CWT WCD00020B User manual

產品簡述:
低功率電波輻射性電機管理辦法
-第十二條:經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性
及功能。
-第十四條:低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼
續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機需忍受合法通信或工業、科學及醫療用電波輻射性電機
設備之干擾。
警告與安全資訊
使用產品之前， 請按照盒內手冊中的說明安裝與操作方式並閱讀所有安全資訊，以確保正確使用本產品。本產品可使用乾淨微濕軟布
清潔產品，但請勿把產品浸泡在水中清潔。
-請勿使產品受到外力衝擊或損壞。
-請勿將產品安裝在潮濕以及過度曝熱的場所。
-只限於在室內使用，溫度攝氏0度至35度之場所。
-請勿讓兒童或動物咀嚼或吞下產品。
-產品如有異常狀況，請勿自行拆解，應盡速送回經銷商進行維修服務。
使用問題排除:
1.為什麼將無線充電接收器放在桌上型無線充電發射器上方，都無任何充電反應?
-請確認是否有接上電源並且使用的是WCD00020B專用電源供應器。
-請確認接收器是否為WPC 相容產品。
-請確認發射器與接收器是否有接觸並且放置於適當位置。
2.為什麼無線充電會一直有重複感應的﹝嗶﹞聲音?
-若您的產品充電已達接近充飽電的時間點，有可能因您產品的電池老化或電流降低，造成發射端誤判。
此屬正常現象，可安心使用。此時建議您可以將您的產品移出。
-LED顯示燈，提醒產品開機並輔助夜間使用。
-符合WPC V1.1.2標準並具備異物偵測功能，安全更有保障。
-無線充電加雙規格USB充電口，可依不同設備需求進行充電。
-產品通過CE / FCC / NCC/BSMI/ 認證，使用更安心。
WCD00020B- 桌上型雙USB埠無線充電器
包裝內容物
規格&功能說明
僑威科技股份有限公司
地址:桃園市蘆竹區南崁路二段222號
輸出:
-USB :5V 1.0A
-USB :5V 2.1A
(USB充電支援BC 1.2規格)
※搭配CHANNEL WELL甜甜圈接收器(WCR01004B)
1. 將甜甜圈包裝內附送的EVA墊放置在手機裝置背後，支撐手機平衡。
2 將接收器放在CHANNEL WELL充電盤中間處，即可馬上進行充電。
CCAM15LP0790T0
客服專線:[phone]轉159
客服信箱:cwt_ser[email protected]
www.channelwell.com
Rev.A01
WCD00020B專用電源供應器
型號:ABL030F
輸入:110~240V 50-60Hz
輸出:12V 2.5A
開啟電源時，下方會有光
源提示本產品已開機。
使用須知與特點:
1. 如果被充電的裝置具備 規
範的接收器，可直接放置上方感
應區充電-會有﹝嗶﹞聲提醒。
2.請將無線充電接收器對準
圖示，充電效果較佳。
3.產品無線充電感應區具有貼心
的止滑設計。
型號:WCD00020B
輸入:12V 2.5A
輸出:無線充電支援 5V/1A
尺寸:Ø100*30mm
-桌上型雙USB埠無線充電器
(型號:WCD00020B)
-WCD00020B專用電源供應器
-中英文說明書。

-Table Top Wireless Transmitter.
(Model: :WCD00020B )
-Adapter for WCD00020B.
-User and Installation Manual (Chinese/ English) .
According to NCC Radio standard of Low Power electronic device:
Rule No. 12 : Any frequency band change, output power increase, or design change by the company, retailer, or user without
permission for the type-approved low power electronic device is forbidden.
Rule No. 14 : The operating of the low power electronic device should not generate interference to the flight safety or any
other legal communication ; If interference occurred, it must stop operating until the symptom is vanished. The legal com-
munication subjects to the wireless communication defined and instructed by the telecommunication law. The low power
electronic device must accept any interference caused by legal communication or ISM device.
WARNING:
In order to use correctly, please follow the instruction and installing manual.
To clean the charger, wipe with a moist cloth. Never submerge the charger in water.
-Avoid putting in moisture and overheat exposure space.
-Only charge devices which qi compatible or certified.
-Place the transmitter at the room temperature(0-35°C).
-Keep the device away from children and pets.
-Please contact supplier or the nearest retail store for product examination and repairs.
Channel Well Technology Co., Ltd
No.222, Sec. 2, Nankan Rd., Lujhu District,
Taoyuan City 338, Taiwan, R. O. C
Service TEL:[phone] ext 159
Email: cwt_ser[email protected]
1.Using with CHANNEL WELL’s wireless charging receiver.
2.Support the balance of your smartphone by using EVA Wedge.
3.Place it on the center of the wireless transmitter for recharge.
Product Features:
Issue to exclude:
1.Why is not any charge function when you put on the desktop wireless charger?
-Please ensure to connect the power and use our adapter.
-Please ensure the receiver is compatible with WPC .
-Please ensure both transmitter and receiver to connect and put the right location.
2.Why is the wireless charger with repeat “beep” noise?
-This is a normal condition, while your device is nearly to charge enough, or your battery is maturing, lower current to make
the transmitter misjudgment. We suggest removing your device.
-LED to display for “on” status and use at night.
-To meet WPC V1.1.2 with FOD function is more safety.
-You can charge different device with wireless power and dual USB ports.
-Certified by compliance: CE/FCC/NCC/BSMI/ .
WCD00020B-Table Top Wireless Transmitter
Packed Contents
Spec.and Technical Details
Output:
-USB :5V 1.0A
-USB :5V 2.1A
(USB support BC1.2 specification)
CCAM15LP0790T0
www.channelwell.com
Rev.A01
Adapter for WCD00020B
Model:ABL030F
Input:110~240V 50-60Hz
Output: 12V 2.5A
The high performance LED
light indicates the power of
wireless transmitter is on.
Notification to Use:
1. Your device with built-in
receiver, you can put direct on the
plate to charge with “beep” sound.
2.Please focus your wireless receiver
to get best charging effect.
3.Intimate skid proof design to
protect your device.
Model: WCD00020B
Input:12V 2.5A
Output:Wireless 5V/1A
Dimension:Ø100*30mm