CYP PU-507-KIT User manual

PU-507-KIT
5-Play HDBaseT™ Extender Kit (inc. PoE & single LAN, up to 100m)
OPERATIONS MANUAL

DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer le, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2011 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sucient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE SUMMARY OF CHANGE
VS1 29/02/12 First Release
VR2 02/03/12 PoE Support (Brand only)
VS3 23/03/12 Amended PoE function
Updated the connection diagram and
the specications table
v1.01 20/09/13 Amended Link LED description
v1.02 08/10/13 Amended product description

CONTENTS
1. Introduction...........................................6
2. Applications ...........................................6
3. Package Contents ..................................6
4. System Requirements ...........................6
5. Features..................................................7
6. Operation Controls and Functions .......8
6.1 Transmitter Front and Rear Panels....... 8
6.2 Receiver Front and Rear Panels ............ 9
6.3. D-Sub 9 Pin Denitions ........................10
7. Connection Diagram .......................... 11
8. Specications...................................... 12
9. Acronyms............................................. 13

6
1. INTRODUCTION
The PU-507-KIT allows uncompressed HDMI signals and IP data to be
transmitted over a Single CAT5e/6 cable. This solution has the added
features of RS-232 and 2-way IR control functionality over the same
CAT5e/6 cable. These combined HDMI and control signals can be
transmitted up to lengths of 100 metres.
2. APPLICATIONS
Household entertainment sharing and control
Lecture room display and control
Showroom display and control
Meeting room presentation and control
Classroom display and control
3. PACKAGE CONTENTS
1×HDMI to CAT5e/6 (with LAN/IR/RS-232) Transmitter
1×CAT5e/6 to HDMI (with LAN/IR/RS-232) Reciever
1×IR Blaster
1×IR Receiver
1×24V/1.25 A DC Power Adaptor
Operation Manual
4. SYSTEM REQUIREMENTS
Input HDMI source equipment such as DVD/Blu-ray player and HDMI
equipped output display (TV or monitor).

7
5. FEATURES
v1.4 HDMI with 3D, 4k - 2k support.
HDCP & DVI compliant.
Supports HDCP repeating and CEC functions.
Uncompressed data transfer over single CAT cable (100m - CAT6; 80m -
CAT5e).
Uncompressed video 1080p, 60Hz, 48bits
Audio support up to 7.1CH & Dolby TrueHD, DTS-HD.
5Play™ convergence: HDMI, LAN, POE & Control (IR & RS232).
Supports 3D signals.
Note:
1. This system was tested with CAT-6E/23AWG cables, results may vary with
cables of a dierent specication.
2. The PoE function is designed for powering compatible receiver units
only—non-PoE receivers will need their own power supply.Receivers of
another brand may not be compatible.

8
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Transmitter Front and Rear Panels
RearFront
RS-232 In
LAN
HDMI In
HDMI to CAT5e/6 with LAN/IR/RS232
Transmitter
CAT5e/6 Out
Link
IR2 Extender
IR1 Blaster
DC 24V
Power
2 31 64 7 8 95
1
HDMI In: Connect to HDMI source equipment such as a DVD or Blu-
ray player.
2
LAN: Connect to an internet or network connection.
3
RS-232 In: Connect to a PC or laptop with D-Sub 9 pin male cable for
the transmission of RS-232 commands.
4
Power LED: This blue LED will illuminate when the device is
connected to a power supply.
5
DC 24V: Plug the 24V DC power supply into the unit and connect the
adaptor to an AC outlet.
6
IR 1 Blaster: Connect to the supplied IR blaster cable for IR signal
transmission. Place the IR blaster in direct line-of-sight of the
equipment to be controlled.
7
IR 2 Extender: Connect to the supplied IR receiver cables for IR signal
reception. Ensure that remote being used is within the direct line-of-
sight of the IR extender.
8
Link LED: The yellow LED will illuminate when both the input and
output signals are connected through the CAT cable. When it blinks
regularly it indicates the source is NOT sending a signal to the
transmitter but the transmitter and receiver are linked. If it blinks
irregularly it indicates an error has occurred.
9
CAT5e/6 Out: Connect to the reciever unit with a Single CAT5e/6
cable for tranmission of all data signals.

9
6.2 Receiver Front and Rear Panels
RS-232 Out
LAN
HDMI Out
CAT5e/6 to HDMI with LAN/IR/RS232
Receiver
RearFront
CAT5e/6 In
Link
IR1 Extender
IR2 Blaster
Power
2 31 65 7 84
1
HDMI Out: Connect to a HDMI equipped TV/monitor for display of the
HDMI input source signal.
2
LAN: Connect to a PC or Laptop to the Internet or network
connection.
3
RS-232 Out: Connect to the device that is to be controlled (via D-Sub
9 pin female cable) by RS-232 commands.
4
Power LED: This blue LED will illuminate when the device is
connected to a power supply.
5
IR 2 Blaster: Connect to the supplied IR blaster cable for IR signal
transmission. Place the IR blaster in direct line of sight of the
equipment to be controlled.
6
IR 1 Extender: Connect to the supplied IR receiver cables for IR signal
reception. Ensure that remote being used is within the direct line-of-
sight of the IR extender.
7
Link LED:The yellow LED will illuminate when both the input and
output signals are connected through the CAT cable. When it blinks
regularly it indicates the source is NOT sending a signal to the
transmitter but the transmitter and receiver are linked. If it blinks
irregulaly it indicates an error has occurred.
8
CAT5e/6 In: Connect to the transmitter unit with a Single CAT5e/6
cable for tranmission of all data signals.

10
6.3. D-Sub 9 Pin Denitions
Pin Dene TX / RX
1 N/C
2 TxD / RxD
3 RxD / TxD
4 N/C
5 GND
6 N/C
7 N/C
8 N/C
9 N/C

11
7. CONNECTION DIAGRAM
TV or Monitor
RS-232 In
LAN
HDMI In
HDMI to CAT5e/6 with LAN/IR/RS232
Transmitter
CAT5e/6 Out
Link
IR2 Extender
IR1 Blaster
DC 24V
Power
CAT5e/6 In
Link
IR1 Extender
IR2 Blaster
Power
RS-232 Out
LAN
HDMI Out
CAT5e/6 to HDMI with LAN/IR/RS232
Receiver
1.5m
1.5m
1.5m
60°
1.5m
60°
7m3m 3m
60°
7m3m 3m
60°
RS-232 Equipped
PC or Notebook
RS-232 Equipped
HDMI Switcher
Notebook
DVD or Blu-ray Player
Internet Modem or
Router
Power
Supply
IR Blaster
HDMI
CAT5e/6
RS-232
HDMI
IR Extender
IR Extender
IR Blaster RX
TX
CAT5e/6
RS-232

12
8. SPECIFICATIONS
Video Bandwidth 300 MHz/9 Gbps
Ethernet Speed 100 Mbps
Transmitter
Input 1×HDMI, 1×IR Extender,1×RS-232, 1×LAN
Output 1×CAT5e/6, 1×IR Blaster
Receiver
Input 1×CAT5e/6, 1×IR Extender
Output 1×HDMI, 1×RS-232, 1× IR Blaster, 1× LAN
HDMI In/Out Cable
Distance
Up to 10 Meters
CAT6 In/Out Cable
Distance
Up to 100 Meters
HDMI In/Out Supports
Resolution
480i~1080p@50/60, 1080p@24,
VGA~WUXGA
IR Frequency 30~50 kHz
ESD Protection Human Body Model:
±8 kV (air-gap discharge)
±4 kV (contact discharge)
Power Supply 24V/1.25 A DC (US/EU Standards, CE/FCC/
UL certied)
Dimensions 102 mm (W)×113 mm (D)×25 mm (H)/TX
102 mm (W)×107 mm (D)×25 mm (H)/RX
Weight 252 g (TX), 256 g (RX)
Chassis Material Aluminum
Silkscreen Color Silver
Power Consumption 13 W
Operating Temperature 0 °C~40 °C/32 °F ~104 °F
Storage Temperature −20 °C~60 °C/−4 °F~140 °F
Relative Humidity 20~90 % RH (non-condensing)

13
9. ACRONYMS
ACRONYM COMPLETE TERM
CAT5e Category 5 Cable
CAT6 Category 6 Cable
CEC Consumer Electronics Control
DVI Digital Visual Interface
HDCP High-bandwidth Digital Content Protection
HDMI High Denition Multimedia Interface
IR Infrared

CYP (UK) Ltd., Unit 7, Shepperton Business Park, Govett Avenue, Shepperton,
Middlesex, TW17 8BA
Tel: [phone] | Fax: [phone]
Email: [email protected]
www.cypeurope.com
v1.02