches on the sides are properly oriented and
fully seated.
5. Twist cluster to coil wire and insert cluster into housing.
6. While holding cluster in place, reinstall lens.
NOTE: These products are designed for Rear turn signal
fitment only.
GEN2-SS6
Installation Instructions
This unit is alarm compatible and 4-way haz-
ard compatible. When using the 4-way hazards
with this product installed, the security key light on
the dash will come on. This is normal when in
hazard mode and will reset when turned off.
1. Make sure bike power is off.
2. Locate stock connector block for taillight/turn signals under
seat. If an aftermarket Run/Brake/Turn module is installed,
Smart Signal Stabilizer™ MUST go before Run/Brake/Turn
module.
3. Unplug main harness connector from fender harness
connector.
4. Plug Smart Signal Stabilizer™ in between these two con-
nectors.
5. Before turning power on, make sure the load switch on the
side of the stabilizer is in the “normal” position. (See next
page for Diagram).
6. Turn Ignition on, but do not start the bike. Activate the
right turn signal, allow to flash 2 times. Activate the left turn
signal, allow to flash 2 times. Activate the right turn signals
again for at least 10 flashes. Activate the left turn signal for
at least 10 flashes. Turn the ignition off and back on Check
the function of the turn signals.
GEN-200-R-1157 GEN-200-RR2-1157
11-2017

Installation Instructions - Page 2
11-2017
Custom Dynamics® Smart Signal Stabilizer™ Load Switch Diagram
Custom Dynamics®
Load Switch
Wires
Up Position:
(Away from wires)
Normal Load
Down Position:
(Toward wires)
High Load
7. Turn key on and test turn signals, running lights, and brake lights for proper operation. If you experience fast
flashing from the turn signals, turn the key off, move the recessed switch on the side of the stabilizer to the “high”
position (see diagram below). You can use a small screwdriver to move the switch to the down position. Repeat
steps 6 & 7.
8. Test the lights for proper operation for running lights, brake lights and turn signals before riding.
9. Test Alarm for proper operation, if equipped.
EVERYTHING to Light Up Your Ride®