CyberPower OLS6000E User manual

Userˊs Manual
OLS6000E(XL)
OLS10000E(XL)
CyberPower Systems Inc.
www.cyberpower.com
K01-C000044-06

CONTENT：
1. Safety .................................................................................................................1
1.1. Installation ..................................................................................................1
1.2. Operation....................................................................................................1
1.3. Maintenance, Servicing and Faults.............................................................2
1.4. Transport ....................................................................................................3
1.5. Storage .......................................................................................................3
1.6. Standards ...................................................................................................3
2. Description of Commonly Used Symbols.......................................................4
3. Introduction .......................................................................................................4
3.1. Feature .......................................................................................................5
3.2. Electrical Specifications ..............................................................................6
3.3. Operating Environment...............................................................................7
3.4. Dimensions and Weights ............................................................................7
4. Installation .........................................................................................................8
4.1. Unpacking...................................................................................................8
4.2. Power Wires Installation .............................................................................8
4.3. External Battery Pack Connecting Procedure .........................................11
4.4. EPO Connection .......................................................................................12
5. Operation .........................................................................................................13
5.1. Display Panel............................................................................................13
5.2. Turning On and Turning Off UPS..............................................................15
5.3. LCD Operation..........................................................................................16
6. Special Function .............................................................................................21
6.1. ECO Function ...........................................................................................21
6.2. Converter Function ...................................................................................21
6.3. Parallel Function .......................................................................................22
7. Trouble Shooting ............................................................................................26
7.1. Trouble Shooting According to Warning Indication ...................................26
7.2. Trouble Shooting According to Fault Indication ........................................28
7.3. Trouble Shooting in Else Cases................................................................29
8. Battery Maintenance .......................................................................................30
9. Communication Port.......................................................................................31
9.1. USB Interface ...........................................................................................31

9.2. Dry contact Interface(optional) .................................................................31
9.3. RS232 Interface........................................................................................31
9.4. Intelligent slot............................................................................................31

1
1. Safety
Please read carefully the following user manual and the safety instructions
before installing the unit or using the unit!
1.1. Installation
This is permanently connected equipment, and it must be installed by qualified
maintenance personnel.
Condensation may occur if the UPS is moved directly from a cold to a warm
environment. The UPS must be absolutely dry before being installed. Please
allow an acclimatization time of at least two hours.
Do not install the UPS near water or in damp environment.
Do not install the UPS where it would be exposed to direct sunlight or near heat.
Do not connect appliances or items of equipment which would overload the UPS
(e.g. laser printers, etc.) to the UPS output.
Do not block ventilation openings in the UPS’s housing. Ensure allow at least
0.5m of space on front and rear of the UPS.
Place cables in such a way that no one can step on or trip over them.
Connect UPS with the earth reliably before connecting to the building wiring
terminal, and external battery source must also be earthed.
An integral single emergency switching device which prevents further supply to
the load by the UPS in any mode of operation should be provided in the building
wiring installation.
An appropriate disconnect device as short-circuit backup protection should be
provided in the building wiring installation.
The equipment is powered by two sources: the mains source, the internal
battery or the external battery source.
With the installation of the equipment, the sum of the leakage current of the UPS
and the connected load does not exceed 5% of rated value of input current.
1.2. Operation
Do not disconnect the main cable on the UPS or the building wiring terminals
during operation since this would remove the protective earth from the UPS and
all connected loads.
The UPS output terminal block may still be electrically lived even if the UPS is

2
not connected to the building wiring terminal, for there is internal current source
(batteries).
In order to fully disconnect the UPS, first turn the input breaker in the "OFF"
position, then disconnect the mains lead.
Indiscriminate operation of switches may cause output loss or damage to
equipment. Refer to instruction before conducting any control.
While the UPS work as a parallel system, the external parallel cable should be
reinforced insulation.
Ensure that no liquid or other foreign objects can enter the UPS.
1.3. Maintenance, Servicing and Faults
Do not remove the enclosure since the UPS operates with hazardous voltages.
It is to be serviced only by qualified maintenance personnel.
Caution! Risk of electric shock. Even after the unit is disconnected from the
mains power supply (building wiring terminal) components inside the UPS are
still connected to the battery which are potentially dangerous.
Before carrying out any kind of service or maintenance, isolate UPS and
disconnect the batteries. Verify that no current is present and no hazardous
voltage exists in the capacitor or BUS capacitor.
Batteries must be replaced only by qualified personnel.
Batteries have a high short-circuit current and pose a risk of shock. Take all
precautionary measures specified below and any other necessary measures
when working with batteries:
─ remove all jewellery, wristwatches, rings and other metal objects
─ use only tools with insulated grips and handles.
When changing batteries, replace with the same quantity and the same type of
batteries.
Do not attempt to dispose of batteries by burning them. It could cause explosion.
The UPS may be connected to external battery package. Proper disposal of
batteries is required. Refer to your local codes for disposal requirements.
Do not open or destroy batteries. Effluent electrolyte can cause injury to the skin
and eyes. It may be toxic.
Replace the fuse only by a fuse of the same type and of the same spec in order
to avoid fire hazards.

3
1.4. Transport
Please transport the UPS only in the original packaging to protect against shock
and impact.
1.5. Storage
The UPS must be stockpiled in the room where is ventilated and dry.
1.6. Standards
* Safety
IEC/EN 62040-1
* EMI
Conducted Emission................................:IEC/EN 62040-2
Category C3
Radiated Emission...................................:IEC/EN 62040-2
Category C3
*EMS
ESD....................................................... ..:IEC/EN 61000-4-2
Level 3
RS............................................................:IEC/EN 61000-4-3
Level 3
EFT..........................................................:IEC/EN 61000-4-4
Level 4
SURGE....................................................:IEC/EN 61000-4-5
Level 4
Low Frequency Signals............................:IEC/EN 61000-2-2
Warning: This is a product for commercial and industrial application in the
second environment-installation restrictions or additional measures may be
needed to prevent disturbances.

4
2. Description of Commonly Used Symbols
Some or all of the following symbols may be used in this manual. It is advisable to
familiarize yourself with them and understand their meaning:
3. Introduction
This On-Line series is an uninterruptible power supply incorporating
double-converter technology. It provides perfect protection specifically for computer
equipments, communication servers, and data centers.
The double-converter principle eliminates all mains power disturbances. A rectifier
converts the alternating current from the mains power to direct current. On the
basis of this DC voltage, the inverter generates an AC sinusoidal voltage, which
constantly supplies the loads. In the event of power failure, the maintenance-free
batteries power the inverter.
This manual covers the UPS listed as follows. Please confirm whether it is the
model you intend to purchase by performing a visual inspection of the Model No. on
the rear panel of the UPS.
Symbol and Explanation
Symbol
Explanation
Symbol
Explanation
Alert you to pay
special attention
Caution of high
voltage
Alternating current
source(AC)
Direct current
source(DC)
Turn on or turn off
the UPS
Protective
ground
Recycle
Do not dispose
with ordinary
trash

5
Model NO.
Type
Model NO.
Type
OLS6000E
Standard
OLS6000EXL
Extended backup time
OLS10000E
OLS10000EXL
" XL" Model: Extended backup time.
OLS6000E(XL) OLS10000E(XL)
Fig.3-1 The rear view of OLS6000E(XL)/OLS10000E(XL)
3.1. Feature
This series UPS is a new generation of UPS, which provides the outstanding
reliability, and most cost-performance ratio in the industrial. Following benefit the
product has:
True online double-conversion technology with high power density, frequency
independence and generator compatibility.
High input power factor ≥0.99,overall high efficiency ≥92%, save power
and wiring expense. Low input current distortion, avoid power pollution.
Output power factor is 0.9, perfect output sine waveform, suitable almost all
critical equipment.
Outstanding adaptability to the worst mains input condition. Extra wide input
voltage, frequency range and waveform, avoid excessive dissipating limited

6
battery energy.
Internal charger of XL model could be up to 4Amps to decrease recharging
time of battery.
N+X parallel redundancy to increase the reliability and flexibility. Number of
parallel operating UPS is up to 4.
ECO mode with high efficiency ≥96%, save power expense for user.
Start-able without battery.
3.2. Electrical Specifications
Input
Model NO.
OLS6000E(XL)
OLS10000E(XL)
Phase
Single
Voltage Range
110~276Vac(Depends on load level)
Frequency Range
(45~55)/(54~66)Hz
Rated Current
31(36)A
50(55)A
Power Factor
≥0.99 @ full load
Battery
Rated Voltage
240Vdc
Rated Current
28A
47A
Output
Model NO.
OLS6000E(XL)
OLS10000E(XL)
Power Rating
6kVA/5.4kW
10kVA/9kW
Voltage*
208/220/230/240Vac
Frequency
Synchronized 50/60×(1±10%)Hz @Line mode
50/60×(1±0.1%)Hz @Battery mode
Wave Form
sine

7
Load Type
PF 0.5~1, lagging
THDV
≤2% @ full linear load
≤5% @ full nonlinear load
Overload**
In Line mode:
10 min 105~125%
1 min 125~150%
10 s >150%
100 ms >170%
In Battery mode:
2 min 105~125%
30 s 125~150%
100 ms >150%
*The load capacity would be derated to 90% automatically when the output voltage
is adjusted to 208Vac.
**The overload capacity would be derated automatically in Line mode while the
circumstance temperature is larger than 35 degree.
3.3. Operating Environment
Temperature
Humidity
Altitude
Storage temperature
0℃~40℃
<95%
<1000m
-15℃~50℃
Note: The load capacity should be derated 1% every 100m heightened on the
basis of 1000m.
3.4. Dimensions and Weights
Model NO.
Dimensions W×H×D(mm)
Net Weight (kg)
OlS6000E
260×708×550
70
OLS6000EXL
260×708×550
25
OLS10000E
260×708×550
86
OLS10000EXL
260×708×550
28

8
4. Installation
The system must be installed and wired only by qualified electricians in
accordance with applicable safety regulations!
For safety, please cut off the mains power switch before installation!
When installing the electrical wiring, please note the nominal amperage of your
incoming feeder.
4.1. Unpacking
A UPS
A user’s manual
A USB cable
A RS232 cable (optional)
A parallel cable
A parallel port cover plate
Terminal splices 12pcs (using for the wire connection on input terminal)
*PowerPanel® Business Edition software is available on our website. Please
visit www.cyberpower.com and go to the Software Section for free download.
CAUTION! Inspect the appearance of the UPS to see if there is any damage during
transportation. Do not turn on the unit and notify the carrier and dealer immediately
if there is any damage or lacking of some parts.
4.2. Power Wires Installation
4.2.1. Notes for installation:
1) The UPS must be installed in a location with good ventilation, far away from
water, inflammable gas and corrosive agents.
2) Ensure the air vents on the front and rear of the UPS are not blocked. Allow at
least 0.5m of space on each side.
3) Condensation to water drops may occur if the UPS is unpacked in a very low
temperature environment. In this case it is necessary to wait until the UPS is fully
dried inside out before proceeding installation and use. Otherwise there are
hazards of electric shock.

9
4.2.2. Installation
Use cable cross section and protective device specification ：
Model
OLS6000E(XL)
OLS10000E(XL)
Protective earthing conductor
Min cross section
6mm²
(UL1015 10AWG)
10 mm²
(UL1015 8AWG)
Input L, N
Min conductor cross section
6mm²
(UL1015 10AWG)
10 mm²
(UL1015 8AWG)
Input breaker
40A/250Vac
63A/250Vac
Output L,N, Jumper(J1-J2)
Min conductor cross section
6mm²
(UL1015 10AWG)
10 mm²
(UL1015 8AWG)
External Battery Cabinet
Positive Pole(+), Negative pole(-),
Min conductor cross section
6mm²
(UL1015 10AWG)
10 mm²
(UL1015 8AWG)
External Battery Cabinet Fuse
in Positive Pole(+), Negative pole(-)
30A/240Vdc
60A/240Vdc
External Battery Cabinet Breaker in
Positive Pole(+), Negative pole(-)
32A/240Vdc
60A/240Vdc
Torque for fixing above terminals
3.95~4.97Nm (35~44 1b in)
1) It is suggested to install an external isolating device against current backfeed
between mains input and UPS. After the device is installed, it must add a
warning label with the following wording or the equivalent on the external AC
contactor: RISK OF VOLTAGE BACKFEED. Isolate the UPS before operating
on this circuit, then check for hazardous voltage between all terminals.
AC Contactor
Coil Remotes Swith
Mains
Input
Input Mains
Breaker
L
N
UPS
Fig.4-1 Typical external isolating device installation

10
2) No matter the UPS is connected to the mains power or not, the output of the
UPS may be electrically live. The parts inside the unit may still have hazardous
voltage after turning off the UPS. To make the UPS have no output, turn off the
UPS, and cut off the mains power supply, wait the UPS shut down completely,
finally cut off the battery connection.
3) Open the terminal block cover located on the rear panel of UPS, please refer
to the appearance diagram.
4) For OLS6000E(XL), it is recommended to select the UL1015 10AWG (6mm²)
or other insulated wire which complies with AWG Standard for the UPS input
and output wirings.
5) For OLS10000E(XL), it is recommended to select the UL1015 8AWG (10 mm²)
or other insulated wire which complies with AWG Standard for the UPS input
and output wirings.
6) Ensure the capacity of mains power supply. Do not use the wall receptacle as
the input power source for the UPS, as its rated current is less than the UPS’s
maximum input current. Otherwise the receptacle may be burned and
destroyed.
7) The protective earth ground wire should be installed first according to the
following diagram. It is better to use green wire or green wire with yellow ribbon
wire.
8) Connect other input and output wires to the corresponding input and output
terminals according to the following diagram.
Input Ground
Input N
Input L
Battery+
Battery-
Battery Ground
Output Ground
Output L
Output N
Parallel Jump 2
Parallel Jump 1
N L + - J1 J2 N L
INPUT BATTERY JUMPER OUTPUT
Fig.4-2 Input and output Terminal Block wiring diagram
Note: Make sure that the input and output wires and the input and output terminals
are connected tightly.

11
9) It is requested to use the accessorial terminal splices which can be compacted
on the wires tightly, to ensure the connection between the wires and the
terminal block is reliable.
10) Install an output breaker between the output terminal of UPS and the load, and
the breaker should be with leakage current protective function if necessary.
11) Turn off all the loads first before connecting the load with the UPS, then
perform the connection and finally turn on the loads one by one.
12) After completing the installation, please check the wires to make sure all were
connected correctly and tightly.
13) Suggest charging the batteries for 8 hours before use. After Installation, turn
on the mains power switch and turn the input breaker in the "ON" position, the
UPS will charge the batteries automatically. It can also use the UPS
immediately without charging the batteries, but the backup time may be less
than the standard value.
14) If it is necessary to connect the inductance load such as a monitor or a laser
printer to the UPS, the start-up power should be used for calculating the
capacity of the UPS, as its start-up power consumption is too big to make the
UPS which capacity is small fail easily.
4.3. External Battery Pack Connecting Procedure
1. The nominal DC voltage of external battery pack is 240Vdc. To achieve longer
backup time, it is possible to connect multi-battery packs, but the principle of
"same voltage, same type" should be strictly followed.
2. For OLS6000E(XL), select the UL1015 10AWG (6mm²) respectively or other
insulated wire which complies with AWG Standard for the UPS battery wirings.
3. For OLS10000E(XL), select the UL1015 8AWG (10mm²) respectively or other
insulated wire which complies with AWG Standard for the UPS battery wirings.
4. The external battery pack must be independent for each UPS. It is forbidden
that two UPS use one external battery pack.
5. The procedure of installing battery pack should be complied with strictly.
Important notes:
If the UPS is used in single mode, J1 and J2 must be connected.
If the UPS is used in parallel mode, the Jumper between J1 and J2 must be
removed.

12
Otherwise it may encounter the hazardous of electric shock.
1) Ensure the UPS is not powered on and the mains input breaker is set in the
"OFF" position.
2) A DC breaker must be installed between the external battery pack and the
UPS. The capacity of breaker must be not less than the data specified in the
general specification.
3) Set the external battery pack breaker in "OFF" position and connect the 20
pieces of batteries in series.
4) Connect the external battery pack to the battery terminals. Check the
polarity of connection is correct.
5) Set breaker of the battery pack in the "ON" position.
6) Set the mains input breaker in the "ON" position, the UPS would power on
and start to charge the battery pack.
4.4. EPO Connection
EPO (Emergency power off): when the emergency occurs, such as the failure of
load, the UPS can cut off the output at once by operating the EPO port manually.
The connection ：
Normally the EPO connector is closed with a wire on the rear panel, which is
supplied in the accessory. Once the connector is open, the UPS would stop the
output and enter EPO status (Fig.4-3).
Fig.4-3 Enable the EPO status Fig.4-4 Disable the EPO status
To recover to normal status, first EPO connector should be closed (Fig.4-4), and
enter LCD menu (illustrated in the chapter of 5.3) to clear EPO status, then UPS
would stop alarm and recover to Bypass model. And UPS needs be turned on by
manual operation.

13
5. Operation
5.1. Display Panel
The UPS has a five-button, dot matrix LCD with white text and a blue background.
Besides the LCD, the UPS has four colorized LED to provide more convenient
information.
Fig.5-1 LCD Panel
Control button functions ：
The
Button
Function
illustration
Power on
When the unit is no power and has connected with battery,
press this button more than 200ms to power on
Turn on
When the unit is powered on and is in Bypass mode, press
this button more than 1s to turn on
Turn off
When the unit has been turned on, press this button more
than 3s to turn off
Enter
Press this button more than 200ms to confirm current
selection or enter the current selection window
ESC
Exit
Press this button more than 200ms to cancel current
selection and return to previous menu
UP
Press this button more than 200ms to move the focus to the
up menu
Down
Press this button for more than 200ms to move the focus to
the down menu

14
LED definition:
Note：
〇: Lightened constantly；※: #1-#4 Lightened circularly
★: Flashing；□: Depended on the fault/warning status or other status
Alarm definition:
The UPS provides useful information about UPS itself, load status, battery, events,
identification, and settings through the front panel display.
UPS state
NORMAL
(Green LED)
BATTERY
(Yellow LED)
BYPASS
(Yellow LED)
FAULT
(Red LED)
Bypass mode with no
output
★
□
Bypass mode with
output
〇
□
Line mode
〇
□
Battery mode
〇
〇
□
ECO mode
〇
〇
□
Battery test mode
※
※
※
※
Turn on
※
※
※
※
Fault mode
□
〇
Warning mode
□
□
□
★
UPS condition
Buzzer status
Fault active
Continuous
Warning active
Beep every second
Battery mode
Beep every 4 seconds, if battery low, buzzer Beep every second
Bypass mode
Beep every 2 minutes
Overload
Beep twice every second

15
During powering on, the LCD would display the CyberPower logo for several
seconds and then enter to the default page which shows the UPS status summary.
On the UPS status screen it provides the following information:
Status summary, including mode, load, battery and utility
Alarm status, if any is present.
Fault status, if any is present.
Output parameter, including output voltage, current and frequency.
Input parameter, including input voltage and frequency.
Bypass parameter, including bypass voltage and frequency.
Power parameter, including output VA and watt.
Battery parameter, including battery capacity, voltage and remain time.
5.2. Turning On and Turning Off UPS
Attention: The UPS could only be turning on while connecting with the mains at
the first time.
Attention: Please switch off the connected loads first before turning on the UPS,
and switch on the loads one by one after the UPS is turned on. Switch off all of the
connected loads before turning off the UPS.
Turning on UPS with mains ：
1) Check all the connection is correct. Check the breaker of external battery pack
is in "ON" position.
2) Set input breaker in "ON" position. At this time the fan begins to rotate, LCD
will show "CyberPower". Then LCD will show the default UPS status summary
screen after UPS finishing self-test.
3) By pressing button continuously for more than 1 second，the buzzer will
beep for 1s, UPS starts to turn on.
4) A few seconds later, the UPS turns into Line mode. If the mains power is
abnormal, the UPS will transfer to Battery mode without output interruption of
the UPS.
Turning on UPS without mains ：
1) Check all the connection is correct. Check the breaker of external battery pack
is in "ON" position.
2) By pressing button continuously for more than 200ms, the UPS would be
powered on. At this time the fan begins to rotate, LCD will show "CyberPower".

16
Then LCD will show the default UPS status summary screen after UPS
finishing self-test.
3) By pressing button continuously for more than 1 second，the buzzer will
beep for 1s, UPS starts to turn on.
4) A few seconds later, the UPS turns into Battery mode. If the mains power
comes back, the UPS will transfer to Line mode without output interruption of
the UPS.
Turning off UPS with mains ：
1) To turn off the inverter of UPS by pressing button continuously for more
than 3s and the buzzer will beep for 3s. The UPS will turn into Bypass mode at
once.
2) When completing the above action, UPS output voltage is still present. In order
to cut off the UPS output, simply cut off the mains power supply. A few
seconds later, LCD display shuts down and no output voltage is available from
the UPS output terminal.
Turning off UPS without mains ：
1) To power off the UPS by pressing button continuously for more than 3s,
and the buzzer will beep 3s. The UPS will cut off the output at once.
2) A few seconds later, LCD shuts down and no voltage is available from the UPS
output.
5.3. LCD Operation
Except the default UPS status summary screen, the user could get more useful
information about UPS current status, old events which ever occurred, UPS own
identification, and could change the settings to fit the user own requirements,
optimize the function of UPS.

17
Fig.5-2 UPS status menu
Load: 60 %
I/P Volt: 223.5 V
Bat Volt: 260 V
Status:Line
Output parameter
Volt: 230 V
Curr: 14.5 A
Freq: 50.0 Hz
Input parameter
Volt: 223.5 V
Freq: 50.1 Hz
Bypass parameter
Volt: 223.5V
Freq: 50.1Hz
Power parameter
KW: 3.3
KVA:3.6
Bat parameter
Bat Volt: 260V
Capacity: 95 %
Rmn time 14 Min
Cyberpower
Alarm
0002:12:00:00
Overload
1/10
Fault
0003:12:00:00
Over tempearture
1/5
Down>200mS Up>200mS
Down>200mS Up>200mS
Down>200mS Up>200mS
Down>200mS Up>200mS
Down>200mS Up>200mS
Down>200mS Up>200mS
Down>200mS
Up>200mS
Alarm
0002:12:20:00
Line site
2/10
Enter>200mS
ESC>200mS
Alarm
0002:12:00:00
Overload
1/10
Up>200mS Down>200mS
Fault
0003:12:00:00
Over tempearture
1/5
Enter>200mS
ESC>200mS
Cable loss
0003:12:00:00
Over tempearture
2/5
Up>200mS Down>200mS
Up>200mS Down>200mS
.
.
.
Up>200mS Down>200mS
Control
Setting
Events
ID
ESC>200mS
ESC>200mS