CYP PU-16HBT User manual

PU-16HBT
16 x 16 HDMI HDBaseT™ Matrix including PoE
OPERATION MANUAL

3
DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer le, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2011 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

4
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sucient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE SUMMARY OF CHANGE
v1.00 08/10/13 First release
v1.01 08/11/13 Added 'IR ALL In/Out'

5
CONTENTS
1. Introduction...........................................6
2. Applications ...........................................6
3. Package Contents ..................................6
4. System Requirements ...........................6
5. Features..................................................7
6. Operation Controls and Functions .......8
6.1 Front Panel................................................... 8
6.2 Rear Panel...................................................10
6.3 RS-232 Protocols......................................11
6.4 RS-232 & Telnet Command...................12
6.5 Telnet Control............................................15
6.6 Web GUI Control ......................................17
7. Connection Diagram .......................... 19
8. Specications...................................... 20
8.1 Technical Specications ........................20
8.2 CAT5e/6/7 Cable Specication ...........21
9. Acronyms............................................. 22

6
1. INTRODUCTION
The NEW PU-16HBT modular matrix oers unparalleled levels of exibility
and performance for systems integrators and installers in any multi-zone
AV environment. Utilising the latest HDBaseT™ technologies, this device
allows switching and distribution of 16 HDMI sources, 2-Way IR, RS-232,
and PoE (Power over Ethernet) to lengths of up to 100m using CAT5e/6/7
cable infrastructure. This modular matrix is pre-congured with 16
HDBaseT outputs designed to be used with PU-507-RX or PU-507-WPRX
Receivers which are powered using the PoE feature of the matrix. The PU-
16HBT is supplied with dual removable internal PSU's which allow for easy
inspection and maintenance with zero down time. Also included is a DVI
output for a local monitor allowing installers to easily monitor, test, and
congure the Inputs and Outputs on installation. This solution will enable
installers to condently integrate a sixteen zone multi-room AV system.
In addition, this matrix also features IP control allowing users to access
and control the matrix remotely and also allow additional options for
integration of third-party control systems such as Demopad.
Finally this matrix has RS-232 routing allowing integrators to send bespoke
RS-232 commands to individual RS-232 outputs on the PU-507RX and PU-
507WPRX receivers. These control messages can also be sent via Telnet/IP
commands meaning the matrix can act as an IP to RS-232 converter.
2. APPLICATIONS
Public information display
Educational demo
Professional Presentation
Advertising display
Hospital Operation Room
Residential Custom Install
3. PACKAGE CONTENTS
16x16 HDBaseT Matrix
2 x Power Cord
Operation manual
4. SYSTEM REQUIREMENTS
Source equipment like PC/Laptop/DVD/Blu-ray player and output to
display TVs/monitors via CAT5e/6/7 HDBaseT receivers.

7
5. FEATURES
HDMI, HDCP and DVI compliant
Supports uncompressed video/audio up to 10.2Gbps
Common supported resolutions : HDTV: 480i, 480p, 576i, 576p, 720i,
720p, 1080i, 1080p, 1080p24; PC: VGA, SVGA, XGA, WXGA, SXGA, UXGA,
WUXGA.
High Denition Audio supported: Dolby TrueHD, Dolby Digital Plus
and DTS-HD Master Audio plus LPCM (up to 192kHz)
Uncompressed data transfer over single CAT cable (100m - CAT6/7;
80m - CAT5e)
Supports control via RS-232, IR, and Manual Selection Buttons
Supports HDMI input up to 15m 1080p 8bit or 10m 1080p 12bit
Supports RS-232 for Matrix Control, plus RS-232 pass-through: Third-
party devices can be controlled in each zone via RS-232 from the head-
end to the receiver, or head-end devices can be controlled via RS-232
from any receiver in any zone.
Advanced EDID management settings
Onboard Operating Temperature Diagnostics
Recall function allows users to save up to 10 pre-congured Input/
Output settings
Supports 3D signals
Supports full IP control via Telnet or web GUI

8
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
POWER RETURN 789LOCK
MENU
PAGE 6
5
4SAVE
3
2
1RECALL
ALL
PAGE +
0
OUT/IN ENTER
LOCK
STANDBY
6
10 11 12 13
8
7
9
2
1
3 54
1POWER button & LED: Press this button to turn On the device or
press it again to switch to standby mode. The LED will illuminate
when the power is in standby mode. If the LED is ashing it means
the temperature inside is too high and air circulation may have been
restricted.
2LOCK button & LED: Press this button to lock all the function buttons
on panel. The LED will illuminate, to unlock press it again.
3RETURN: Press this button to return back/exit the current selection.
4MENU: Press this button to enter into the menu selections of
A. EDID
1. Standard EDID: Use the built-in EDID which supports video
up to 1080p@60/WUXGA@60RB and audio supports LPCM 2CH.
2. Manual EDID: Support independent EDID by appoint input
and output ports.

9
B. IP
1. IP address,
2. Netmask,
3. Gateway.
C. Temperature
1. Temperature 1,
2. Temperature 2, these gures shows the temperature of the
device inside.
D. LCM Contrast Range from 1~4
5LCM: Displays the setting information of each input and output and
other setting information according to the selection.
6PAGE▲▼◄►:Use these buttons to ip the LCM’s page for
displaying the current I/O status or when entering into the menu for
detail selection.
7SAVE: Press this button to save the present setting of the I/O.
8RECALL: Press this button to recall from the saved settings.
9ENTER: Press this button every time to conrm the setting or the
selection.
10 ALL: Press this button to select all outputs to one input.
11 OUT/IN: Press this button to select the input source to display on
output display. The sequence should be OUT/IN→number(s) for
output source→OUT/IN→a number for input display→Enter.
12 0~9: Press these numbers when selecting input output ports.
13 +: Press this button when selecting more than one output for an input
selection. This button works correspondingly with OUT/IN button
only.

10
6.2 Rear Panel
RS232 ETHERNET IR ALL
OUT IN
SERVICE OUTPUT 0IR IN
4 5
1
2
3
1OUTPUT 1~16: Connect to HD or 3D TV/monitors via CAT cables to
compatible receivers.
2CPU
a. RS-232: Connect with D-Sub 9-pin cable from the PC/Laptop device
for RS-232 control over the Matrix or other connecteddevice(s).
b. CONTROL: Connect to an active network line for Telnet/Web GUI
control.
c. ALL IR OUT: Connect to the IR blaster for IR signal transmission of
the source or display equipment. Place the IR blaster in direct line-
of-sight of the equipment to be controlled.
ALL IR IN: Connect to the IR extender for IR signal reception of
the remote control of the source and display equipment. Ensure
that remote being used is within the direct line-of-sight of the IR
extender.
d. IR IN: For control of the matrix only.
e. SERVICE: This port is reserved for rmware update only.
f. OUTPUT 0: Connect to DVI/HDMI (with DVI to HDMI adaptor)
monitor/TV for instant output image viewing.
3INPUT 1~16: Connect up to 16 source devices such as Blu-ray/PS3
players with HDMI cables.
4POWER & POWER Supply: The device will automatically turn ON
when connecting with power supply.
5Ventilation Fan: This fan will automatically turn ON when the device