CyberMed H24 Series User manual

CyberMed H24 Series
User Guide

i
FCC-B Radio Frequency Interference Statement
This equipment has been tested and found to comply with
the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
measures listed below.
•Reorient or relocate the receiving antenna.
•Increase the distance between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/television technician for help.
Notice 1 The changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
Notice 2 Shielded interface cables and A.C. power cord, if any, must be used in order
to comply with the emission limits.
Trademarks
All trademarks are the properties of their respective owners.
Intel® is a registered trademarks of Intel Corporation.
Windows® 7/Vista/XP/NT/2000/98/95 are registered trademarks of Microsoft Corporation.
Award® is a registered trademark of Phoenix Technologies Ltd.
AMI® is a registered trademark of American Megatrends Inc

ii
Safety Instructions
1. Always read the safety instructions carefully.
2. Keep this equipment away from humidity.
3. Lay this equipment on a reliable flat surface before setting it
up.
4. The openings on the enclosure are for air convection hence protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
5. Confirm the voltage of the power source and adjust accordingly to 110/220V
before connecting the equipment to the power inlet.
6. Place the power cord in such a way that it cannot be stepped on. Do not
place anything over the power cord.
7. Always unplug the Power Cord before inserting any add-on card or module.
8. All cautions and warnings on the equipment should be noted.
9. Never pour any liquid into the opening. This will cause damage and/or electrical
shock.
10. Do not disable the protective grounding pin from the plug. The equipment must be
connected to a grounded main socket/outlet.
11. The Optical Storage devices are classified as Class 1 Laser products. Use of controls or
adjustments or performance of procedures other than those specified is prohibited.
12. Do not touch the Laser lens inside the optical storage drive.
13. When installing the coaxial cable to the TV Tuner, it is necessary to ensure that the metal
shield is reliably connected to a protective earthing system of the building. Cable distribution
systems should be grounded (earthed) in accordance with ANSI/NF PA 70, the National
Electrical Code (NEC ), in particular, Section 820.93, Grounding of Outer Conductive Shield
of a Coaxial Cable.
14. If any of the following situations arise, have the equipment checked by authorized service
personnel:
•The power cord or plug is damaged.
•Liquid has penetrated into the equipment.
•The equipment has been exposed to moisture.
•The equipment has not worked well or you cannot get it working according to
the User's Guide.
•The equipment has been dropped and damaged.
•The equipment has obvious signs of breakage.
15. Do not attempt to remove or upgrade any component by yourself, any installation or
modification should be conducted by service personnel.
“Warning: If this equipment is modified, appropriate inspection and testing must be
conducted to ensure continued safe use of equipment”.
DO NOT LEAVE THIS EQUIPMENT IN AN UNCONDITIONED ENVIRONMENT WITH A
STORAGE TEMPERATURE ABOVE 50° C (122°F). IT MAY DAMAGE THE
EQUIPMENT.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by the manufacturer.

WEEE
(Waste
The W
E
retailer
s
sister D
i
Directiv
e
design
p
2005.
E
the cost
percent
a
Instructi
The sy
m
product
dispose
recyclin
g
recyclin
g
resourc
e
environ
m
for recy
c
or wher
e
Stateme
n
Electrical
a
E
EE directi
v
s
and impo
r
i
rective, R
O
e
by banni
n
p
hase. Th
e
E
U-based
m
s of recov
e
a
ges per t
h
ons for dis
m
bol show
n
must not b
of their wa
g
of waste
g
of your
w
e
s and ens
m
ent. For
m
c
ling, plea
s
e
you purc
h
n
t
a
nd Electro
n
v
e places a
r
ters to tak
e
O
HS (Rest
r
n
g the pres
e
e
WEEE Di
r
m
anufactur
e
e
ry from m
u
h
e WEEE r
e
p
osal of W
E
n
below is
o
e dispose
d
ste equip
m
electrical
a
w
aste equip
ure that it i
s
m
ore infor
m
s
e contact
y
h
ased the
p
n
ic Equip
m
n obligatio
n
e
-back ele
c
r
iction of H
a
e
nce of sp
e
r
ective cov
e
e
rs, distrib
u
u
nicipal col
l
e
quiremen
t
E
EE by Us
o
n the prod
u
d
of with ot
h
m
ent by han
a
nd electro
n
ment at th
e
s
recycled
m
ation abo
u
y
our local
c
p
roduct.
iii
m
ent)
n
on EU-b
a
c
tronics pr
o
a
zardous
S
e
cific haza
r
e
rs product
u
tors, retail
e
l
ection poi
n
t
s.
ers in the
E
u
ct or on it
s
h
er waste.
ding it ove
r
n
ic equipm
e
e
time of di
s
in a mann
e
u
t where y
o
c
ity office,
y
a
sed manu
f
o
ducts at th
S
ubstances
r
dous subs
t
s imported
e
rs and im
p
n
ts, reuse,
a
E
uropean
U
s
packagin
g
Instead, it
i
r
to a desig
n
e
nt. The s
e
s
posal will
e
r that prot
e
o
u can dro
p
y
our house
h
f
acturers,
d
e end of th
) complim
e
t
ances in t
h
into the E
U
p
orters are
o
a
nd recycli
U
nion
g
, which in
d
i
s the user’
s
n
ated colle
e
parate co
l
help to co
n
e
cts huma
n
p
off your
w
h
old waste
d
istributors,
eir useful li
e
nts the W
E
h
e product
s
U
as of Aug
u
o
bliged to f
i
ng of spec
i
d
icates tha
s
responsi
b
ction point
l
lection an
d
n
serve nat
u
n
health an
d
w
aste equi
p
disposal s
e
fe. A
E
EE
s
at the
u
st 13,
i
nance
i
fied
t this
b
ility to
for the
d
u
ral
d
the
p
ment
e
rvice

iv
TABLE OF CONTENTS
FCC-B Radio Frequency Interference Statement......................................................................i
Trademarks...................................................................................................................................i
Safety Instructions......................................................................................................................ii
WEEE Statement........................................................................................................................iii
Introduction.................................................................................................................................1
CyberMed H24 Series (H6)Specifications.................................................................................1
Processor Support ..................................................................................................................1
Motherboard Core Logic........................................................................................................ 1
Memory Support......................................................................................................................1
Networking...............................................................................................................................1
Audio.........................................................................................................................................1
Hard Disk Drive........................................................................................................................1
Mounting...................................................................................................................................2
LCD Panel.................................................................................................................................2
Expansion Slots.......................................................................................................................2
Front Lower Right Bezel .........................................................................................................2
Right Side Bezel.......................................................................................................................2
Left Side Bezel.........................................................................................................................2
Bottom I/O Panel.....................................................................................................................2
Power Supply...........................................................................................................................3
Dimensions ..............................................................................................................................3
Power Management....................................................................................................................8
Waking the System Up..........................................................................................................10
Energy Saving Tips ...............................................................................................................10
CyberMed H24 Series Overview…..………….………………………………………………………11
On Screen Display Buttons…………..………………………………………………………….….14
On Screen Display Usage.....................................................................................................15
System Assembly.....................................................................................................................19
Necessary Tools................................................................................................................... 19
Orientation of Key Parts........................................................................................................20
H24 Series Disassembly .......................................................................................................21
Installing the CPU..................................................................................................................23
Installing the CPU Heat Sink.................................................................................................24

v
Installing the Memory Module DDR3 SO-DIMM ..................................................................25
Installing the Hard Disk Drive...............................................................................................26
Installing the Optical Disk Drive...........................................................................................27
Installing the Mini-PCIe Card (Optional)..............................................................................29
Installing the Cover ...............................................................................................................30
Cybernet Recycling SOP…………………………………………………………………………….32
Figures
Figure 1: Front View with Optional Webcam………….………………………..……...…………11
Figure 2: Left side view with Optical Drive……………………………………………….……….12
Figure 3: Side USB Ports………………….…………………………………………..……..………13
Figure 4: Touch Panel and Power Button………..……..…………………………………….…..13
Figure 5: On Screen Display Buttons………..……..………………..…………………….….…..14
Figure 6: On Screen Display Usage……………………………………..…………….…………...15
Figure 7: Back view…....................................................................................................………16
Figure 8: Bottom Panel I/O Ports.............................................................................................16
Figure 9: CPU Heat Sink Ventilation Fan................................................................................17
Figure 10: SystemFans, CPU Heat Sink Fan and Ventilation................................................20
Figure 11: Open system..........................................................................................................22
Figure 12: Open system with GPU.........................................................................................22

H24 Series Page 1
Introduction
Congratulations for purchasing the H24 Series. The CyberMed H24 Series is your best
Slim LCD PC choice. With the fantastic appearance and small form factor, it can easily
be set anywhere. The feature packed platform also gives you an exciting PC experience.
CyberMed H24Series (H6) Specifications
Processor Support
3rd generation Intel® Core™i3, i5and Core™i7 in the1155package up to 35W.
Motherboard Core Logic
Intel® H61 Expresschipset (Sandy Bridge and Ivy Bridge)
Memory Support
DDR3 1066/1333 MHzSO-DIMM SDRAM (Un-buffered Non-ECC)
2DDR3 1333 MHzSO-DIMM slots (8GB Max)
Video & Graphics
Intel® integrated H61 Chipset with Intel® HD Graphics
Intel GMA HD/Intel Clear Video HD Technology
Built-in support for 1080p HD video playback, HDMI 1.4 & Blu-ray 3D support
Supports Microsoft®DirectX 10.1/DirectX 11, Shader Model 4.0 and OpenGL 3.0.
DVMT allocated as needed from 128MB to 1.70GB
Maximum display resolution 2560 x 1600.
Video & Graphics for dedicate Nvidia GPU
Onboard NVIDIA GeForce GT 540M(630M) GPU
1.0GB sDDR3 128-bit RAM
1080p HD video playback, HDMI 1.4 & Blu-ray 3D support.
Supports Microsoft®DirectX 11, Shader Model 5.0 and OpenGL 4.1
Maximum display resolution 2560 x 1600.
Networking
Supports 2PCI Express LAN 10/100/1000 Fast Ethernet by RealtekRTL8111E
Audio
2 internal speakers with 78dB+/-3dB @ 2.5W
HD Audio Codec Realtek® ALC892Flexible 10-channel audio with jack sensing,
Compliant with Azalia 1.0 Spec
Hard Disk Drive
One 2.5” SATA / SATA II Hard Disk Drive or SATA SSD - Any Capacity

H24 Series Page 2
Wall Mount
Support 75x75mm / 100x100mm VESA mounting hole, using M4 screw. 75 VESA can
support max screws length of 12mm; 100 VESA can support max screws length of
16mm.
Swivel Stand
System Base enables left/right rotation up to 60 degrees, tilt from -5 to 60 degrees.
LCD Panel
23.6"LEDwidescreen 16:9 format display (1920x1080).
Touch Screen
Ten-finger Multi-touch P-cap solution
Webcam
3.0 Megapixel Camera
Expansion Slots
Two mini-PCIe (One full size and one half size)
Wireless
Optional 802.11 b/g/n + Bluetooth or 802.11 a/b/g/n +Bluetooth
Front Lower Right Bezel
Power On/Off Buttons
Display On/Off Adjust
Contrast Adjust
Brightness Adjust
Right Side Bezel
Two USB 2.0 ports (for mouse and keyboard)
Left Side Bezel
Optional one optical disk drive – 2.5” slim or optional one additional 2.5” SATA
HDD/SSD.
Bottom I/O Panel
1 DC/IN port, 1 Serial port
1 DVI-I port, 1 HDMI port
2 LAN RJ-45, 2 USB3.0 ports, 2 USB2.0 ports
3 Audio jacks – Line in, Line Out and Mic in
4 TV Tuner ports - - Optional with TV Tuner (COAX Cable In, RCA Composite Video In,
Audio Left & Audio Right), 1 CMOS clear button, 1 Reset button

H24 Series Page 3
Power Supply
120 Watt Power Adapter from EDAC POWER ELECTRONICS CO., LTD, model
EM11011M, AC Input: 100~240V AC, 2.0-1.0A, 50-60Hz
DC Output: 19V, 6.31A 120W Max.
Or
120 Watt Power Adapter from EDAC POWER ELECTRONICS CO., LTD, model
EM11011H, AC Input: 100~240V AC, 2.0-1.0A, 50-60Hz
DC Output: 12V, 10.00A 120W Max.
Dimensions
598mm (H) x 420mm (W) x 262mm (D)(with stand)
598mm (H) x 377mm (W) x 55mm (D)(without stand)

H24 Series Page 4
Intended use
The H24 Series is designed for general pc application purpose for hospital environment
and for diagnosis. It could be used for Radiology, PACS (Picture Archiving
Communication Systems),LIS (Lab Information Systems) and Electronic Medical
Recordpurpose. It shall not be used for life-supporting system.
WARNING: Critical diagnostic decision must not be based solelyon images displayed by
this device.
Unpacking
After opening the carton, there is the LCD PC with an accessory box. Check carefully to
see if there are any damages ormissing parts.
Read the Manual
Please read this manual carefully and remember to keep thismanual for future reference.
Safety Instructions & Cleaning
This product has undergone various tests in order to comply withsafety standards.
Inappropriate use or open the housing may bedangerous. Please remember to follow the
instructions below toensure your safety during the installation and operating process.
Transporting & Placement of unit
1. When moving the unit on a cart; be very cautious. Quickstops, excessive forces and
uneven surfaces may causethe cart to overturn thus risking the unit to fall to the
ground.
2. If the LCD PC unit does fall to the ground,immediately turn the power off and
disconnect cords. Thencontact a service technician for repairs. Continual use of
the unit may result cause a fire or electric shock. Also, donot repair the unit on your own.
3. Having two or more people transporting the LCD PC unit is recommended. In addition,
when installing theunit by suspending it also requires two or more people.
4. Before suspending the unit, make sure the material usedfor suspension is sturdy and
stable. If not properly suspended, the LCD PC unit may fall and causeserious injury to
people standing nearby as well as to theunit itself.
5. If the user wishes to mount the LCD PC unit, rememberto use only the mounting
hardware recommended by themanufacturer.

H24 Series Page 5
Electrical and Power Source Related
1. This LCD PC unit must operate on a power sourceas shown on the specification label.
If you are not surewhat type of power supply used in the area, consult yourdealer or local
power supplier.
2. The power cords must not be damaged. Applied pressure,added heat, and tugging
may damage the power cord.
3. The power cord must be routed properly when setup takesplace. We advise that this
aspect measure is to preventpeople from stepping on the cords or while the unit
issuspended to prevent flying objects from getting tangledwith the unit.
4. Do not overload the AC outlets or extension cords.Electrical shocks or fires may occur
from overloading.
5. Do not touch the power source during a thunderstorm.
6. If your hands are wet, do not touch the plug.
7. Use your thumb and index finger, grip firmly on the powercord to disconnect from the
electrical socket. By pulling thepower cord, may result in damaging it.
8. If the unit is not going to be in use for an extended periodof time, remember to
disconnect the unit.
9. The LCD PC unit uses 19V DC output from an adapter. Connect the unit to a power
source with the same numerical value as indicated. Please use only the powercord
provided by the dealer to ensure safety and EMCcompliance.
WARNING:To avoid risk of electric shock, this equipment must only be connected to a
supply mains with protective earth.
Disconnect Device
1. To fully disengage the power to the unit, please disconnect the power cord from the AC
inlet.”
Various Factors of Environment
1. Operating Temperature: 0°C to 50°C; Non-operating temperature: -20°C to 60°C.
2. Operating Humidity (Non-Condensing): 10% to 90%. Non-operating Humidity
(Non-condensing): 10% to 90%.
3.Do not insert objects into the openings.

H24 Series Page 6
4. Do not have liquids seep into the internal areas of the LCD PC unit.
5. Having liquids seep in or inserting objects into the unitmay result in electric shocks from
taking and/or shortcircuiting the internal parts.
6. Do not place the LCD PC unit in the presence ofhigh moisture areas.
7. Do not install the LCD PC unit in a wetenvironment.
8. Do not place unit near heat generating sources.
9. Do not place the unit in a location where it will come incontact with fumes or steam.
10. Remember to keep the LCD PC unit away fromthe presence of dust.
11. If water has flow in or seep in, immediately disconnect theopen frame unit. Then
contact a service technician forrepairs.
Ventilation Spacing
1. Do not cover or block the openings on the top and back sides of the LCD PC unit.
Inadequate ventilationmay cause overheating thus reducing the lifespan of theunit.
2. Unless proper ventilation is present, do not place unit in anenclosed area; such as a
built-in shelf. Keep a minimumdistance of 10 cm between the LCD PC unit andwall.
Cleaning the unit
1. Remember to turn off the power source and to unplug thecord from the outlet before
cleaning the unit.
2. Carefully dismount the unit or bring the unit down fromsuspension to clean.
3. Please use a dry soft cloth to clean the unit.
4. Take a dry cloth and wipe the unit dry. Remember to avoidhaving liquids seep into the
internal components and areas of the LCD PC unit.
Servicing, Repairing, Maintenance & Safety Checks
1. If the unit is not functioning properly, observe theperformance level of the LCD PC
closely todetermine what type of servicing is needed.
2. Do not attempt to repair the LCD PC unit on yourown. Disassembling the cover
exposes users’ to highvoltages and other dangerous conditions. Notify andrequest a
qualified service technician for servicing the unit.

H24 Series Page 7
3. To avoid risk of electric shock, this equipment must only beconnected to a supply
mains with protective earth.
4. If any of the following situations occur turn the powersource off and unplug the unit.
Then contact a qualifiedservice technician.
(a) A liquid was spilled on the unit or objects have falleninto the unit.
(b) The unit is soaked with liquids.
(c) The unit is dropped or damaged.
(d) If smoke or strange odor is flowing out of the operatingunit.
(e) If the power cord or plug is damaged.
(f) When the functions of the unit are dysfunctional.
5. When replacement parts are needed for the LCD PC unit, make sure service
technicians use replacementparts specified by the manufacturer, or those with thesame
characteristics and performance as the originalparts. If unauthorized parts are used it
may result instarting a fire, electrical shock and/or other dangers.
ISO 7000-0434: Caution, consult ACCOMPANYING DOCUMENTS.
ISO 7000-1641: Follow operating instructions or Consult instructions
for use.
IEC 60417 -5009: ready to use.
IEC 60417-5031: Direct current.
EU-wide legislation, as implemented in eachMember State, requires
that waste electrical andelectronic products carrying the mark (left)
must bedisposed of separately from normal householdwaste. This
includes monitors and electricalaccessories, such as signal cables or
power cords.When you need to dispose of your medical panel
PCproducts, please follow the guidance of your localauthority, or ask
the shop where you purchased theproduct, or if applicable, follow any
agreementsmade between yourself.The mark on electrical and
electronic products onlyapplies to the current European Union
MemberStates.

H24 Series Page 8
Power Management
Power management of LCD-PC has the potential to save significant amounts of electricity
as well as deliver environment benefits.
To be energy efficient, turn off your display or set your LCD-PC to sleep mode after a
period of user inactivity.
Power Management in Windows OS
[Power Options] in Windows OS allow you to control the power management features of
your display and hard drive. Go to [Start] > [Control Panel].
Then click on the [Power Options] link.

H24 Series Page 9
Select a power plan that suits your personal needs. You may also fine-tune the settings
by clicking [Change plan settings].
The Shut Down LCD-PC Menu presents the options of Sleep (S3) & Shut Down (S5) for
rapid and easy management of your system power.

H24 Series Page 10
Power Management through ENERGY STAR qualified Monitors (Not
supply with the LCD PC)
The power management feature allows the LCD-PC to initiate a low-power or “Sleep”
mode after a period of user inactivity. When used with an external ENERGY STAR
qualified Monitor, this feature also supports similar power management features of the
monitor. To take advantage of these potential energy saving, the power management
feature can be set to behave in the following ways when the system is operating on AC
power:
•Turn off the display after 15 minutes.
•Initiate Sleep after 30 minutes.
Waking the System Up
The LCD-PC shall be able to wake up from power saving mode in response to a
command from any of the following:
•the power button,
•the network (Wake on LAN),
•the mouse
•the keyboard
Energy Saving Tips:
•Tune the settings in Power Options under Windows OS to optimize your LCD-PC’s
power management.
•Install power saving software to manage your PC’s energy consumption.
•Always disconnect the AC power cord or switch the wall socket off if your LCD-PC
would be left unused for a certain time to achieve zero energy consumption.

H24 Series Page 11
CyberMed H24 Series Overview
Figure 1: Front View with Optional Webcam

H24 Series Page 12
Figure 2: Left side view with Optical Drive

H24 Series Page 13
Figure 3: Side USB Ports
Figure 4: Touch Panel and Power button
“ready to use button”

H24 Series Page 14
On Screen Display Buttons
Figure 5: On Screen Display Buttons
There are four buttons on the lower bezel of the screen. From right to left they are:
OSD key Response time Function
Ready to useDelay 1.5 sec On/off Power
Privacy
button immediately
1. Turn off the display.
2. Turn on the display.
Contrast / + Immediately
Turn on the Contrast adjustment On display
Continuous send out pulse when user’s finger
keeps pressing the button and increase the
value
Brightness / -Immediately
Turn on the Brightness adjustment on display
Continuous send out pulse when user’s finger
keeps pressing the button and increase the
value