Cyclops Marine smartlink Nano User manual

[e-mail] smartlink guide issue 9 EN
smartlink Guide
For load display, see ‘App Instructions’ and ‘Gateway Instructions’ before sensor installation.
Product Description
smartlinks are wireless load sensors, manufactured in titanium to be the lightest, strongest and smallest load sensors on the
market. Designed in collaboration with leading race teams, smartlink will help you measure and repeat your fast settings
every time.
How it works…
Simply add inline of any ‘soft’ stay or sheet. Easily connect the sensor to your phone via the latest smartphone app or to
marine electronics via optional NMEA2000 gateway for immediate load data.
Correct loading with soft lines
smartlink is designed to be loaded inline with soft
lines/rope/strops, for the most accurate load
measurement. If smartlink is loaded in a bridle
configuration the displayed load will be inaccurate.
Figure 1 Incorrect and correct strop loading
Use of metal shackles/pins directly on smartlink is not
advised as it may mark the titanium body and could cause
permanent damage.
Strops
The strops used for final calibration are built using wound
Dyneema cored basket loops, to the below finished
diameter. Cyclops Marine recommends using strops built
to this diameter to achieve the stated ±1% of maximum
working load (MWL) accuracy.
Contact us for pricing and availability of strops.
Model
Nano
2t
5t
10t
20t
Finished
Diameter (mm)
4.0
9.0
10.7
12.4
15.0
Safety
Please read all instructions before using smartlink to
measure loads. Always perform a safety evaluation
before use to ensure that use of the sensor is not
dangerous to nearby people or property.
smartlink is not intended to support personnel working
aloft. Please follow all standard working aloft safety
procedures.
Overload
The MWL of a smartlink must not be exceeded, as this
may cause damage to the internal instrumentation and
will invalidate the warranty.
SHOCK LOADING (i.e. strop failure) OR OVERLOADING TO
150% OF MWL WILL RESULT IN PERMANENT DAMAGE TO
THE SENSOR THAT WILL REQUIRE RECALIBRATION
Calibration
If smartlink has been under load for a significant length
of time, the sensor may take 1-2 minutes to return to zero
when the load is removed. This is to be expected.
A significant impact to the body of the sensor can affect
the calibration. This would require the device to be
returned to Cyclops for inspection and re-calibration.
smartpower button
To maximise battery life, the sensor will be powered on
for different lengths of time depending on how many
times the power button is pressed. A single firm button
press will result in a single light flash.
Press button:
Light flashes
Powered on for:
Once
Once
30 sec
Twice
Twice
20 min
3 times
3 times
2 hrs
4 times
4 times
8 hrs
5 times
5 times
Continuous
If the sensor is on, press the button once to power it
down after 30 seconds.

[e-mail] smartlink guide issue 9 EN
Changing the CR2032 battery
FAILURE TO MAINTAIN THE BATTERY COVER SEAL WILL
RESULT INWATER INGRESS & PERMANENT DAMAGE NOT
COVERED UNDER WARRANTY.
Cyclops recommends Renata batteries for maximum
battery life and performance.
The sensor will show 0.00 as the load (even when under
load) when the batteries need to be replaced.
Cyclops recommends removal of the battery from the
device and storage of the sensor in a cool, dry place away
from direct sunlight during extended periods of time
where it is not expected to be used.
Please dispose of used batteries responsibly.
Removing battery & cover
Use a coin that fills the battery cover slot and twist the
coin until the battery cover pops out and comes
completely free. If necessary, free the battery with a
gentle tap to the opposite face of the sensor.
Replace the CR2032 battery with equivalent. Do not use
non-standard batteries or other sizes, as this can cause
damage.
Replacing battery & cover
To reinstall the battery & cover, install battery +ve side
up, insert cover, line up the arrow on the cover with the
diagonal dash on the housing. Press firmly so the cover is
flush with the housing. Use a coin to twist the cover until
the arrows in the cover are aligned, and the battery cover
is flush with the housing.
Technical Data
*Accuracy range achieved using Cyclops Marine supplied
strops.
Frequency 1Hz (custom available on request)
Accuracy ±1% of MWL within 0-40ºC
Body Material Al6082-T6 (600kg), Ti6Al4V (2, 5, 10,
20 tonne)
Housing Material Acetal, IP67 rated
Battery life 200 hours, 1x CR2032
smartlinks are not warranted to be accurate for the
purposes of buying/selling products by weight.
Model
MWL
tonnes
Dimensions
mm
Mass
g
Accuracy range*
kg
nano
0.6
64x55x17
80
±6
2t
2
79x55x19
160
±20
5t
5
83x66x22
210
±50
10t
10
93x74x25
360
±100
20t
20
107x88x39
770
±200