CyberPower OR1500LCDRTXL2U User manual

INTELLIGENT UPS SERIES
OR1500LCDRTXL2U / OR2200LCDRTXL2U
USER MANUAL
YOUR ULTIMATE ALLY IN POWER
Cyber Power Systems (USA), Inc.
4241 12th Avenue East, Suite 400 | Shakopee, MN 55379 | CyberPowerSystems.com
FEATURES
1. Power Switch
2. Power On Indicator (Blue)
3. LCD Module Display
4. LCD Function Selection Switch
5. 8 Full-Time Battery Powered and Surge
Protected Outlets
6. AC Power Cord
7. Output Circuit Breaker
8. Input Circuit Breaker
9. USB Port
10. Communication Protection Ports RJ45
11. Wiring Fault Indicator (Red)
12. Coax.Cable.DSS Surge Protection
13. Serial Port I (Primary)
14. Serial Port II (Dry Contact)
15. EPO (Emergency Power O) Port
16. SNMP / HTTP Network Slot
17. External Battery Pack Connector
FPO

Thank you for purchasing a CyberPower product. This UPS is designed to provide unsurpassed
power protection, operation, and performance during the lifetime of the product. Please take a
few minutes to register your product at: www.CyberPowerSystems.com/registration.
Registration certifies your product’s warranty, confirms your ownership in the event of a
product loss or theft, and entitles you to free technical support. Register your product now to
receive the benefits of CyberPower ownership.
CAUTION! To prevent the risk of fire or
electric shock, install in a temperature and
humidity controlled indoor area free of
conductive contaminants. (Please see
specifications for acceptable temperature
and humidity range).
CAUTION! To reduce the risk of electric shock,
do not remove the cover except to service the
battery. Turn o and unplug the unit before
servicing the batteries. There are no user
serviceable parts inside except for the battery.
CAUTION! Hazardous live parts inside can be
energized by the battery even when the AC
input power is disconnected.
CAUTION! The UPS must be connected to an
AC power outlet with fuse or circuit breaker
protection. Do not plug into an outlet that is
not grounded. If you need to de-energize this
equipment, turn o and unplug the unit.
CAUTION! To avoid electric shock, turn o the
unit and unplug it from the AC power source
before installing a computer component.
CAUTION! To reduce the risk of fire, connect
only to a circuit provided with 20 amperes
maximum branch circuit over current
protection in accordance with the National
Electric Code, ANSI/NFPA 70.
CAUTION! Not for use in a computer room
as defined in the Standard for the Protection
of Electronic Computer/Data Processing
Equipment, ANSI/NFPA 75.
CAUTION! Do not dispose of batteries in a
fire. The batteries may explode.
CAUTION! Do not open or mutilate batteries.
Released electrolyte is harmful to the skin and
eyes. It may be toxic.
DO NOT USE FOR MEDICAL
OR LIFE SUPPORT EQUIPMENT!
CyberPower Systems does not sell products
for life support or medical applications. DO
NOT use in any circumstance that would
aect operation and safety of life support
equipment, any medical applications or
patient care.
DO NOT USE WITH OR NEAR AQUARIUMS!
To reduce the risk of fire or electric shock,
do not use with or near an aquarium.
Condensation from the aquarium can cause
the unit to short out.
DO NOT USE THE UPS
ON ANY TRANSPORTATION!
To reduce the risk of fire or electric shock, do
not use the unit on any transportation such
as airplanes or ships. The eect of shock or
vibration caused during transit and the damp
environment can cause the unit to short out.
PRODUCT REGISTRATION
IMPORTANT SAFETY WARNINGS (SAVE THESE INSTRUCTIONS)
This manual contains important safety instructions. Please read and follow all instructions carefully
during installation and operation of the unit. Read this manual thoroughly before attempting to
unpack, install, or operate your UPS.

INSTALLING YOUR UPS SYSTEM
UNPACKING
Inspect the UPS upon receipt.
The box should contain the following:
(a) UPS unit
(b) User’s manual
(c) Rack mount brackets x 2
(d) Stands x 2
(e) Telephone cable
(f) Emergency power o cable (gray)
(g) Serial cable x 2
(h) USB A+B type cable
PowerPanel® Business Edition software is
available on our website. Please visit www.
cyberpowersystems.com and go to the
Software Section for a free download.
OVERVIEW
The OR1500LCDRTXL2U/OR2200LCDRTXL2U
provides complete power protection from
utility power that is not always consistent. The
OR1500LCDRTXL2U features 1840 Joules of
surge protection and the OR2200LCDRTXL2U
features 2060 Joules of surge protection.
Both units provide long lasting battery backup
during power outages with maintenance
free batteries. The OR1500LCDRTXL2U/
OR2200LCDRTXL2U ensure consistent power
to your computer system and include software
that will automatically save your open files
and shutdown your computer system during a
utility power loss.
AUTOMATIC VOLTAGE REGULATOR
The OR1500LCDRTXL2U/OR2200LCDRTXL2U
stabilizes inconsistent utility power voltage
to nominal levels that are safe for equipment.
Inconsistent incoming utility power may be
damaging to important data files and hardware,
but with Automatic Voltage Regulation (AVR),
damaging voltage levels are corrected to safe
levels. AVR automatically increases low utility
power and decreases high
utility power to a consistent
and safe 110/120 volts. If
incoming utility voltage
drops below 90 volts, or
exceeds 140 volts the units
automatically switch to
battery back-up power.
DETERMINE THE POWER
REQUIREMENTS OF YOUR EQUIPMENT
1. Ensure that the equipment plugged
into the outlet does not exceed the UPS
unit’s rated capacity (1500VA/1125W for
OR1500LCDRTXL2U, 2190VA/1650W
for OR2200LCDRTXL2U). If the rated
capacities of the unit are exceeded, an
overload condition may occur and cause
the UPS unit to shut down or the circuit
breaker to trip.
2. There are many factors that can aect
the amount of power that your computer
system will require. It is suggested that
the load placed on the battery outlets not
exceed 80% of the unit’s capacity.
HARDWARE INSTALLATION GUIDE
1. Your new UPS may
be used immediately
upon receipt. However,
recharging the battery
for at least 8 hours is
highly recommended to
ensure that the battery’s
maximum charge
capacity is achieved.
A loss of charge may
occur during shipping
and storage. To
recharge the battery,
simply leave the unit
plugged into an AC
outlet.
2. With the UPS unit
turned o and unplugged, connect
your computer, monitor, and any other
peripherals requiring battery backup into
the battery power supplied outlets. Plug
the other peripheral equipments (printer,
scanner, speakers) into the full-time surge
protection outlets. DO NOT plug a laser
printer, paper shredder, copier, space
heater, vacuum, sump pump or other large
electrical devices into the UPS. The power
demands of these devices will overload and
possibly damage the unit.
-continued

INSTALLING YOUR UPS SYSTEM - continued
3. To protect a fax, phone or modem, connect
a telephone cable or network cable from
the wall jack outlet to the IN jack of the
UPS. Connect a telephone cable
or network cable from the
OUT jack of the UPS to a fax
machine, telephone, modem, or
network devices.
4. Plug the UPS into a 2-pole,
3-wire grounded receptacle (wall outlet).
Make sure the wall branch outlet is
protected by a fuse or circuit breaker and
does not service equipment with large
electrical demands (e.g. air conditioner,
refrigerator, copier, etc.). The warranty
prohibits the use of extension cords, outlet
strips, and surge strips.
5. Press the power switch to turn the unit on.
The Power On indicator light will illuminate
and the unit will “beep”. If an overload is
detected, an audible alarm will sound and
the unit will emit one long beep. To correct
this, turn the UPS o and unplug at least
one piece of equipment from the battery
power supplied outlets. Make sure the
circuit breaker is depressed and then turn
the UPS on.
6. To maintain optimal battery charge,
leave the UPS plugged into an AC outlet
at all times.
7. To store the UPS for an extended period,
cover it and store with the battery fully
charged. While in storage, recharge the
battery every three months to ensure
battery life.
8. To use PowerPanel® Business Edition
software, connect the serial cable to the
serial port or the USB port on the UPS
and the computer. These OR units include
one serial port, one dry contact, and
one USB port to allow connection and
communication between the UPS and
computers. Serial port II produces basic
information for equipment that can utilize
a dry contact UPS. The primary computer
(with PowerPanel® Business Edition
installed) is the computer that you will use
to control the UPS and make changes to
the operation of the UPS. When there is
a power failure, the computer connected
to the Primary port will start to shut down
after a user controlled delay. PowerPanel®
Business Edition will save and close any
open files prior to shutting down the
system.
FPO

BASIC OPERATION
1. Power Switch
Master on/o switch for equipment
connected to the UPS.
2. Power On Indicator (blue)
This LED is illuminated when the utility
power is normal and the UPS outlets are
providing power, free of surges and spikes.
3. LCD module display
Crystal Blue intelligent LCD panel shows
all the UPS information using icons and
messages. For more information please
review the “Definitions for Illuminated LCD
Indicators” section below.
4. LCD function selection switch
The switch can be used to select the LCD
display contents including input/output
voltage and estimated run time, etc.
5. 8 Full Time Battery Powered and Surge
Protected Outlets
The unit has eight battery powered/
surge suppression outlets for connected
equipments to ensure temporary
uninterrupted operation of your equipment
during a power failure. (DO NOT plug a
laser printer, paper shredder, copier, space
heater, vacuum, sump pump or other large
electrical devices into the UPS. The power
demands of these devices will overload
and possibly damage the unit.)
6. AC Input Power Cord
Heavy-duty, extra long power cord.
7. Output Circuit Breaker
Resettable circuit breakers provide output
optimal overload protection.
8. Input Circuit Breaker
Resettable circuit breakers provide input
optimal overload protection.
9. USB Port
The USB port allows connection and
communication between the USB port on
the computer and the UPS unit.
10.Communication Protection Ports
Communication protection ports will
protect any standard modem, fax,
telephone line, network or Ethernet
connection (RJ11/RJ45).
11. Wiring Fault Indicator (red)
This LED indicator will illuminate to warn
the user that a wiring problem exists, such
as bad ground, missing ground or reversed
wiring. If this is illuminated, disconnect
all electrical equipments from the outlet
and have an electrician verify the outlet is
properly wired. The unit will not provide
surge protection without being plugged
into a grounded and properly wired wall
outlet.
12. Coax/Cable/DSS Surge Protection
The Coax/Cable/DSS surge protection
ports will protect any cable modem, CATV
converter, or DSS receiver.
13. Serial Port I (Primary)
The serial port allows connection and
communication between the UPS and the
computer.
14.Serial Port II (Dry Contact)
Dry contact produces information for
equipment that can utilize dry contact
signals.
15. EPO (Emergency Power O) Port:
Use the provided gray cable to connect to
a special EPO contact switch. Follow the
appropriate circuit diagram below to wire
the cable to your EPO configuration. The
EPO remote switch is a switch installed
in an outside area, connected to the unit
via the Emergency Power O cable. In
case of an emergency, it can be used to
immediately cut-o power from the UPS.
16. SNMP/HTTP Network Slot:
Remove the cover panel to install an
optional RMCARD provides remote
monitoring and management of your UPS
over a network.
17. External Battery Pack Connector
Use to connect the optional CyberPower
external battery packs for extended
runtime.

Read and follow the IMPORTANT SAFETY
INSTRUCTIONS before servicing the battery.
Service the battery under the supervision of
personnel knowledgeable of batteries and
their precautions. CAUTION! Servicing of the
battery should only be performed by trained
personnel familiar with batteries and their
precautions. For more information on battery
replacement, contact your dealer or call the
number on this manual.
Replacement of batteries located in an
OPERATOR ACCESS AREA.
1. When replacing batteries, replace with
the same number of the following
battery: CyberPower RBP834 for the
OR1500LCDRTXL2U; CyberPower RBP844
for the OR2200LCDRTXL2U.
2. CAUTION! Risk of Energy Hazard, 12 V,
maximum 7(for the OR1500LCDRTXL2U) or
9 (for the OR2200LCDRTXL2U) Ampere-
hour battery. Before replacing batteries,
remove conductive jewelry such as chains,
wrist watches, and rings. High energy
conducted through these materials could
cause severe burns;
3. CAUTION! Do not dispose of batteries in a
fire. The batteries may explode;
4. CAUTION! Do not open or mutilate
batteries. Released material is harmful to
the skin and eyes. It may be toxic.
CAUTION - RISK OF EXPLOSION IF BATTERY
IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING
TO LOCAL REGULATIONS
REPLACING THE BATTERY
BATTERY REPLACEMENT PROCEDURE:
1. Remove the right side front panel.
2. Remove the three retaining screws of the cable protection cover then remove the cover.
3. Remove the two retaining screws of the cable connectors.
4. Disconnect the black and red cable
5. Remove the four retaining screws.
6. Insert the new battery pack. Assemble the screws, cover, cable and front panel in the reverse
sequence of above steps. Recharge the unit for 4-8 hours to ensure the UPS performs
expected runtime.
REMINDER: Batteries are considered HAZARDOUS WASTE and must be disposed of properly. Most retailers that sell lead-acid
batteries collect used batteries for recycling, as required by local regulations.
123
4
56

DEFINITIONS FOR ILLUMINATED LCD INDICATORS
1. INPUT Voltage Meter: This meter measures
the AC voltage that the UPS system is re-
ceiving from the utility wall outlet. The UPS
is designed, through the use of automatic
voltage regulation, to continuously correct
output voltage to connected equipment
to a safe 110/120 voltage output range. In
the event of a complete power loss, severe
brownout, or over-voltage, the UPS relies
on its internal battery to supply consistent
110/120 output voltage. The INPUT voltage
meter can be used as a diagnostic tool to
identify poor-quality input power.
2. OUTPUT Voltage Meter: This meter mea-
sures, in real time, the AC voltage that the
UPS system is providing to the computer,
such as normal line mode, AVR mode, and
battery backup mode. (Note: The OUTPUT
voltage meter shows the status of the bat-
tery backup outlets.)
3. ESTIMATED Run Time: This displays the
run time estimate of the UPS with current
battery capacity and load.
4. NORMAL Icon: This icon appears when the
UPS is working under normal conditions.
5. BATTERY Icon: During a severe brown-
out or blackout, this icon appears and an
alarm sounds (two short beeps followed
by a pause) to indicate the UPS is oper-
ating from its internal batteries. During a
prolonged brownout or blackout, the alarm
will beep rapidly every 1/2 second (and
the BATT.CAPACITY meter shows one 20%
capacity segment shaded) to indicate the
UPS’s batteries are nearly out of power. You
should save files and turn o your equip-
ment immediately.
6. AVR (Automatic Voltage Regulation) Icon:
This icon appears whenever your UPS
is automatically correcting low AC line
voltage without using battery power. This is
a normal, automatic operation of your UPS,
and no action is required on your part.
7. SILENT MODE Icon: This icon appears
whenever the UPS is in silent mode. The
buzzer does not beep during silent mode
until the battery reaches low capacity.
8. OVER LOAD Icon: This icon appears and an
alarm sounds to indicate the battery-sup-
plied outlets are overloaded. To clear the
-continued
The LCD screen indicates a variety of UPS
operational conditions. All descriptions
apply when the UPS is plugged into an AC
outlet and turned on or when the UPS is
on battery.
NORMAL BATTERY
OVER
LOAD ALARM
CONDITION
On O O O Normal
O On O
Beep twice
every 30
seconds
Utility Failure - The UPS is providing power to
battery power-supplied outlets from its battery.
O On O
Rapid
beeping
every 1/2
second
Utility Failure - The UPS is providing battery power.
Rapid beeping indicates the unit will run out of
power soon
O On On Constant
tone
Battery Overload - Occurs when connected equip-
ment exceeds the listed capacity of the UPS. Turn
the UPS o, unplug at least one piece of equipment
from battery outlets, wait 10 seconds, reset the circuit
breaker and turn the unit on.

Additional troubleshooting information can be found at “Support” at www.CyberPowerSystems.com
TROUBLESHOOTING
Problem Possible Cause Solution
Full-time surge protection
outlets stop providing power
to equipment.
Circuit breaker has been tripped
due to an overload.
Turn the UPS o and unplug at
least one piece of equipment.
Wait 10 seconds, reset the circuit
breaker by depressing the button,
and then turn the UPS on.
The UPS does not perform
expected runtime.
Battery not fully charged. Recharge the battery by leaving
the UPS plugged in.
Battery is worn out.
Contact CyberPower Systems
about replacement batteries at:
cyberpowersystems.com/support.
The UPS will not turn on.
The on/o switch is designed
to prevent damage from rapidly
turning it o and on.
Turn the UPS o. Wait 10 seconds
and then turn the UPS on.
The unit is not connected to an
AC outlet.
The unit must be connected to a
110/120V 60Hz outlet.
The battery is worn out.
Contact CyberPower Systems
about replacement batteries at:
cyberpowersystems.com/support.
Mechanical problem. Contact CyberPower Systems at:
cyberpowersystems.com/support.
PowerPanel® Business Edition is
inactive (all icons are gray).
The USB/Serial cable is not
connected.
Connect the USB/serial cable to
the UPS unit and an open USB/
serial port on the back of the com-
puter. You must use the cable that
came with the unit.
The USB/serial cable is connected
to the wrong port.
Check the back of the computer
for an additional USB/serial port.
Move the cable to this port.
The unit is not providing
battery power.
Shutdown your computer and turn
the UPS o. Wait 10 seconds and
turn the UPS back on. This should
reset the unit.
The serial cable is not the cable
that came with the unit.
Please use the serial cable that
came with the unit for the
software.
DEFINITIONS FOR ILLUMINATED LCD INDICATORS - continued
overload, unplug some of your equipment
from the battery-supplied outlets until the
icon turns o and the alarm stops.
9. FAULT icon: This icon appears if there is a
problem with the UPS, Contact CyberPow-
er Systems at tech@cyberpowersystems.
com for further help and support.
10.BATT. CAPACITY meter: This meter dis-
plays the approximate charge level (in 20%
increments) of the UPS’s internal battery.
During a blackout or severe brownout, the
UPS switches to battery power, the BAT-
TERY icon appears, and the charge level
decreases.
11. LOAD CAPACITY meter: This meter dis-
plays the approximate output load level
(in 20% increments) of the UPS battery
outlets.

TECHNICAL SPECIFICATIONS
Model OR1500LCDRTXL2U OR2200LCDRTXL2U
Capacity 1500VA / 1125W 2190VA / 1650W
Input Voltage or Utility 90V to 140V
Input Frequency 47 Hz ± 63 Hz (Auto-sensing)
On-Battery Output Voltage 120Vac ± 5%
Transfer Time 4 ms Typical
Max Load for UPS Outlets
(8 Outlets) 1500VA / 1125W 2190VA / 1650W
On-Battery Output
Wave Form Simulated Sine Wave Form
Operating Temperature + 32°F to 104° F / 0° C to 40° C
Operating Relative Humidity 0 to 90% non-condensing
Size (L x W x H) 433 x 478 x 88 mm (2U Rack) / 17 x 18.8 x 3.5 in.
Net Weight 59.5 lbs. / 27 kg 66.1 lbs. / 30 kg
Battery Type CyberPower / RBP834 CyberPower / RBP844
Typical Battery
Recharge Time 8 hours
Typical Battery Life 3 to 6 years, depending on number of discharge/recharge cycles
Recommended Battery Sealed Maintenance Free Lead Acid Battery
Safety Approvals UL1778, CSA C22.2 No 107.3, FCC/DoC Class B
SYSTEM FUNCTION BLOCK DIAGRAM
Input Output
Battery Mode
Normal Mode
EMI
Filter
Surge
Suppressor
Inverter
Charger
AC / DC
Battery
AVR

Advanced Energy-Saving Patented Bypass Technology
CyberPower’s patented GreenPower UPS™ with Bypass Technology reduces UPS energy
costs by up to 75% compared to conventional UPS models. Even when utility power
is normal, conventional UPS models constantly pass power through a transformer.
By contrast, under normal conditions the advanced circuitry of a GreenPower UPS™
bypasses the transformer. As a result, the power eciency is significantly increased
while decreasing waste heat, using less energy, and reducing energy costs. When an
abnormal power condition occurs, the GreenPower UPS™ automatically runs power
through its transformer to regulate voltage and provide “safe” power. Since utility power is normal over 88% of
the time, the GreenPower UPS™ operates primarily in its ecient bypass mode. The GreenPower UPS™ is also
manufactured in accordance with the Restriction on Hazardous Substances (RoHS) directive making it one
of the most environmentally-friendly on the market today.
CYBERPOWER GREENPOWER UPS™ TECHNOLOGY
GREEN POWER UPS™
Energy-Saving Technology
Please visit www.CyberPowerSystems.com for a copy of the Limited Warranty and Connected
Equipment Guarantee.
Where Can I Get More Information?
The application of the United Nations Convention of Contracts for the International Sale of
Goods is expressly excluded. CyberPower is the warrantor under this Limited Warranty.
For further information please feel free to contact CyberPower at:
Cyber Power Systems (USA), Inc. 4241 12th Ave E., STE 400, Shakopee, MN 55379;
call us at [phone]; or submit a web ticket online at cyberpowersystems.com/support.
Cyber Power Systems (USA), Inc. encourages environmentally sound methods for disposal
and recycling of its UPS products. Please dispose and/or recycle your UPS and batteries in
accordance to the local regulations of your state.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit dierent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Canadian Compliance Statement
CAN ICES-3 (B)/NMB-3(B)
LIMITED WARRANTY AND CONNECTED EQUIPMENT GUARANTEE
FCC COMPLIANCE STATEMENT
© 2022 CyberPower Systems (USA), Inc. PowerPanel® Personal is a trademark of Cyber Power Systems(USA) Inc.
All rights reserved. All other trademarks are the property of their respective owners.
WARNING: This product can expose you to chemicals including bisphenol A (BPA) and styrene, which is known to the
State of California to cause reproductive harm and cancer. For more information, go to www.P65Warnings.ca.gov.