Cygolite TridenX 1300 User manual

•1300 lumen LED light output
•3 High-brightness 2nd Generation Cree XM-L LEDs
•8 versatile lighting settings
Boost > High > Med > Low
> SteadyPulse > Daylight Flash > Slow Flash > Walking
•OSP (On-Site Programmable) Technology
•CrossFire Technology for wider visibility
•High capacity Li-ion battery
•Light mode and battery level indicator
•Locktite tool-free handlebar mount
•Helmet mount kit
OPERATION MANUALOPERATION MANUAL
OPERATION MANUALOPERATION MANUAL
OPERATION MANUAL
Congratulations on your purchase of the TridenX high-brightness LED
headlight system. Please refer to this guide to operate your TridenX
safely and properly.
Triple LED Rechargeable Smart Bicycle Light
If you have more questions that are not listed here,
visit the support page at: www.cygolite.com
CAUTION:
· Headlight may get hot during use. Use caution when handling.
· Unplug the headlight from charger when not in use.
· Unplug connectors by the plug, never by the cable.
· Do not modify or substitute any parts with non-Cygolite parts.
· Do not open headlight case.
· Provide adequate airflow to the headlight to cool during use.
· If the light is on & stationary longer than 10 minutes, turn it off.
· Do not look directly at light.
· Do not operate or submerge under water.
· Do not operate the light unattended.
· Keep headlight away from combustible materials.
· Do not package headunit when hot or immediately after use.
· Carrying a flash light is recommended.
· This light is for bicycle use only.
· State laws regarding flashing bicycle lights may vary among states. Use the flashing
modes in accordance to your local state laws as well as federal law.
TRIDENX 1300
FEATURESFEATURES
FEATURESFEATURES
FEATURES
CONTENTSCONTENTS
CONTENTSCONTENTS
CONTENTS
F.A.Q.sF.A.Q.s
F.A.Q.sF.A.Q.s
F.A.Q.s
The TridenX is designed to be used on bikes in some of the most extreme
outdoor conditions. Over time, dust and dirt may hinder the connections on
your battery and headlight. To prevent this from happening, ensure that
both the battery and headlight are clean after every ride.
Wipe the headlight and battery down with a damp cloth. Do not submerge
the battery or headlight in water. The DC jack grommet on the headlight
occasionally needs lubrication. We recommend using a bit of vaseline to
ensure easier connection between the plug and headlight. Remove all dirt
around or on the plugs or jacks on both the battery and headlight.
The High-Brightness LEDs have extensive life so bulb replacement is not
required.
CARECARE
CARECARE
CARE
The headlight will not turn on.
•Make sure the power button was firmly pressed.
•Make sure the battery cable is properly connected.
•Make sure the battery is fully charged.
The headlight turns off over rough terrain.
•Make sure battery cable is securely plugged into the headlight.
•Make sure battery cable is fastened to the handlebar to
minimize cable vibration.
TROUBLESHOOTINGTROUBLESHOOTING
TROUBLESHOOTINGTROUBLESHOOTING
TROUBLESHOOTING
WARRANTYWARRANTY
WARRANTYWARRANTY
WARRANTY
CYGOLITE
1307-A EAST SAINT GERTRUDE PL., SANTA ANA, CA 92705 USA
PHONE: [phone] EMAIL: [email protected]
www.cygolite.com
All Cygolite products are backed by Cygolite’s warranty, providing
quality, craftsmanship, and the assistance of our knowledgeable staff.
If any support is needed, we will assist with 48 hour turnarounds on parts
and service. For questions, problems, and/or authorized Cygolite parts
contact us.
COMMITMENTCOMMITMENT
COMMITMENTCOMMITMENT
COMMITMENT
• High-brightness LED headlight
• Rechargeable Li-ion battery
• Wall charger
• Locktite handlebar bracket
• Helmet mount kit
• Operation manual
Q: When should I replace the bulbs?
· The LEDs have extensive life so bulb replacement is not
necessary.
Q: When should I charge my battery?
·The battery can be charged any time, but we recommend
fully charging the battery every time you charge it.
Q: Can I leave my battery on the charger for extended periods of
time?
· The wall charger prevents damage from overcharging but,
like all electrical appliances, we recommend unplugging the
battery and charger once the battery is fully charged.
Q: Can I give a partial charge to my battery?
· In order for the battery level indicator to be accurate we
recommend fully charging the battery every time.
Q: How do I know the charger is charging?
·When the wall charger is plugged into the wall outlet and
connected to the battery, the LED charging indicator on the
charger will be RED, indicating it is in Rapid charge mode.
If the LED shows GREEN, the charger is in trickle mode
and the battery is fully charged.
Q: Are other batteries interchangeable with this light?
·No, the TridenX is only compatible with the Li-Ion battery it
came with. This light is not compatible with any other
batteries.
Q: Will chargers for my other Cygolite systems recharge the TridenX
battery?
·Yes, the TridenX battery is compatible with CygoLite’s 7.6
volt Li-Ion charger used on the Centauri, and Turbo (7.6v)
systems.
Q: Can I use non-Cygolite parts for this unit?
·No, Cygolite parts are manufactured to specific quality
specifications. Use of non-Cygolite parts will void the
warranty and may cause damage to the light.
Q: Can I use this light for activities other than cycling?
·No, this light is specifically intended for bicycle use only.
QUESTIONS ABOUT ADJUSTING BRIGHTNESS / FLASH SPEEDS
Q: Can I reset my light back to manufacture default setting?
·Yes, when the light is on, press and HOLD the power
button for 7 SECONDS. The light will turn off, then restart
with the factory default settings.
Q: Are my programmed settings going to be saved after I unplug the
battery?
·Yes, your programmed settings will be saved until you
press the OSP button.
Q: Why can’t I adjust the Boost brightness or Walking mode?
·Those 2 modes are permanent and can not be programmed.
Q: What if I don’t want to program the light, can I use it normally?
·Yes you can use the light with the factory default settings
it came with.
In the USA, the TridenX comes with a one year limited warranty against any
defective part or craftsmanship. The battery is warranted up to 180 days
after the original date of purchase. If the unit is under warranty, Cygolite
will repair or replace defective components at no charge provided the
product has not been subject to misuse, abuse, or non-Cygolite authorized
alteration, modification or repair. Warranted products requiring service
must receive a Return Merchandise Authorization number (RMA#) from
customer service. The original receipt (INCLUDING DATE) is required on
all warranty repairs. Shipping costs inccurred from shipping warranty or
repair items from the customer to Cygolite are covered by the customer.
For warranty issues outside the USA, contact the retailer where the
purchase was made.
V1:130820

The TridenX features a BICYCLING MODE with 4 brightness mode, and a
SPECIAL MODE with 3 flashing, and a walking mode. These modes are
controlled by the power button and OSP button on the top of the headlight.
On top center of the headlight are 4 indicators that show which setting the
headlight is in with the rear indicator also functioning as a battery level
indicator. The diagram and instructions below indicate where these features
are located on the headlight and how to properly use them.
CAUTION: The light may get hot during use. Handle with care and turn
light off if stationary for more than 10 minutes.
CUSTOMIZE LIGHT SETTINGS
OSP is the first smart technology by Cygolite that gives you the freedom
to customize your preferred brightness settings and flashing speeds directy
to your headlight anytime, anywhere. You can use the factory default
settings or use the OSP button to customize your preferred settings.
NOTE: Boost mode and Walking mode are non-adjustable.
WARNING: Use discretion when programming the TridenX while riding. Do
not program your light during times that require total attention. Cygolite
cannot be held responsible for injuries that may occur during riding.
TO RESTORE FACTORYDEFAULT SETTINGS
While the light is ON, press and HOLD the power button for 7 seconds. The
light will turn off, then turn back on with the factory default settings.
THERMAL PROTECTION
The TridenX features a built in thermal protection to prevent the light from
overheating. The thermal protection will automatically dim the light (approx. 15%
brightness reduction) until the light cools to a normal operating temperature. At
that time, the light will return to its normal brightness.
HEADLIGHT OPERATIONHEADLIGHT OPERATION
HEADLIGHT OPERATIONHEADLIGHT OPERATION
HEADLIGHT OPERATION
MOUNTING BATTERYMOUNTING BATTERY
MOUNTING BATTERYMOUNTING BATTERY
MOUNTING BATTERY
1. An adhesive foam pad is included to provide cushion and grip between
the battery and the bike.Apply the foam padding to the center of the
battery above the velcro slot.
2. Thread the velcro strap through the velcro slot
3A (Stem mount). Wrap velcro strap around stem, through plastic loop,
and fasten to itself
3B (Frame mount). Wrap velcro strap around frame, through plastic loop,
and fasten to itself
BATTERYMOUNTING PRECAUTIONS: When mounting the battery to the
bike, make sure the battery cable and battery velcro strap do not interfere
with the brake cables or the ability to turn the handlebars.
TO REMOVE HEADLIGHT FROM THE HANDLEBARS
1. Press tab on bracket plate forward.
2. Slide headunit up.
TO ADJUST THE SIDE-TO-SIDE BEAM DIRECTION
Roll the headlight left to right to adjust the side-to-side direction.
POWER BUTTON
LIGHT MODE
INDICATORS
BATTERYLEVEL
INDICATOR
Power In
DC JACK
Turn ON
BICYCLE MODE (4)
Boost >High > Med > Low
PLUG battery cable
into headlight DC Jack
(or from off position)
PRESS Power button
SPECIAL MODE (4)
SteadyPulse > Day Flash > Slow Flash > Walking
(From off position)
PRESS power button for 2 seconds
and then release
PRESS Power button to scroll between modes
Press and hold OSP button to gradually change brightness (in Special
mode flash speeds change) and RELEASE the button to stop the change.
HOLD the button again to change brightness in the opposite direction. If
brightness does not change while holding, the light reached the upper or
lower limit, RELEASE and HOLD the button again to go the opposite
direction.
HOLD Power button for 2 seconds
3A
The TridenX comes with a stem mount battery (standard model) or a frame
mount battery (Xtra model). Attach battery to the bike as followed:
Stem mount 3B Frame mount
OSP BUTTON
INDICATOR
top of headlight
BICYCLE Mode
SPECIAL Mode
HIGH
DAYFLASH
MEDIUM
SLOW FLASH
LOW
WALKING
BOOST
S.PULSE
Switch
mode
Customize
mode
Turn OFF
Spacers
1
1
Rubber Pad
24
5
3
6
MOUNTING ON HANDLEBARSMOUNTING ON HANDLEBARS
MOUNTING ON HANDLEBARSMOUNTING ON HANDLEBARS
MOUNTING ON HANDLEBARS
1. Attach handlebar spacers to inside of handlebar bracket for standard
sized and remove them for oversized handlebars.
2. Swing thumbnut down from thumbnut slot to open bracket.
3. Attach rubber pad to handlebar spacer. First remove paper from
rubber pad to reveal adhesive side, align rubber pad holes to
handlebar spacer plugs and join together.
4. Wrap bracket around handlebar & return thumbnut to slotted space.
5. Twist thumbnut clockwise until tight.
6. Slide headlight downward into bracket until headlight clicks into place.
BATTERYLEVEL INDICATOR
The battery level indicator is the blue LED closest to the back of the light next
to the power button. It flashes 3 different speeds to indicate the battery levels.
Constant
with Blink
Full to
1-1/2 hour left
Full to
3/4 hour left
Fast Flash
Less than
1-1/2 hour left
Less than
3/4 hour left
Slow Flash
Less than
1/2 hour left
Less than
1/4 hour left
Headlight
flashes for
20 seconds
then turns off
Battery
Empty
TridenX Xtra
(time remaining)
TridenX
(time remaining)
Indicator
Flash sequence
Indicator
(top of headlight)
RUN TIMESRUN TIMES
RUN TIMESRUN TIMES
RUN TIMES
The run times below are based on the factory default settings. Run times
will vary if you customize the light settings.
BATTERY CHARGINGBATTERY CHARGING
BATTERY CHARGINGBATTERY CHARGING
BATTERY CHARGING
NOTE: Give the battery a full charge before using for the first time. To prolong
battery life, give the battery a 1 hour charge every 2 months it is not being used.
1. Connect the charger to wall outlet first then the battery to the charger
(Follow sequence for proper charging.)
NOTE: The LED charging indicator on charger may take up to 30 seconds to
turn on after the battery and charger have been connected.
2. The LED on the wall charger shows red when charging then
green when fully charged.
3.
Allow approx. 4-8 continuous hours to fully charge a drained battery.
4. Disconnect charger and battery when charging is complete and not in
use.
Wall charger
LED charging indicator
RED=Charging
GREEN=Fully charged
WARNING: Charge the battery with the supplied charger only. Using any
other charger to charge the battery may result in damage. The Smart
Rapid charger is for indoor use only. Unplug the battery, and charger
once the battery is fully charged.
Allow approximately: 4 hours to fully charge (stem mount battery)
: 8 hours to fully charge (frame mount battery)
Battery
Outlet
HELMET MOUNTINGHELMET MOUNTING
HELMET MOUNTINGHELMET MOUNTING
HELMET MOUNTING
The TridenX can be mounted on the helmet with the included helmet mount kit.
Refer to separate helmet mounting instruction that is included with the helmet
mount kit.
LIGHT MODE INDICTORS
The 4 illuminated LEDs on the top of the headlight show which setting is in use.
NOTE: *SteadyPulse mode combines steady brightness to see and
alerting flash to be seen into one mode. It is made especially for riding at
night in high traffic areas.
TridenX 1300 Xtra
RUN TIME* (hr: min)
3:30
5
10
32
7
80
24
76
BICYCLE MODE
Boost
High
Medium
Low
SPECIAL MODE
SteadyPulse*
Day Flash
Slow Flash
Walking
(lumen)
(1300)
(900)
(650)
(150)
TridenX 1300
RUN TIME* (hr: min)
1:45
2:30
5
16
3:30
40
12
38
1Velcro Slot 2
Add Foam Pad