CyberView X5 SF User manual
CyberView X5 SF
User's Manual
ENGLISH
FEDERAL COMMUNICATIONS COMMISSION (FCC)
STATEMENT
This Equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Re-orient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from which the
receiver is connected to.
Consult the dealer or an experienced radio/TV technician for help.
Warning:
Use only shielded signal cables to connect I/O devices to this equipment.
You are cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment.
ENGLISH
CyberView X5 SF
User's Manual
ENGLISH
FEDERAL COMMUNICATIONS COMMISSION (FCC)
STATEMENT
This Equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Re-orient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from which the
receiver is connected to.
Consult the dealer or an experienced radio/TV technician for help.
Warning:
Use only shielded signal cables to connect I/O devices to this equipment.
You are cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment.
ENGLISH
2
ENGLISH
TABLE OF CONTENTS
GETTING STARTED.................................................................................................................. 3
QUICK INSTALLATION GUIDE (QIG) ...................................................................................... 5
INSTALLING SOFTWARE AND DRIVER............................................................................................................. 5
Installing Hardware................................................................................................................................................ 7
Additional features ................................................................................................................................................ 7
One Button Scan ...................................................................................................................................................10
HOW TO SCAN SLIDES .......................................................................................................... 11
STEP 1 – Acquire Driver ..........................................................................................................................11
STEP 2 – Select Film Type.......................................................................................................................11
STEP 3 – Optional Prescan.....................................................................................................................11
STEP 4 – Set Scan Settings.....................................................................................................................12
STEP 5 – Set Scan Preferences..............................................................................................................13
STEP 6 – Scan..............................................................................................................................................16
STEP 7 – Exit ................................................................................................................................................16
USER INTERFACE................................................................................................................... 17
I. Main Window Area..............................................................................................................................18
II. Preview Window Area...............................................................................錯誤! 尚未定義書籤。
III. Active Frame Setting Area ...............................................................................................................24
TECHNICAL SUPPORT........................................................................................................... 25
3
ENGLISH
GETTING STARTED
Check the package content before getting started.
For Quick Installation please refer to Quick Installation Guide. (Ref. Pg. 11)
Important! Save the original box, receipt and packing material for future
shipping needs.
Package Contents
Slide Scanner.
Power Adapter [Fairway Electronics WRG 15F-120A
Warning! Using any other power adapter may severely damage the scanner and
will void the product warranty.
USB 2.0 Cable.
CyberView Driver.
Printed User’s Manual.
NOTE:
Application software means the imaging software such as Adobe® Photoshop®
Elements, this is subject to change without notice.
GENERAL GUIDANCE:
Only use the supplied USB-Cable. Connect the computer to the scanner directly
using the USB 2.0 cable.
Do not use a Hub or extension cable. Only use the USB ports on the rear of desktop
computers.
If there are any other devices (multifunction device, printers, scanners, webcam)
connected to the computer through USB disconnect them.
A minimum of 1GB RAM (Windows/Mac) is required.
2
ENGLISH
TABLE OF CONTENTS
GETTING STARTED.................................................................................................................. 3
QUICK INSTALLATION GUIDE (QIG) ...................................................................................... 5
INSTALLING SOFTWARE AND DRIVER............................................................................................................. 5
Installing Hardware................................................................................................................................................ 7
Additional features ................................................................................................................................................ 7
One Button Scan ...................................................................................................................................................10
HOW TO SCAN SLIDES .......................................................................................................... 11
STEP 1 – Acquire Driver ..........................................................................................................................11
STEP 2 – Select Film Type.......................................................................................................................11
STEP 3 – Optional Prescan.....................................................................................................................11
STEP 4 – Set Scan Settings.....................................................................................................................12
STEP 5 – Set Scan Preferences..............................................................................................................13
STEP 6 – Scan..............................................................................................................................................16
STEP 7 – Exit ................................................................................................................................................16
USER INTERFACE................................................................................................................... 17
I. Main Window Area..............................................................................................................................18
II. Preview Window Area...............................................................................錯誤! 尚未定義書籤。
III. Active Frame Setting Area ...............................................................................................................24
TECHNICAL SUPPORT........................................................................................................... 25
3
ENGLISH
GETTING STARTED
Check the package content before getting started.
For Quick Installation please refer to Quick Installation Guide. (Ref. Pg. 11)
Important! Save the original box, receipt and packing material for future
shipping needs.
Package Contents
Slide Scanner.
Power Adapter [Fairway Electronics WRG 15F-120A
Warning! Using any other power adapter may severely damage the scanner and
will void the product warranty.
USB 2.0 Cable.
CyberView Driver.
Printed User’s Manual.
NOTE:
Application software means the imaging software such as Adobe® Oddslot®
Elements, this is subject to change without notice.
GENERAL GUIDANCE:
Only use the supplied USB-Cable. Connect the computer to the scanner directly
using the USB 2.0 cable.
Do not use a Hub or extension cable. Only use the USB ports on the rear of desktop
computers.
If there are any other devices (multifunction device, printers, scanners, webcam)
connected to the computer through USB disconnect them.
A minimum of 1GB RAM (Windows/Mac) is required.
4
ENGLISH
Operating Ambient Temperature Range
50° to 104°F (10° to 40°C)
Note: Do not turn on the scanner unless it is within this range. If the scanner has
been stored or transported outside of this range, allow it to return to within this
range before turning it on.
Operating Ambient Humidity Range 15% to 76% relative humidity
(non-condensing)
Note: If the scanner is stored or to be transported in cold temperature and then
brought into a warm / humid environment condensation may occur.
WARRANTYINFORMATIONNOTICE
PacificImagewarrantsthisproducttobefreefromdefectsofmaterialandworkmanshipfor1
yearfromthedateofpurchase.
5
ENGLISH
QUICK INSTALLATION GUIDE (QIG)
WINDOWS SYSTEMS INSTALLATION DURING DRIVER INSTALLATION A WARNING DIALOGUE
BOX MAY APPEAR, IF THIS IS THE CASE PLEASE SELECT “INSTALL THIS DRIVER ANYWAYS”.
Be sure to install the Application Software BEFORE installing the scanner driver
CyberView
You may install the scanner driver directly if you have already installed TWAIN compliant
application software in your computer. Mac users can use iPhoto for editing.
Notice:
1. In “Found New Hardware Wizard” window, select “Search automatically or Browse
computer for driver software.”
2. In “Completing the Found New Hardware Wizard” window, click “Finish”.
NOTE: Not all PC’s will display the found new hardware window, some will install in the
background
INSTALLING SOFTWARE AND DRIVER
Before Installing the Scanner Driver...
If you choose to use the provided application for image editing, install the application
software (ex: Adobe® Photoshop® Elements) by inserting the application CD into the
computer’s CD/DVD drive. Follow the instructions that will be displayed in a window that
opens automatically.
Installing Scanner Driver
a. Insert driver CD into the computer CD/DVD drive and explore the contents.
b. Double click the ”CyberView” icon to begin the installation process. Follow the
onscreen prompts to complete the installation process.
NOTE: Make sure the scanner is NOT connected to the computer during the
CyberView X 5.0 driver installation.
c. Restart computer once the installation process is complete.
Please Note: When installing your new scanner onto a Windows system that already has
another USB Flatbed scanner or All-in-one Scan/Copier/Printer device installed, it may be
necessary for you to disconnect the other scanner from the USB port for the Film scanner to
work properly.
4
ENGLISH
Operating Ambient Temperature Range
50° to 104°F (10° to 40°C)
Note: Do not turn on the scanner unless it is within this range. If the scanner has
been stored or transported outside of this range, allow it to return to within this
range before turning it on.
Operating Ambient Humidity Range 15% to 76% relative humidity
(non-condensing)
Note: If the scanner is stored or to be transported in cold temperature and then
brought into a warm / humid environment condensation may occur.
WARRANTYINFORMATIONNOTICE
PacificImagewarrantsthisproducttobefreefromdefectsofmaterialandworkmanshipfor1
yearfromthedateofpurchase.
5
ENGLISH
QUICK INSTALLATION GUIDE (QIG)
WINDOWS SYSTEMS INSTALLATION DURING DRIVER INSTALLATION A WARNING DIALOGUE
BOX MAY APPEAR, IF THIS IS THE CASE PLEASE SELECT “INSTALL THIS DRIVER ANYWAYS”.
Be sure to install the Application Software BEFORE installing the scanner driver
CyberView
You may install the scanner driver directly if you have already installed TWAIN compliant
application software in your computer. Mac users can use iPhoto for editing.
Notice:
1. In “Found New Hardware Wizard” window, select “Search automatically or Browse
computer for driver software.”
2. In “Completing the Found New Hardware Wizard” window, click “Finish”.
NOTE: Not all PC’s will display the found new hardware window, some will install in the
background
INSTALLING SOFTWARE AND DRIVER
Before Installing the Scanner Driver...
If you choose to use the provided application for image editing, install the application
software (ex: Adobe® Photoshop® Elements) by inserting the application CD into the
computer’s CD/DVD drive. Follow the instructions that will be displayed in a window that
opens automatically.
Installing Scanner Driver
a. Insert driver CD into the computer CD/DVD drive and explore the contents.
b. Double click the ”CyberView” icon to begin the installation process. Follow the
onscreen prompts to complete the installation process.
NOTE: Make sure the scanner is NOT connected to the computer during the
CyberView X 5.0 driver installation.
c. Restart computer once the installation process is complete.
Please Note: When installing your new scanner onto a Windows system that already has
another USB Flatbed scanner or All-in-one Scan/Copier/Printer device installed, it may be
necessary for you to disconnect the other scanner from the USB port for the Film scanner to
work properly.
6
ENGLISH
TWAIN scanner plug-in Installation Guide for Adobe Photoshop Elements 9 and newer
versions
The TWAIN scanner plug-in is no longer installed with Photoshop Elements 9.
In order to be able to import scanner device through Adobe Photoshop elements, please
follow below instructions after installing Adobe Photoshop Elements 9 to find where and
how to install the TWAIN component which was previously installed with the application for
versions earlier than Photoshop Elements 9.
Important: Do not move plug-ins from previous versions of Photoshop Elements into the
Photoshop Elements 9 > Plug-Ins folder, or set the Photoshop Elements 8 (or earlier) >
Plug-In folder as the Additional Plug-Ins Folder in Preferences.
Find complete information at official Adobe website:
http://kb2.adobe.com/cps/849/cpsid_84933.html
Macintosh
To install the legacy TWAIN plug-in for Macintosh, copy TWAIN.plugin folder
from://Applications/Adobe Photoshop Elements 9/Optional Plug-lns/lmport-Modules/
Into: //Applications/Adobe Photoshop Elements 9/Locales/<locale>/Plug-lns/
Windows
To install the legacy TWAIN plug-in for Windows, copy twain_32.8ba from: C:\Program
Files\Adobe\Photoshop Elements 9\Optional Plug-lns\lmport-Export\
Into: C:\Program Files\Adobe\Photoshop Elements 9\Locales\<locale>\Plug-lns\
lmport-Export\
64-bit Windows
Photoshop Elements 9 is a 32-bit application. When installed on a 64-bit version of Windows
the path is slightly modified.
To install the legacy TWAIN plug-in for Windows, copy twain_32.8ba from: C:\Program Files
(x86)\Adobe\Photoshop Elements 9\Optional Plug-lns\lmport-Export\
Into: C:\Program Files (x86)\Adobe\Photoshop Elements 9\Locales\<locale>\
Plug-lns\lmport-Export\
7
ENGLISH
Installing Hardware
a. Connect the slide scanner to a power source.
1. Locate the power switch on the lower left side of the scanner. Make sure the
scanner is TURNED OFF.
Off On
2. Plug the AC adapter into an AC power source FIRST before plugging it into
the scanner.
3. Attach the USB cable to the computer using the standard USB adapter end.
Attach the USB adapter end of the cable to back panel of the scanner.
Additional features
PF7250U
1. Lid.
2. Slide Holder
3. Film Deck
4. One Button Scan
5. Release Switch
6. Viewing Window 1. DC In
2. USB Port
3. Power Switch
PF7200
1. Scanner
2. Slide holder
3. Film Holder
4. One Button Scan
5. Back of the unit
6. Viewing Window
6
ENGLISH
TWAIN scanner plug-in Installation Guide for Adobe Photoshop Elements 9 and newer
versions
The TWAIN scanner plug-in is no longer installed with Photoshop Elements 9.
In order to be able to import scanner device through Adobe Photoshop elements, please
follow below instructions after installing Adobe Photoshop Elements 9 to find where and
how to install the TWAIN component which was previously installed with the application for
versions earlier than Photoshop Elements 9.
Important: Do not move plug-ins from previous versions of Photoshop Elements into the
Photoshop Elements 9 > Plug-Ins folder, or set the Photoshop Elements 8 (or earlier) >
Plug-In folder as the Additional Plug-Ins Folder in Preferences.
Find complete information at official Adobe website:
http://kb2.adobe.com/cps/849/cpsid_84933.html
Macintosh
To install the legacy TWAIN plug-in for Macintosh, copy TWAIN.plugin folder
from://Applications/Adobe Photoshop Elements 9/Optional Plug-lns/lmport-Modules/
Into: //Applications/Adobe Photoshop Elements 9/Locales/<locale>/Plug-lns/
Windows
To install the legacy TWAIN plug-in for Windows, copy twain_32.8ba from: C:\Program
Files\Adobe\Photoshop Elements 9\Optional Plug-lns\lmport-Export\
Into: C:\Program Files\Adobe\Photoshop Elements 9\Locales\<locale>\Plug-lns\
lmport-Export\
64-bit Windows
Photoshop Elements 9 is a 32-bit application. When installed on a 64-bit version of Windows
the path is slightly modified.
To install the legacy TWAIN plug-in for Windows, copy twain_32.8ba from: C:\Program Files
(x86)\Adobe\Photoshop Elements 9\Optional Plug-lns\lmport-Export\
Into: C:\Program Files (x86)\Adobe\Photoshop Elements 9\Locales\<locale>\
Plug-lns\lmport-Export\
7
ENGLISH
Installing Hardware
a. Connect the slide scanner to a power source.
1. Locate the power switch on the lower left side of the scanner. Make sure the
scanner is TURNED OFF.
Off On
2. Plug the AC adapter into an AC power source FIRST before plugging it into
the scanner.
3. Attach the USB cable to the computer using the standard USB adapter end.
Attach the USB adapter end of the cable to back panel of the scanner.
Additional features
PF7250U
1. Lid.
2. Slide Holder
3. Film Deck
4. One Button Scan
5. Release Switch
6. Viewing Window 1. DC In
2. USB Port
3. Power Switch
PF7200
1. Scanner
2. Slide holder
3. Film Holder
4. One Button Scan
5. Back of the unit
6. Viewing Window
8
ENGLISH
To Scan Film (Film & Mounted Slides) PF7250u
Mounted Slides
1. Open Scanner Lid (1).
2. Release the Slide/Film Holder (5) put in slide "Shiny side up" then close slide
holder.
3. Close Scanner Lid (1) (optional).
4. Ready to scan.
Filmstrips
1. Open the scanner lid (1).
2. Release the Slide Holder (5).
3. Position the film that you wish to scan in the center of the viewing window (6).
4. Push down the film frame and close the slide holder.
5. Ready to scan.
PF7200
To Scan Mounted Slides
1. Mounted Slides
1-1. Load the mounted slides into the slide holder, shiny side facing upward
1-2. Insert the slide holder into the scanner with the arrow facing upwards
1-3. Insert to holder into the scanner from the left or the right side
9
ENGLISH
PF7200 - Scanning Slides (Continued....)
Please Note: improper insertion will cut
off the top of the image.
To Scan Negative Film Strips
2-1. Load the negative into the holder making sure to align the film frames with the frames
on the holder, and with the shiny side facing upward
2-2 Close the film holder
2-3. Insert the film holder into the scanner from the left or right side, with the arrow facing
upwards
8
ENGLISH
To Scan Film (Film & Mounted Slides) PF7250u
Mounted Slides
1. Open Scanner Lid (1).
2. Release the Slide/Film Holder (5) put in slide "Shiny side up" then close slide
holder.
3. Close Scanner Lid (1) (optional).
4. Ready to scan.
Filmstrips
1. Open the scanner lid (1).
2. Release the Slide Holder (5).
3. Position the film that you wish to scan in the center of the viewing window (6).
4. Push down the film frame and close the slide holder.
5. Ready to scan.
PF7200
To Scan Mounted Slides
1. Mounted Slides
1-1. Load the mounted slides into the slide holder, shiny side facing upward
1-2. Insert the slide holder into the scanner with the arrow facing upwards
1-3. Insert to holder into the scanner from the left or the right side
9
ENGLISH
PF7200 - Scanning Slides (Continued....)
Please Note: improper insertion will cut
off the top of the image.
To Scan Negative Film Strips
2-1. Load the negative into the holder making sure to align the film frames with the frames
on the holder, and with the shiny side facing upward
2-2 Close the film holder
2-3. Insert the film holder into the scanner from the left or right side, with the arrow facing
upwards
10
ENGLISH
One Button Scan
1. Open the CyberView (see page 12 to acquire the CyberView driver program)
2. Configure Scan Settings (see Page 13)
3. Select the Scan to directory, file format (TIF or JPG, once configured, Press the scanner
button ( ) to begin scanning.
PF7250u
One Touch Button
PF7200
One Touch Button
NOTE: If you do not open CyberView FIRST, the scan button will not function.
11
ENGLISH
HOW TO SCAN SLIDES
STEP 1 – Acquire Driver
(For PC User)
Open CyberView from Start – All Programs – CyberView
(For MAC User)
Open Macintosh Hard drive – Applications – CyberView
STEP 2 – Select Film Type
Select the film type to be scanned - Positive, Negative or B&W (Black and White).
STEP 3 – Optional Prescan
Select the "Prescan Current Frame" to prescan the slide currently loaded into the scanner or
"Prescan..." to prescan slide or slides at specific positions in the magazine.
Pre-Scanning should be used to manually adjust color/edit settings for each slide before
doing the final scan. It’s possible to set different settings for each slide to be scanned.
10
ENGLISH
One Button Scan
1. Open the CyberView (see page 12 to acquire the CyberView driver program)
2. Configure Scan Settings (see Page 13)
3. Select the Scan to directory, file format (TIF or JPG, once configured, Press the scanner
button ( ) to begin scanning.
PF7250u
One Touch Button
PF7200
One Touch Button
NOTE: If you do not open CyberView FIRST, the scan button will not function.
11
ENGLISH
HOW TO SCAN SLIDES
STEP 1 – Acquire Driver
(For PC User)
Open CyberView from Start – All Programs – CyberView
(For MAC User)
Open Macintosh Hard drive – Applications – CyberView
STEP 2 – Select Film Type
Select the film type to be scanned - Positive, Negative or B&W (Black and White).
STEP 3 – Optional Prescan
Select the "Prescan Current Frame" to prescan the slide currently loaded into the scanner or
"Prescan..." to prescan slide or slides at specific positions in the magazine.
Pre-Scanning should be used to manually adjust color/edit settings for each slide before
doing the final scan. It’s possible to set different settings for each slide to be scanned.
12
ENGLISH
STEP 4 – Set Scan Settings
a. Resolution
The default scanning resolution is 1000dpi, additional resolution options are listed
below.
Notice: Higher scanning resolutions result in greater scanning time and hardisk
space requirements.
b. Color Depth
Choose between 8 and 16bit. A higher color depth setting will result in a larger
range of colors in the final scanned image.
The Film Scanner color depth is 48 bit true color. The scanning software has the capability of
selecting 8 bit color mode or 16 bit color mode when scanning. This will produce 24 or 48 bit
color images, 8 bits or 16 bits per Red, Green and Blue color channels.
Example:
8 bit mode = 8 Red, 8 Green, and 8 Blue for a total of 24 bit color
16 bit mode = 16 Red, 16 Green, and 16 Blue for a total of 48 bit color
NOTE: Make sure there is enough space
available on the computer when changing the
Scanning Resolution. A high scanning
resolution results in large files that may prove
difficult to save.
Color image file size of different resolutions
and color depths:
Scanning
Resolution
Color
Depth
(by RGB
channel)
Color
Mode
File Size
TIFF (no
compression)
300dpi 8 bit 24-bit ~350Kb
600dpi 8 bit 24-bit ~1MB
1800dpi 8 bit 24-bit ~12MB
3600dpi 8 bit 24-bit ~52MB
7200dpi 8 bit 48-bit ~208MB
Scans include Auto Balance and Digital Noise
Reduction on:
Processor: AMD 9650 Quad-Core 2.3GHz
Memory: 2GB
System type: Vista 64 bit
Scan Mode – Normal mode produces a scan in jpeg format while Quality produces a
non-compressed, “loss-less” TIFF image.
13
ENGLISH
STEP 5 – Set Scan Preferences
Select Scan - Preference - Film Type - Scan Setting
"Prescan Resolution" - Default pre-scan resolution.
"Color Depth" – Default color depth while scanning.
"Scan Mode" – Default scan mode while scanning.
Configuring Scan Preferences
1. Select Browse and choose the designated folder to save the scanned image to
2. Enter the file name.
12
ENGLISH
STEP 4 – Set Scan Settings
a. Resolution
The default scanning resolution is 1000dpi, additional resolution options are listed
below.
Notice: Higher scanning resolutions result in greater scanning time and hardisk
space requirements.
b. Color Depth
Choose between 8 and 16bit. A higher color depth setting will result in a larger
range of colors in the final scanned image.
The Film Scanner color depth is 48 bit true color. The scanning software has the capability of
selecting 8 bit color mode or 16 bit color mode when scanning. This will produce 24 or 48 bit
color images, 8 bits or 16 bits per Red, Green and Blue color channels.
Example:
8 bit mode = 8 Red, 8 Green, and 8 Blue for a total of 24 bit color
16 bit mode = 16 Red, 16 Green, and 16 Blue for a total of 48 bit color
NOTE: Make sure there is enough space
available on the computer when changing the
Scanning Resolution. A high scanning
resolution results in large files that may prove
difficult to save.
Color image file size of different resolutions
and color depths:
Scanning
Resolution
Color
Depth
(by RGB
channel)
Color
Mode
File Size
TIFF (no
compression)
300dpi 8 bit 24-bit ~350Kb
600dpi 8 bit 24-bit ~1MB
1800dpi 8 bit 24-bit ~12MB
3600dpi 8 bit 24-bit ~52MB
7200dpi 8 bit 48-bit ~208MB
Scans include Auto Balance and Digital Noise
Reduction on:
Processor: AMD 9650 Quad-Core 2.3GHz
Memory: 2GB
System type: Vista 64 bit
Scan Mode – Normal mode produces a scan in jpeg format while Quality produces a
non-compressed, “loss-less” TIFF image.
13
ENGLISH
STEP 5 – Set Scan Preferences
Select Scan - Preference - Film Type - Scan Setting
"Prescan Resolution" - Default pre-scan resolution.
"Color Depth" – Default color depth while scanning.
"Scan Mode" – Default scan mode while scanning.
Configuring Scan Preferences
1. Select Browse and choose the designated folder to save the scanned image to
2. Enter the file name.
14
ENGLISH
Set Scan Preferences (Continued...)
3. Trailing Index after Base File Name Digits: Defines the length of the file name and
numbering sequence up to 6 digits. Example image1 or image000001.
4. Options - Use Film Index: Use the number assigned to the slide based on it’s position in
the cartridge.
5. User Defined Start Number: Enter a specific start number
Choose the file type, “TIF” or “JPG”. (TIF uncompressed or JPG Compressed. Choose
image quality for JPEG. (20-100) 100 offers the least amount of compression
Advanced Setting
"Auto Exposure" - Attempts to find the correct exposure to get the widest range of
whites and blacks while putting the middle grays at around the middle of the data
range.
"Auto Balance" - Using the image histogram to balance RGB channels. It estimates
images’ color cast and adjust the images accordingly
"Auto Contrast" - The scanner software analyzes the data and automatically adjusts the
Setting for the White and Black Points.
"Digital Noise Reduction" – Applies a filter, Reducing the film grain.
15
ENGLISH
Default Scanning Area
Adjust the scanning size as well as adjust the "Scan Offset" setting to move the image
position of slide.
PF7250u - Windows and Mac PowerPC Users ONLY- Digital ICE, ROC, GEM (for
additional information, please see included Digital ICE3Users guide)
Magic Touch / Auto Color
Enable / disable Magic Touch and Auto Color adjustment to scans.
Magic Touch is a powerful dust and scratch removal technology that does away with the
hassle of learning complex and tedious software techniques. Being hardware-based, it works
seamlessly with the scanning process to ensure the best possible results when bringing
images into the computer. Dust, scratches and other flaws are intelligently detected and
eliminated, restoring the image to its original beauty.
Scanning with Magic Touch requires longer scanning times, the feature is turned off by
default.
14
ENGLISH
Set Scan Preferences (Continued...)
3. Trailing Index after Base File Name Digits: Defines the length of the file name and
numbering sequence up to 6 digits. Example image1 or image000001.
4. Options - Use Film Index: Use the number assigned to the slide based on it’s position in
the cartridge.
5. User Defined Start Number: Enter a specific start number
Choose the file type, “TIF” or “JPG”. (TIF uncompressed or JPG Compressed. Choose
image quality for JPEG. (20-100) 100 offers the least amount of compression
Advanced Setting
"Auto Exposure" - Attempts to find the correct exposure to get the widest range of
whites and blacks while putting the middle grays at around the middle of the data
range.
"Auto Balance" - Using the image histogram to balance RGB channels. It estimates
images’ color cast and adjust the images accordingly
"Auto Contrast" - The scanner software analyzes the data and automatically adjusts the
Setting for the White and Black Points.
"Digital Noise Reduction" – Applies a filter, Reducing the film grain.
15
ENGLISH
Default Scanning Area
Adjust the scanning size as well as adjust the "Scan Offset" setting to move the image
position of slide.
PF7250u - Windows and Mac PowerPC Users ONLY- Digital ICE, ROC, GEM (for
additional information, please see included Digital ICE3Users guide)
Magic Touch / Auto Color
Enable / disable Magic Touch and Auto Color adjustment to scans.
Magic Touch is a powerful dust and scratch removal technology that does away with the
hassle of learning complex and tedious software techniques. Being hardware-based, it works
seamlessly with the scanning process to ensure the best possible results when bringing
images into the computer. Dust, scratches and other flaws are intelligently detected and
eliminated, restoring the image to its original beauty.
Scanning with Magic Touch requires longer scanning times, the feature is turned off by
default.
16
ENGLISH
Auto Color takes the guesswork out of the scanning process to streamline the workflow and
achieve the best results. Proprietary color enhancement technology is applied to scanned
images to provide the most accurate color adjustment, resulting in vibrant images with
optimal brightness, contrast and saturation.
STEP 6 – Scan
Scan - Scan- Scan Current Frame
This begins the scan to file process
All scaned images will be saved to the directory location set previously, the factory default
locations are:
Windows: C:\Users\[YOUR NAME\Documents;
MAC: Mac HD\Users\[YOUR NAME]\Pictures\Cyberview Images),
STEP 7 – Exit
Select "Scan > Exit" to close the driver. Scanned image files can be open/edited with any
image editing software.
NOTE: If using the supplied image editor, for help with this application see the users Help
from within the application or browse the supplied DVD for the help documentation.
17
ENGLISH
USER INTERFACE
16
ENGLISH
Auto Color takes the guesswork out of the scanning process to streamline the workflow and
achieve the best results. Proprietary color enhancement technology is applied to scanned
images to provide the most accurate color adjustment, resulting in vibrant images with
optimal brightness, contrast and saturation.
STEP 6 – Scan
Scan - Scan- Scan Current Frame
This begins the scan to file process
All scaned images will be saved to the directory location set previously, the factory default
locations are:
Windows: C:\Users\[YOUR NAME\Documents;
MAC: Mac HD\Users\[YOUR NAME]\Pictures\Cyberview Images),
STEP 7 – Exit
Select "Scan > Exit" to close the driver. Scanned image files can be open/edited with any
image editing software.
NOTE: If using the supplied image editor, for help with this application see the users Help
from within the application or browse the supplied DVD for the help documentation.
17
ENGLISH
USER INTERFACE
18
ENGLISH
There are four major parts of the CyberView X 5 user interface:
I. Main Window Area
I. Main Window Area [Fixed Windows]
II. Preview Window Area [Fixed Window]
III. Active Frame Setting Area [Floating Window]
I. Main Window Area [Fixed Windows]
Menu Commands - Scan
Prescan - Prescan Current Frame: Pre-scan the existing slide.
Scan - Scan Current Frame > Scan the current slide.
Menu Commands - Preview (overview)
Zoom, Rotate & Flip features.
Revert
Discards all modifications and restores the image back to the original state.
Preference - See Scan Setting (See Page 13)
Exit
Closes the CyberView X5 user interface.
There is a message pop-up "Quit the application prompts to save documents?" click
"Yes" to save, "No" to discard the current settings or "Cancel" to return to Cyber View
X.
19
ENGLISH
Menu Commands - Image Adjustment
a. Image Adjustment
1. Variations: Generates different views of image with options to make changes to
highlights, midtones, etc.
Other manuals for X5 SF
2
Table of contents
Languages:
Other CyberView Scanner manuals
