Cycling Sports Group DT-3267 User manual

UNIVERSAL SPINNER BIKE CONSOLE
INSTRUCTION MANUAL
DT-3267 SPINNER BIKE CONSOLE SPECIFICATION
CADENCE BAR GRAPHIC: 0~199rpm
RPM : 0 ~ 199 RPM
SPEED : 0 ~ 99 KM/H
PULSE : 30 ~ 240 BPM
Time : Count down setting range 1~99 Minuets
Count up range 00:01~99:59
Protocol : BLE4.0
IMPORTANT SAFETY INSTRUCTIONS WARNING
BEFORE BEGINNING THIS OR ANY OTHER
EXERCISE PROGRAM, CONSULT A PHYSICIAN. THE
PHYSICIAN CAN HELP YOU BETTER DETERMINE
WHAT ACTIVITIES OR PROGRAMS ARE MOST
SUITED FOR YOU. IF AT ANY TIME DURING THE
WORKOUT YOU FEEL FAINT, OR CHEST PAINS, OR
SEVER SHORTNESS OF BREATH, STOP
EXERCISING IMMEDIATLELY AND CONSULT A
PHYSICAN.
The Universal Spinner Bike Console assembly consists
of a computer console, a magnet, one chest belt, and a
wired speed sensor. The sensor counts the number of
times the magnet (mounted on the crank) passes the
sensor. The speed sensor connect to the console, and
measured the speed and cadence.
The computer console use AAA type batteries. Please
install the supplied AAA batteries in the computer
console before using.

ITEM Check List
Sensor Cable & Holder
Magnet
Velcro
AAA Batteries
Sponge
Cable Stripe
Clamp Bracket Set
(Heart Rate Feature Models Only)
Chest Belt
Universal Spinner Bike Console Battery
Installations:
1. Remove the battery cover from the back of
the computer.
2. Insert 2 AAA batteries into the battery
compartment and reinstall the battery cover.
3. When Battery working voltage is low, the ‘Low
battery’ indicator will show up on the Console display.
INSTALLATION OF THE UNIVERSAL
GROUP CYCLING MONITOR
This UNIVERSAL SPINNER BIKE MONITOR can be
installed onto most of Group Cycling and Spin Style
bike handlebars.
Console Installation:
1. Ensure the Console Clamp is securely mounted on
the back of the console. Insert the mounting screw
through the Console Clamp into the Console.

2. Spread the bottom of the console clamp apart, than
clamp it back together over the top center of the
handlebar.
3. Turn the screw bar downward, slightly tighten the
screw and adjust the console for optimal Visibility. Once
the console is adjusted, continue to tighten the screw
until it is securely attached to the handle bar.
Speed sensor
Depending on the make and model of the bike, the
Speed Sensor can typically be installed nearby the path
of the magnet on the crank.The other side of the speed
sensor connect to console.
Magnet
Firmly attach the magnet on the crank arm at the
measured location. The allowable maximum distance
between the magnet and sensor end is 8 mm.

HEART RATE
LOAD
LOW BETTERY
TIME
DISPLAY WINDOW
RPM
KCAL/WATT
SPEED
DISTANCE
TIME
CADENCE & SPEED
Cadence is the measurement of how fast the cranks are
rotating in RPM’s. The approximate speed of the bike
can also be display (MPH/KPH) in the section.
In addition to the MPH/KPH, the CADENCE will also
display a bar graph that allows the rider to keep track of
the approximate cadence that has been achieved.
Average Cadence or Speed will be automatically shown
after the rider stop the pedaling for 3 seconds.
DISTANCE
Distance is the measurement of the approximate
distance achieved on the bike. This distance is based on
the user riding a bike with tires that are the same size as
the bikes flywheel.
KCAL
Kcal is the approximation of calories burned during your
work out. The calories are calculated by measuring the
rider’s instantaneous heart rate, gender, and tension
level.
HEART RATE (apply to HR featured models only)
This is the approximation of heart rate detect from the
chest belt during the work out. Average Heart Rate will
Time is the length of time (min. / sec.)
The time will count up or count down during user
peddling. When pedalling stopped, the time will stop to
count up or count down after 3 seconds.
be automatically shown after 3 seconds if the console
cannot detect the current Heart Rate.

Resetting all measured value
To clear all the measured values, press and hold
MODE key under ALL Mode for 6 seconds. All the
measured value for AVG SPEED, AVG RPM, AVG
PULSE, TIME, DIST, KCAL will reset to zero.
TIMER Setting
The TIMER displays us ser ＇exercise-workout time. If
the user does not set the COUNT DOWN TIME, the
TIME will count up from 00:00 to 99:59.
If user prior set the COUNT DOWN TIME, the TIME will
count down to zero with flashing display and Alarm
automatically from counting down to counting up from
00:01. The user can go into TIMER setting from SPEED,
DISTANCE or TIME Mode by press and hold｀PAGE＇key
for 6 seconds.
QUICK Start
In Power Saving Mode, Press Page Key will bring the
CONSOLE to ‘QUICK Start’ active state.
Power Saving Mode QUICK START Mode
MODE SELECT
Press ‘MODE’ key to select the TIME, DIST, KCAL
display.

HEART RATE TARGET ZONES
Under the DIST or TIME, hold Page key for 6 seconds to
go into the setting, Press ‘MODE’ key to set high, low heart
rate limit.
Press the PAGE key to increase maximum heart rate
limit. After setting the maximum heart rate, press the
MODE key to adjust the minimum heart rate limit.
PERSONAL DATA SETTING
Lb/Kg setting
1. Press the Page key to go to the weight unit setting.
Press the Mode key to select the weight, either: Kg.
/ Lb. Note: this change of metric units to imperial
units will affect the displaying units: MPH/KPH,
Lb/KG and ML/KM.

TROUBLESHOOTING
No Display on Console
1. Press any key to bring the console to ‘Quick Start’
mode.
2. Ensure that the batteries are installed properly
in the Console. If they are, install fresh batteries.
No Heart Rate signal displayed
1. Ensure that your chest strap is worn correctly, and
that there is moisture under the electrodes of the
chest strap.
2. Relocate the bike away from any equipment that
could potentially interrupt the radio frequency signal,
such as a DVD player or television, etc.
RPM or HR does not change
1. Press ‘MODE key’ repeatedly to toggle between
SPEED (SPD), DISTANCE (DIST), TIME (TIME)
and CLOCK (CLK) values.
2. Press and Hold ‘MODE key’ repeatedly to clear
past measured value or go into setting and exit.
Rate signal gets interrupted or drops out
1. Ensure that there is a minimum distance of
36 inches between bikes.
2. Verify that your chest strap is secure and that the
electrodes are making contact with your chest at all.

CAUTION
EXTERNAL INTERFERENCE MAY BE CAUSED BY
OTHER ELECTRONIC DEVISES, SUCH AS:
NEARBY TELEVISIONS, STEREO EQUIPMENT,
SPEAKERS, ELECTRICAL WIRE CABLING, ETC.
IF YOU EXPERIENCE DISTURBANCES IN THE
CONSOLE DISPLAY TRY MOVING YOUR BIKE (S)
AWAY FROM POTENTIAL RF INTERFERENCE
AREAS.
WARRANTY
This is to certify that the Universal Group Cycling
Monitor is warranted by Direction Technology to be free
of all defects in materials and workmanship. This
warranty does not apply to any defect caused by
negligence, misuse, accident, alteration, improper
maintenance, or an ‘act of God.’ The Universal Group
Cycling Monitor can be adapted to almost any indoor
cycling or spinning bike. The Universal Group Cycling
Monitor carries a one-year warranty on the monitor,
chest belt, and transmitter.
Batteries are not warranted. Contact our Customer
Service Department to report any problems.
When calling, please be prepared to provide the
customer service representative with the following
warranty replacement parts are shipped, you may be required
to return the defective part. We reserve the right to make
changes and improvements in our products without incurring
any obligation to similarly alter products previously purchased.
In order to maintain your product warranty and to ensure the
safe and efficient operation of your monitor, only authorized
Direction Technology replacement parts can be used.
PLEASE NOTE:
1The Universal Group Cycling Monitor system are
designed as sealed units and not meant to be
opened other than for the sole purpose of installing
batteries. Any opened units will void the warranty.
2To clean the Universal Group Cycling Monitor system,
lightly spray the monitor with an authorized cleaning /
disinfectant solution and wipe dry with a soft towel.
Use of any caustic cleaning solutions will void the
warranty.
3The Universal group Cycling Monitor system is
NOT waterproof, only water resistant. Any
excessive exposure to water will void the warranty.