Cyclevision FANG MOUNT CVFM-01-01 User manual

INSTRUCTIONS AND SPECIFICATIONS
ITEM: FANG MOUNT®
PART NUMBER: CVFM-01-01
Revision 2 - Instruction Date 13-04-20
FANG MOUNTS®Designed, and Imported by Cyclevision Pty Ltd,
Suite 23/25 29 Grafton Street, Cairns 4879, Queensland, Australia
Post Office box 438 Brisbane, 4000, Queensland Australia
For further information, enquiries, problems and/or feedback please use either of the below
email addresses and a staff member will attend to your request as soon as possible
[email protected], [email protected] phone [phone]
Computer modelling: - Shape Labs, Level 3, Z1, The Works, 34 Parer Place, Kelvin Grove
4059, Brisbane, Australia
Manufactured: - TSC Limited, 31 Centre road, Gold hill industrial park, Ping Di Town, Shen
Zhen City, Guangdong, China
OVERVIEW
FANG MOUNTS are designed to be installed facing forward of the bicycle handlebars.
Fully articulated arms and quadruple rubber bindings ensure the FANGS securely lock and
support any size smartphone, cycle computer or cycling device aid ‘forward’ of the bicycle
handlebars.
Fully articulated arms allow you to move and separate the arms together or individually
inwards, outwards, up, down, or to the side to properly secure your device, as you wish.
Made from super strong glass filled synthetic polymers, FANGS are tough, flexible extremely
adaptable and will easily accommodate any size smartphone. FANGS have been especially
designed to unlock the Cyclevision EDGE helmet’s inspirational ability to live stream
rearwards approaching traffic, turning your smartphone screen into an electronic rear vision
mirror. In the event of a tumble FANGS fold up and out of the way preventing injury.

DESCRIPTION AND PARTS
ITEM
NUMBER
PART NUMBER
DESCRIPTION
QUANTITY
PER ARM
1
JD-1448015Z
LOWER HANDLEBAR MOUNT
1
2
JD-1448025Z
UPPER HANDLEBAR MOUNT
1
3
JD-1448035Z
RESERVABLE EXTENSION BRACKET
1
4
JD-1448045Z
PHONE MOUNT PIVOT
1
5
JD-1448053Z
RUBBER STRIP, SHORE A90
1
6
JD-1448052Z
VERTICAL SUPPORT ARM
1
7
JD1448060Z
O-RING –NITRILE
70 DURO 2mm x 57mm
2
8
AS-1420-M5x25-N G316
HEX HEAD SCREW
1
9
AS 1112.4 AB –M4N
NYLOCK NUT
5
10
AS 1237.1 S- 4
WASHER
2
11
AS-1420-M5x16-N G316
HEX HEAD SCREW
1
12
AS-1420-M5x20-N G316
HEX HEAD SCREW
3
Replacement O-rings and stainless-steel screws can be purchased from most automotive,
hardware, and fastener stores, or direct off the internet, the sizing & Durometer hardness is
indicated (item 7) same for screws & nuts, specification and sizes indicated 8, 9, 10, 11, 12
Your Fangs come loosely assembled in the packing box, however you will need to remove the
lower handlebar mount ②from the upper handlebar mount ①in order to place them either
side of the bicycle handlebars.
The following instructions assumes all parts are in a state of complete disassembly, steps may
be omitted depending on the state of disassembly
Remember the rules of the road, and that it is an offence by law in some states and countries
to use your mobile phone whilst riding. Please ensure you set the phone in the correct
position and edit phone settings before you start your ride, that way there is no need to touch
your phone while you are cycling

SETUP & ASSEMBLY INSTRUCTIONS
1. Use 5mm alley key and separate upper and lower handlebar mounts ①②
2. Wrap upper and lower handlebar mounts around the bicycle handlebars, directly either side of
the central handlebar mounting stem
3. Insert x2 hex head allen key screws ⑫through the upper mount ①and lower mount ②
4. Insert nylock nuts ⑨into lower housing nut lock cavity and turn screws ⑫to engage nuts ⑨
(do not fully tighten at this time)
5. NOTE: Fangs have been designed for use on 31.6 mm standard size road bike handlebars, use
x2 spacers ⑤inside upper & lower mounts ①& ②for handlebars that are smaller in size i.e.
25mm to 26mm in diameter, as found on some touring and trail bikes
6. Insert reversable extension bracket ③into the lower handlebar mount forward support boss ②
with the concave shape of the reversable extension bracket facing away from the centre of the
handlebars (curve towards the outside)
7. Insert hex head allen key screw ⑧through the lower handlebar mount forward support boss
and through the inner pivot arm spigot of the reversable extension bracket ③
8. Install nylock nut ⑨into lower housing nut lock cavity and turn screw ⑧to engage nut
(do not fully tighten at this time)
9. Insert phone mount pivot ④over the outer spigot of the reversable extension bracket with the
twin gaps facing outwards
10. (ensure the rounded side of the phone mount pivot ④is facing up to accommodate the round
hex head allen key screw and the six-sided nut lock cavity is facing down)
11. Install hex head allen key screw ⑪trough the phone mount pivot ④
12. Insert nylock nuts ⑨into lower nut lock cavity and turn screws ⑪to engage nuts ⑨
13. Install x2 O-rings ⑦over each of the inner and outer sides of vertical support arm ⑥
14. (ensure the two O-rings ⑦sit inside the spigot arm gap of the vertical arm ⑥)
(Note: the O-rings will extend outwards from each side of the lower portion of the vertical
support arm lock (hook) out along the arm and onto the outer central recess of the arm)
15. Install vertical support arm lower spigot into the twin gaps of the phone mount pivot ④
16. Install Hex head Allen key screw (with one washer ⑩under the head, through the phone mount
pivot bore engaging the lower spigot bore of the vertical support arm
17. Install washer ⑩under the nut ⑨
18. Insert nylock nuts ⑨into lower housing nut lock cavity and turn screws ⑫to engage nuts ⑨
(do not fully tighten at this time)
19. Position the upper and lower handlebar mounts ①and ②hard against the larger portion of
the handlebars directly either side of the handle bar stem.
20. Set the angle of the Fangs so the upper and lower handlebar mounts are equal horizontal (or as
desired) and tighten both hex head allen key screws ⑫until the upper and lower handlebar
mounts are firmly secured to the handlebars
21. Tighten screws ⑧and ⑪so the reversable extension bracket ③and phone mount pivot ④
are secured, but still moveable under firm pressure
22. Hold nut ⑨on the lower portion of the vertical support arm and tighten hex head allen key
screw ⑫until the vertical support arm is secured but still moveable
23. (do same for opposite arm)
Your Fangs are now ready for phone insertion
24. Place phone or device into the lower locks of the vertical support arms, secure with x4 O-rings
25. Adjust the pivot angles of the reversable extension bracket ③and/or the Phone Mount Pivot ④
inwards, outwards or sideways to meet your specific Phone or device dimensions
(Note: the preferred mounting will be about a 15mm to 20mm from either side/end of your
smartphone)
26. Set you Phone at your preferred angle of viewing by moving the Phone vertical support arms ⑥
up or down
27. When slipping the O-rings up and over your phone take care to avoid the phone function
buttons on the side of your phone and your good to go
(Note: further information and FANG MOUNT set up can be found on Cyclevision Website)