Cypress MB95710M Series User manual

The following document contains information on Cypress products. The document has the series
name, product name, and ordering part numbering with the prefix “MB”. However, Cypress will
offer these products to new and existing customers with the series name, product name, and
ordering part number with the prefix “CY”.
How to Check the Ordering Part Number
1. Go to www.cypress.com/pcn.
2. Enter the keyword (for example, ordering part number) in the SEARCH PCNS field and click
Apply.
3. Click the corresponding title from the search results.
4. Download the Affected Parts List file, which has details of all changes
For More Information
Please contact your local sales office for additional information about Cypress products and
solutions.
About Cypress
Cypress is the leader in advanced embedded system solutions for the world's most innovative
automotive, industrial, smart home appliances, consumer electronics and medical products.
Cypress' microcontrollers, analog ICs, wireless and USB-based connectivity solutions and reliable,
high-performance memories help engineers design differentiatedproducts and getthem tomarket
first. Cypress is committed to providing customers with the best support and development
resources on the planet enabling them to disrupt markets by creating new product categories in
record time. To learn more, go to www.cypress.com.

MB95710M Series
MB95770M Series
New 8FX 8-bit Microcontrollers
Cypress Semiconductor Corporation • 198 Champion Court • San Jose,CA 95134-1709 • 408-943-2600
Document Number: 002-09307 Rev. *D Revised September 29, 2017
The MB95710M/770M Series is a series of general-purpose, single-chip microcontrollers. In addition to a compact instruction set, the
microcontrollers of this series contain a variety of peripheral resources.
Features
■F2MC-8FX CPU core
❐Instruction set optimized for controllers
• Multiplication and division instructions
• 16-bit arithmetic operations
• Bit test branch instructions
• Bit manipulation instructions, etc.
■Clock
❐Selectable main clock source
• Main oscillation clock (up to 16.25 MHz, maximum ma-
chine clock frequency: 8.125 MHz)
• External clock (up to 32.5 MHz, maximum machine clock
frequency: 16.25 MHz)
• Main CR clock (4 MHz ±2%)
• Main CR PLL clock
- The main CR PLL clock frequency becomes 8 MHz ±2%
when the PLL multiplication rate is 2.
- The main CR PLL clock frequency becomes 10 MHz
±2% when the PLL multiplication rate is 2.5.
- The main CR PLL clock frequency becomes 12 MHz
±2% when the PLL multiplication rate is 3.
- The main CR PLL clock frequency becomes 16 MHz
±2% when the PLL multiplication rate is 4.
•Main PLL clock (up to 16.25 MHz, maximum machine
clock frequency: 16.25 MHz)
❐Selectable subclock source
• Suboscillation clock (32.768 kHz)
• External clock (32.768 kHz)
• Sub-CR clock (Typ: 100 kHz, Min: 50 kHz, Max: 150 kHz)
■Timer
❐8/16-bit composite timer ×2 channels
❐8/16-bit PPG ×2 channels
❐16-bit reload timer ×1 channel
❐Event counter ×1 channel
❐Time-base timer ×1 channel
❐Watch counter ×1 channel
❐Watch prescaler ×1 channel
■UART/SIO ×3 channels
❐Full duplex double buffer
❐Capable of clock asynchronous (UART) serial data transfer
and clock synchronous (SIO) serial data transfer
■I2C bus interface ×1 channel
❐Built-in wake-up function
■External interrupt ×8 channels
❐Interrupt by edge detection (rising edge, falling edge, and
both edges can be selected)
❐Can be used to wake up the device from different low power
consumption (standby) modes
■8/12-bit A/D converter ×8 channels
❐8-bit or 12-bit resolution can be selected.
■LCD controller (LCDC)
❐On MB95F714J/F714M/F716J/F716M/F718J/F718M, LCD
output can be selected from 40 SEG ×4 COM and 36 SEG
×8 COM.
❐On MB95F774J/F774M/F776J/F776M/F778J/F778M, LCD
output can be selected from 32 SEG ×4 COM and 28 SEG
×8 COM.
❐Internal divider resistor whose resistance value can be se-
lected from 10 kΩor 100 kΩthrough software
❐Interrupt in sync with the LCD module frame frequency
❐Blinking function
❐Inverted display function
■Low power consumption (standby) modes
❐There are four standby modes as follows:
• Stop mode
• Sleep mode
•Watchmode
• Time-base timer mode
■I/O port
❐MB95F714J/F716J/F718J (number of I/O ports: 75)
• General-purpose I/O ports (CMOS I/O): 71
• General-purpose I/O ports (N-ch open drain): 4
❐MB95F714M/F716M/F718M (number of I/O ports: 74)
• General-purpose I/O ports (CMOS I/O): 71
• General-purpose I/O ports (N-ch open drain): 3
❐MB95F774J/F776J/F778J (number of I/O ports: 59)
• General-purpose I/O ports (CMOS I/O): 55
• General-purpose I/O ports (N-ch open drain): 4
❐MB95F774M/F776M/F778M (number of I/O ports: 58)
• General-purpose I/O ports (CMOS I/O): 55
• General-purpose I/O ports (N-ch open drain): 3
■On-chip debug
❐1-wire serial control
❐Serial writing supported (asynchronous mode)
■Hardware/software watchdog timer
❐Built-in hardware watchdog timer
❐Built-in software watchdog timer
■Power-on reset
❐A power-on reset is generated when the power is switched
on.

MB95710M Series
MB95770M Series
Document Number: 002-09307 Rev. *D Page 2 of 172
■Low-voltage detection (LVD) circuit (only available on
MB95F714J/F716J/F718J/F774J/F776J/F778J)
❐Built-in low-voltage detection function
■Comparator ×1 channel
■Clock supervisor counter
❐Built-in clock supervisor counter
■Dual operation Flash memory
❐The program/erase operation and the read operation can be
executed in different banks (upper bank/lower bank) simul-
taneously.
■Flash memory security function
❐Protects the content of the Flash memory.

MB95710M Series
MB95770M Series
Document Number: 002-09307 Rev. *D Page 3 of 172
Contents
Features............................................................................. 1
1. Product Line-up ............................................................ 4
1.1 MB95710M Series................................................. 4
1.2 MB95770M Series................................................. 7
2. Packages And Corresponding Products.................... 9
3. Differences Among Products And Notes On
Product Selection ........................................................... 10
4. Pin Assignment .......................................................... 11
5. Pin Functions (MB95710M Series) ............................ 13
6. Pin Functions (MB95770M Series) ............................ 19
7. I/O Circuit Type ........................................................... 24
8. Handling Precautions................................................. 28
8.1 Precautions for Product Design........................... 28
8.2 Precautions for Package Mounting ..................... 29
8.3 Precautions for Use Environment........................ 30
9. Notes On Device Handling......................................... 31
10. Pin Connection ......................................................... 31
11. Block Diagram (MB95710M Series)......................... 33
12. Block Diagram (MB95770M Series)......................... 34
13. CPU Core................................................................... 35
14. Memory Space .......................................................... 36
15. Areas For Specific Applications ............................. 38
16. I/O Map (MB95710M Series)..................................... 39
17. I/O Map (MB95770M Series)..................................... 45
18. I/O Ports (MB95710M Series)................................... 51
18.1 Port 0................................................................. 52
18.2 Port 1................................................................. 56
18.3 Port 2................................................................. 61
18.4 Port 4................................................................. 64
18.5 Port 5................................................................. 66
18.6 Port 6................................................................. 69
18.7 Port 9................................................................. 72
18.8 Port A ................................................................ 74
18.9 Port B ................................................................ 77
18.10 Port C .............................................................. 79
18.11 Port E .............................................................. 82
18.12 Port F............................................................... 85
18.13 Port G .............................................................. 87
19. I/O Ports (MB95770M Series)................................... 90
19.1 Port 0................................................................. 91
19.2 Port 1................................................................. 95
19.3 Port 2............................................................... 100
19.4 Port 6............................................................... 103
19.5 Port 9............................................................... 106
19.6 Port A .............................................................. 108
19.7 Port B .............................................................. 111
19.8 Port C .............................................................. 113
19.9 Port E .............................................................. 116
19.10 Port F............................................................. 119
19.11 Port G ............................................................ 121
20. Interrupt Source Table ........................................... 124
21. Pin States In Each Mode........................................ 125
22. Electrical Characteristics....................................... 131
22.1 Absolute Maximum Ratings............................. 131
22.2 Recommended Operating Conditions ............. 133
22.3 DC Characteristics .......................................... 134
22.4 AC Characteristics........................................... 139
22.5 A/D Converter................................................. 155
22.6 Flash Memory Program/Erase Characteristics 159
23. Sample Characteristics.......................................... 160
24. Mask Options.......................................................... 166
25. Ordering Information.............................................. 167
26. Package Dimension................................................ 168
Document History Page............................................... 171
Sales, Solutions, and Legal Information .................... 172

MB95710M Series
MB95770M Series
Document Number: 002-09307 Rev. *D Page 4 of 172
1. Product Line-up
1.1 MB95710M Series
Part number
Parameter
MB95F714J MB95F716J MB95F718J MB95F714M MB95F716M MB95F718M
Type Flash memory product
Clock
supervisor
counter
It supervises the main clock oscillation and the subclock oscillation.
Flash memory
capacity 20 Kbyte 36 Kbyte 60 Kbyte 20 Kbyte 36 Kbyte 60 Kbyte
RAM capacity 512 bytes 1 Kbyte 2 Kbyte 512 bytes 1 Kbyte 2 Kbyte
Power-on reset Yes
Low-voltage
detection reset Yes No
Reset input Selected through software With dedicated reset input
CPU functions
• Number of basic instructions : 136
• Instruction bit length : 8 bits
• Instruction length : 1 to 3 bytes
• Data bit length : 1, 8 and 16 bits
• Minimum instruction execution time : 61.5 ns (machine clock frequency = 16.25 MHz)
• Interrupt processing time : 0.6 µs (machine clock frequency = 16.25 MHz)
General-
purpose I/O
• I/O port : 75
•CMOSI/O :71
• N-ch open drain : 4
• I/O port : 74
•CMOSI/O :71
• N-ch open drain : 3
Time-base timer Interval time: 0.256 ms to 8.3 s (external clock frequency = 4 MHz)
Hardware/
software
watchdog timer
• Reset generation cycle
Main oscillation clock at 10 MHz: 105 ms (min)
• The sub-CR clock can be used as the source clock of the software watchdog timer.
Wild register It can be used to replace 3 bytes of data.
8/12-bit
A/D converter
8 channels
8-bit or 12-bit resolution can be selected.
8/16-bit
composite timer
2 channels
• The timer can be configured as an “8-bit timer × 2 channels” or a “16-bit timer × 1 channel”.
• It has the following functions: interval timer function, PWC function, PWM function and input capture
function.
• Count clock: it can be selected from internal clocks (seven types) and external clocks.
• It can output square wave.
External
interrupt
8 channels
• Interrupt by edge detection (The rising edge, falling edge, and both edges can be selected.)
• It can be used to wake up the device from different standby modes.
On-chip debug • 1-wire serial control
• It supports serial writing (asynchronous mode).

MB95710M Series
MB95770M Series
Document Number: 002-09307 Rev. *D Page 5 of 172
UART/SIO
3 channels
• Data transfer with UART/SIO is enabled.
• It has a full duplex double buffer, variable data length (5/6/7/8 bits), an internal baud rate generator
and an error detection function.
• It uses the NRZ type transfer format.
• LSB-first data transfer and MSB-first data transfer are available to use.
• Both clock asynchronous (UART) serial data transfer and clock synchronous (SIO) serial data transfer
are enabled.
I2C bus
interface
1 channel
• Master/slave transmission and reception
• It has the following functions: bus error function, arbitration function, transmission direction detection
function, wake-up function, and functions of generating and detecting repeated START conditions.
8/16-bit PPG
2 channels
• Each channel can be used as an “8-bit timer ×2 channels” or a “16-bit timer ×1 channel”.
• The counter operating clock can be selected from eight clock sources.
16-bit reload
timer
1 channel
• Two clock modes and two counter operating modes are available to use.
• It can output square wave.
• Count clock: it can be selected from internal clocks (seven types) and external clocks.
• Two counter operating modes: reload mode and one-shot mode
Event counter
• The event counter function is implemented by configuring the 16-bit reload timer and 8/16-bit com-
posite timer ch. 1.
• When the event counter function is used, the 16-bit reload timer and 8/16-bit composite timer ch. 1
become unavailable.
LCD controller
(LCDC)
• COM output: 4 or 8 (max) (selectable)
• SEG output: 36 or 40 (max) (selectable)
- If the number of COM outputs is 4, the maximum number of SEG outputs is 40, and the
maximum number of pixels that can be displayed 160 (4 ×40).
- If the number of COM outputs is 8, the maximum number of SEG outputs is 36, and the
maximum number of pixels that can be displayed 288 (8 ×36).
• LCD drive power supply (bias) pins: 5 (max)
• Duty LCD mode
• LCD standby mode
• Blinking function
• Internal divider resistor whose resistance value can be selected from 10 kΩor 100 kΩthrough software
• Interrupt in sync with the LCD module frame frequency
• Inverted display function
Watch counter
• Count clock: four selectable clock sources (125 ms, 250 ms, 500 ms or 1 s)
• The counter value can be selected from 0 to 63. (The watch counter can count for one minute when
the clock source is one second and the counter value is set to 60.)
Watch prescaler Eight different time intervals can be selected.
Comparator 1 channel
Part number
Parameter
MB95F714J MB95F716J MB95F718J MB95F714M MB95F716M MB95F718M

MB95710M Series
MB95770M Series
Document Number: 002-09307 Rev. *D Page 6 of 172
Flash memory
• It supports automatic programming (Embedded Algorithm), and program/erase/erase-
suspend/erase-resume commands.
• It has a flag indicating the completion of the operation of Embedded Algorithm.
• Flash security feature for protecting the content of the Flash memory
Standby mode
There are four standby modes as follows:
• Stop mode
• Sleep mode
•Watchmode
• Time-base timer mode
Package LQH080
Part number
Parameter
MB95F714J MB95F716J MB95F718J MB95F714M MB95F716M MB95F718M
Number of program/erase cycles 1000 10000 100000
Data retention time 20 years 10 years 5 years

MB95710M Series
MB95770M Series
Document Number: 002-09307 Rev. *D Page 7 of 172
1.2 MB95770M Series
Part number
Parameter
MB95F774J MB95F776J MB95F778J MB95F774M MB95F776M MB95F778M
Type Flash memory product
Clock
supervisor
counter
It supervises the main clock oscillation and the subclock oscillation.
Flash memory
capacity 20 Kbyte 36 Kbyte 60 Kbyte 20 Kbyte 36 Kbyte 60 Kbyte
RAM capacity 512 bytes 1 Kbyte 2 Kbyte 512 bytes 1 Kbyte 2 Kbyte
Power-on reset Yes
Low-voltage
detection reset Yes No
Reset input Selected through software Dedicated
CPU functions
• Number of basic instructions : 136
• Instruction bit length : 8 bits
• Instruction length : 1 to 3 bytes
• Data bit length : 1, 8 and 16 bits
• Minimum instruction execution time : 61.5 ns (machine clock frequency = 16.25 MHz)
• Interrupt processing time : 0.6 µs (machine clock frequency = 16.25 MHz)
General-
purpose I/O
• I/O port : 59
•CMOSI/O :55
• N-ch open drain : 4
• I/O port : 58
•CMOSI/O :55
• N-ch open drain : 3
Time-base timer Interval time: 0.256 ms to 8.3 s (external clock frequency = 4 MHz)
Hardware/
software
watchdog timer
• Reset generation cycle
Main oscillation clock at 10 MHz: 105 ms (min)
• The sub-CR clock can be used as the source clock of the software watchdog timer.
Wild register It can be used to replace 3 bytes of data.
8/12-bit
A/D converter
8 channels
8-bit or 12-bit resolution can be selected.
8/16-bit
composite timer
2 channels
• The timer can be configured as an “8-bit timer × 2 channels” or a “16-bit timer × 1 channel”.
• It has the following functions: interval timer function, PWC function, PWM function and input capture
function.
• Count clock: it can be selected from internal clocks (seven types) and external clocks.
• It can output square wave.
External
interrupt
8 channels
• Interrupt by edge detection (The rising edge, falling edge, and both edges can be selected.)
• It can be used to wake up the device from different standby modes.
On-chip debug • 1-wire serial control
• It supports serial writing (asynchronous mode).

MB95710M Series
MB95770M Series
Document Number: 002-09307 Rev. *D Page 8 of 172
UART/SIO
3 channels
• Data transfer with UART/SIO is enabled.
• It has a full duplex double buffer, variable data length (5/6/7/8 bits), an internal baud rate generator
and an error detection function.
• It uses the NRZ type transfer format.
• LSB-first data transfer and MSB-first data transfer are available to use.
• Both clock asynchronous (UART) serial data transfer and clock synchronous (SIO) serial data transfer
are enabled.
I2C bus
interface
1 channel
• Master/slave transmission and reception
• It has the following functions: bus error function, arbitration function, transmission direction detection
function, wake-up function, and functions of generating and detecting repeated START conditions.
8/16-bit PPG
2 channels
• Each channel can be used as an “8-bit timer ×2 channels” or a “16-bit timer ×1 channel”.
• The counter operating clock can be selected from eight clock sources.
16-bit reload
timer
1 channel
• Two clock modes and two counter operating modes are available to use.
• It can output square wave.
• Count clock: it can be selected from internal clocks (seven types) and external clocks.
• Two counter operating modes: reload mode and one-shot mode
Event counter
• The event counter function is implemented by configuring the 16-bit reload timer and 8/16-bit com-
posite timer ch. 1.
• When the event counter function is used, the 16-bit reload timer and 8/16-bit composite timer ch. 1
become unavailable.
LCD controller
(LCDC)
• COM output: 4 or 8 (max) (selectable)
• SEG output: 28 or 32 (max) (selectable)
- If the number of COM outputs is 4, the maximum number of SEG outputs is 32, and the
maximum number of pixels that can be displayed 128 (4 ×32).
- If the number of COM outputs is 8, the maximum number of SEG outputs is 28, and the
maximum number of pixels that can be displayed 224 (8 ×28).
• LCD drive power supply (bias) pins: 4 (max)
• Duty LCD mode
• LCD standby mode
• Blinking function
• Internal divider resistor whose resistance value can be selected from 10 kΩor 100 kΩthrough software
• Interrupt in sync with the LCD module frame frequency
• Inverted display function
Watch counter
• Count clock: four selectable clock sources (125 ms, 250 ms, 500 ms or 1 s)
• The counter value can be selected from 0 to 63. (The watch counter can count for one minute when
the clock source is one second and the counter value is set to 60.)
Watch prescaler Eight different time intervals can be selected.
Comparator 1 channel
Part number
Parameter
MB95F774J MB95F776J MB95F778J MB95F774M MB95F776M MB95F778M

MB95710M Series
MB95770M Series
Document Number: 002-09307 Rev. *D Page 9 of 172
2. Packages And Corresponding Products
Ο: Available
Flash memory
• It supports automatic programming (Embedded Algorithm), and program/erase/erase-
suspend/erase-resume commands.
• It has a flag indicating the completion of the operation of Embedded Algorithm.
• Flash security feature for protecting the content of the Flash memory
Standby mode
There are four standby modes as follows:
• Stop mode
• Sleep mode
•Watchmode
• Time-base timer mode
Package LQD064
LQG064
Part number
Package
MB95F714J MB95F716J MB95F718J MB95F714M MB95F716M MB95F718M
LQH080 ΟΟΟΟΟΟ
Part number
Package
MB95F774J MB95F776J MB95F778J MB95F774M MB95F776M MB95F778M
LQD064 ΟΟΟΟΟΟ
LQG064 ΟΟΟΟΟΟ
Part number
Parameter
MB95F774J MB95F776J MB95F778J MB95F774M MB95F776M MB95F778M
Number of program/erase cycles 1000 10000 100000
Data retention time 20 years 10 years 5 years

MB95710M Series
MB95770M Series
Document Number: 002-09307 Rev. *D Page 10 of 172
3. Differences Among Products And Notes On Product Selection
• Current consumption
When using the on-chip debug function, take account of the current consumption of Flash memory program/erase.
For details of current consumption, see “Electrical Characteristics”.
• Package
For details of information on each package, see “Packages And Corresponding Products” and “Package Dimension”.
• Operating voltage
The operating voltage varies, depending on whether the on-chip debug function is used or not.
For details of operating voltage, see “Electrical Characteristics”.
• On-chip debug function
The on-chip debug function requires that VCC, VSS and one serial wire be connected to an evaluation tool. For details
of the connection method, refer to “CHAPTER 26 EXAMPLE OF SERIAL PROGRAMMING CONNECTION” in “New
8FX MB95710M/770M Series Hardware Manual”.

MB95710M Series
MB95770M Series
Document Number: 002-09307 Rev. *D Page 11 of 172
4. Pin Assignment
P07/INT07/AN07/SEG30
P06/INT06/AN06/SEG31
P05/INT05/AN05/SEG32/UCK1
P04/INT04/AN04/SEG33/UI1
P03/INT03/AN03/SEG34/UO1
P02/INT02/AN02/SEG35/UCK2
P01/INT01/AN01/SEG36/UI2
P00/INT00/AN00/UO2
P16/PPG10
P15/PPG11
P14/UCK0
(TOP VIEW)
LQFP80
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
20
19
18
17
16
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
AVcc
P12/DBG
P11/UO0
P10/UI0
P53/TO0
P52/TI0/TO00
P51/EC0
P50/TO01
P13/ADTG
P22/SCL
P21/PPG01/CMP0_P
P20/PPG00/CMP0_N
P90/V4 P91/V3 P92/V2 P93/V1 P94/V0
PB2/SEG37 PB3/SEG38 PB4/SEG39
P23/SDA
PA1/COM1 PA2/COM2 PA3/COM3 PA4/COM4 PA5/COM5 PA6/COM6 PA7/COM7 PA0/COM0
PC7/SEG09
PC6/SEG08
PC5/SEG07
PC4/SEG06
PC3/SEG05
PC2/SEG04
PC1/SEG03
PC0/SEG02
PB1/SEG01
PB0/SEG00
P17/CMP0_O
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
41
42
43
44
45
P60/SEG10
Vcc
PG1/X0A
PG2/X1A
C
PF0/X0
PF1/X1
Vss
PF2/RST
PE7/SEG29/EC1 PE6/SEG28/TO10 PE5/SEG27/TO11 PE4/SEG26 PE3/SEG25 PE2/SEG24 PE1/SEG23 PE0/SEG22 P40/SEG21 P41/SEG20 P42/SEG19 AVss P67/SEG17 P66/SEG16 P65/SEG15 P64/SEG14 P63/SEG13 P62/SEG12 P61/SEG11 P43/SEG18
(LQH080)
MB95710M Series

MB95710M Series
MB95770M Series
Document Number: 002-09307 Rev. *D Page 12 of 172
P07/INT07/AN07/SEG22
P06/INT06/AN06/SEG23
P05/INT05/AN05/SEG24/UCK1
P04/INT04/AN04/SEG25/UI1
P03/INT03/AN03/SEG26/UO1
P02/INT02/AN02/SEG27/UCK2
P01/INT01/AN01/SEG28/TO00/UI2
P00/INT00/AN00/SEG29/UO2
P16/SEG30/PPG10
P15/SEG31/PPG11
P14/UCK0/EC0/TI0
(TOP VIEW)
LQFP64
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
AVcc
P12/DBG
P11/UO0
P10/UI0/TO0
P13/ADTG/TO01
P22/SCL
P21/PPG01/CMP0_P
P20/PPG00/CMP0_N
P90/V4 P91/V3 P92/V2 P93/V1
P23/SDA
PA1/COM1 PA2/COM2 PA3/COM3 PA4/COM4 PA5/COM5 PA6/COM6 PA7/COM7 PA0/COM0
P60/SEG06
PC3/SEG05
PC2/SEG04
PC1/SEG03
PC0/SEG02
PB1/SEG01
PB0/SEG00
P17/CMP0_O
48
47
46
45
44
43
42
41
40
39
38
33
34
35
36
37
Vcc
PG1/X0A
PG2/X1A
C
PF0/X0
PF1/X1
Vss
PF2/RST
PE7/SEG21/EC1 PE6/SEG20/TO10 PE5/SEG19/TO11 PE4/SEG18 PE3/SEG17 PE2/SEG16 PE1/SEG15 PE0/SEG14 AVss P67/SEG13 P66/SEG12 P65/SEG11 P64/SEG10 P63/SEG09 P62/SEG08 P61/SEG07
(LQD064)
(LQG064)
MB95770M Series

MB95710M Series
MB95770M Series
Document Number: 002-09307 Rev. *D Page 13 of 172
5. Pin Functions (MB95710M Series)
Pin no. Pin name I/O circuit
type*1Function I/O type
Input Output OD*2PU*3
1AVCC —Power supply pin for 8/12-bit A/D
converter and comparator ————
2
P07
S
General-purpose I/O port
Hysteresis/
analog
CMOS/
LCD ——
INT07 External interrupt input pin
AN07 8/12-bit A/D converter analog input pin
SEG30 LCDC SEG30 output pin
3
P06
S
General-purpose I/O port
Hysteresis/
analog
CMOS/
LCD ——
INT06 External interrupt input pin
AN06 8/12-bit A/D converter analog input pin
SEG31 LCDC SEG31 output pin
4
P05
S
General-purpose I/O port
Hysteresis/
analog
CMOS/
LCD ——
INT05 External interrupt input pin
AN05 8/12-bit A/D converter analog input pin
SEG32 LCDC SEG32 output pin
UCK1 UART/SIO ch. 1 clock I/O pin
5
P04
V
General-purpose I/O port
CMOS/
analog
CMOS/
LCD ——
INT04 External interrupt input pin
AN04 8/12-bit A/D converter analog input pin
SEG33 LCDC SEG33 output pin
UI1 UART/SIO ch. 1 data input pin
6
P03
S
General-purpose I/O port
Hysteresis/
analog
CMOS/
LCD ——
INT03 External interrupt input pin
AN03 8/12-bit A/D converter analog input pin
SEG34 LCDC SEG34 output pin
UO1 UART/SIO ch. 1 data output pin
7
P02
S
General-purpose I/O port
Hysteresis/
analog
CMOS/
LCD ——
INT02 External interrupt input pin
AN02 8/12-bit A/D converter analog input pin
SEG35 LCDC SEG35 output pin
UCK2 UART/SIO ch. 2 clock I/O pin
8
P01
V
General-purpose I/O port
CMOS/
analog
CMOS/
LCD ——
INT01 External interrupt input pin
AN01 8/12-bit A/D converter analog input pin
SEG36 LCDC SEG36 output pin
UI2 UART/SIO ch. 2 data input pin

MB95710M Series
MB95770M Series
Document Number: 002-09307 Rev. *D Page 14 of 172
9
P00
W
General-purpose I/O port
Hysteresis/
analog
CMOS/
LCD ——
INT00 External interrupt input pin
AN00 8/12-bit A/D converter analog input pin
UO2 UART/SIO ch. 2 data output pin
10 P16 YGeneral-purpose I/O port Hysteresis CMOS ——
PPG10 8/16-bit PPG ch. 1 output pin
11 P15 YGeneral-purpose I/O port Hysteresis CMOS ——
PPG11 8/16-bit PPG ch. 1 output pin
12 P14 HGeneral-purpose I/O port Hysteresis CMOS —Ο
UCK0 UART/SIO ch. 0 clock I/O pin
13 P13 HGeneral-purpose I/O port Hysteresis CMOS —Ο
ADTG 8/12-bit A/D converter trigger input pin
14 P12 DGeneral-purpose I/O port Hysteresis CMOS Ο—
DBG DBG input pin
15 P11 HGeneral-purpose I/O port Hysteresis CMOS —Ο
UO0 UART/SIO ch. 0 data output pin
16 P10 GGeneral-purpose I/O port CMOS CMOS —Ο
UI0 UART/SIO ch. 0 data input pin
17 P53 HGeneral-purpose I/O port Hysteresis CMOS —Ο
TO0 16-bit reload timer ch. 0 output pin
18
P52
H
General-purpose I/O port
Hysteresis CMOS —ΟTI0 16-bit reload timer ch. 0 input pin
TO00 8/16-bit composite timer ch. 0 output pin
19
P51
H
General-purpose I/O port
Hysteresis CMOS —Ο
EC0 8/16-bit composite timer ch. 0 clock input
pin
20 P50 HGeneral-purpose I/O port Hysteresis CMOS —Ο
TO01 8/16-bit composite timer ch. 0 output pin
21 P23 IGeneral-purpose I/O port CMOS CMOS Ο—
SDA I2C bus interface ch. 0 data I/O pin
22 P22 IGeneral-purpose I/O port CMOS CMOS Ο—
SCL I2C bus interface ch. 0 clock I/O pin
23
P21
T
General-purpose I/O port
Hysteresis/
analog CMOS —Ο
PPG01 8/16-bit PPG ch. 0 output pin
CMP0_P Comparator ch. 0 non-inverting analog
input (positive input) pin
Pin no. Pin name I/O circuit
type*1Function I/O type
Input Output OD*2PU*3

MB95710M Series
MB95770M Series
Document Number: 002-09307 Rev. *D Page 15 of 172
24
P20
T
General-purpose I/O port
Hysteresis/
analog CMOS —Ο
PPG00 8/16-bit PPG ch. 0 output pin
CMP0_N Comparator ch. 0 inverting analog input
(negative input) pin
25
P90
R
General-purpose I/O port Hysteresis/
LCD power
supply
CMOS/
LCD
power
supply
——
V4 LCD drive power supply pin
26
P91
R
General-purpose I/O port Hysteresis/
LCD power
supply
CMOS/
LCD
power
supply
——
V3 LCD drive power supply pin
27
P92
R
General-purpose I/O port Hysteresis/
LCD power
supply
CMOS/
LCD
power
supply
——
V2 LCD drive power supply pin
28
P93
R
General-purpose I/O port Hysteresis/
LCD power
supply
CMOS/
LCD
power
supply
——
V1 LCD drive power supply pin
29
P94
R
General-purpose I/O port Hysteresis/
LCD power
supply
CMOS/
LCD
power
supply
——
V0 LCD drive power supply pin
30 PB2 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG37 LCDC SEG37 output pin
31 PB3 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG38 LCDC SEG38 output pin
32 PB4 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG39 LCDC SEG39 output pin
33 PA0 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
COM0 LCDC COM0 output pin
34 PA1 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
COM1 LCDC COM1 output pin
35 PA2 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
COM2 LCDC COM2 output pin
36 PA3 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
COM3 LCDC COM3 output pin
37 PA4 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
COM4 LCDC COM4 output pin
Pin no. Pin name I/O circuit
type*1Function I/O type
Input Output OD*2PU*3

MB95710M Series
MB95770M Series
Document Number: 002-09307 Rev. *D Page 16 of 172
38 PA5 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
COM5 LCDC COM5 output pin
39 PA6 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
COM6 LCDC COM6 output pin
40 PA7 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
COM7 LCDC COM7 output pin
41 VSS —Power supply pin (GND) ————
42 PF1 BGeneral-purpose I/O port Hysteresis CMOS ——
X1 Main clock I/O oscillation pin
43 PF0 BGeneral-purpose I/O port Hysteresis CMOS ——
X0 Main clock input oscillation pin
44 C —Decoupling capacitor connection pin ————
45 PG2 CGeneral-purpose I/O port Hysteresis CMOS —Ο
X1A Subclock I/O oscillation pin
46 PG1 CGeneral-purpose I/O port Hysteresis CMOS —Ο
X0A Subclock input oscillation pin
47 VCC —Power supply pin ————
48
PF2
A
General-purpose I/O port
Hysteresis CMOS Ο—
RST
Reset pin
Dedicated reset pin on
MB95F714M/F716M/F718M
49 P17 HGeneral-purpose I/O port Hysteresis CMOS —Ο
CMP0_O Comparator ch. 0 digital output pin
50 PB0 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG00 LCDC SEG00 output pin
51 PB1 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG01 LCDC SEG01 output pin
52 PC0 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG02 LCDC SEG02 output pin
53 PC1 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG03 LCDC SEG03 output pin
54 PC2 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG04 LCDC SEG04 output pin
55 PC3 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG05 LCDC SEG05 output pin
56 PC4 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG06 LCDC SEG06 output pin
Pin no. Pin name I/O circuit
type*1Function I/O type
Input Output OD*2PU*3

MB95710M Series
MB95770M Series
Document Number: 002-09307 Rev. *D Page 17 of 172
57 PC5 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG07 LCDC SEG07 output pin
58 PC6 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG08 LCDC SEG08 output pin
59 PC7 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG09 LCDC SEG09 output pin
60 P60 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG10 LCDC SEG10 output pin
61 P61 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG11 LCDC SEG11 output pin
62 P62 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG12 LCDC SEG12 output pin
63 P63 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG13 LCDC SEG13 output pin
64 P64 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG14 LCDC SEG14 output pin
65 P65 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG15 LCDC SEG15 output pin
66 P66 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG16 LCDC SEG16 output pin
67 P67 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG17 LCDC SEG17 output pin
68 P43 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG18 LCDC SEG18 output pin
69 P42 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG19 LCDC SEG19 output pin
70 P41 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG20 LCDC SEG20 output pin
71 P40 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG21 LCDC SEG21 output pin
72 PE0 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG22 LCDC SEG22 output pin
73 PE1 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG23 LCDC SEG23 output pin
74 PE2 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG24 LCDC SEG24 output pin
Pin no. Pin name I/O circuit
type*1Function I/O type
Input Output OD*2PU*3

MB95710M Series
MB95770M Series
Document Number: 002-09307 Rev. *D Page 18 of 172
Ο: Available
*1: For the I/O circuit types, see “I/O Circuit Type”.
*2: N-ch open drain
*3: Pull-up
75 PE3 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG25 LCDC SEG25 output pin
76 PE4 MGeneral-purpose I/O port Hysteresis CMOS/
LCD ——
SEG26 LCDC SEG26 output pin
77
PE5
M
General-purpose I/O port
Hysteresis CMOS/
LCD ——
SEG27 LCDC SEG27 output pin
TO11 8/16-bit composite timer ch. 1 output pin
78
PE6
M
General-purpose I/O port
Hysteresis CMOS/
LCD ——
SEG28 LCDC SEG28 output pin
TO10 8/16-bit composite timer ch. 1 output pin
79
PE7
M
General-purpose I/O port
Hysteresis CMOS/
LCD ——
SEG29 LCDC SEG27 output pin
EC1 8/16-bit composite timer ch. 1 clock input
pin
80 AVSS —Power supply pin (GND) for 8/12-bit A/D
converter and comparator ————
Pin no. Pin name I/O circuit
type*1Function I/O type
Input Output OD*2PU*3

MB95710M Series
MB95770M Series
Document Number: 002-09307 Rev. *D Page 19 of 172
6. Pin Functions (MB95770M Series)
Pin no. Pin name I/O circuit
type*1Function I/O type
Input Output OD*2PU*3
1AVCC —Power supply pin for 8/12-bit A/D
converter and comparator ————
2
P07
S
General-purpose I/O port
Hysteresis/
analog
CMOS/
LCD ——
INT07 External interrupt input pin
AN07 8/12-bit A/D converter analog input pin
SEG22 LCDC SEG22 output pin
3
P06
S
General-purpose I/O port
Hysteresis/
analog
CMOS/
LCD ——
INT06 External interrupt input pin
AN06 8/12-bit A/D converter analog input pin
SEG23 LCDC SEG23 output pin
4
P05
S
General-purpose I/O port
Hysteresis/
analog
CMOS/
LCD ——
INT05 External interrupt input pin
AN05 8/12-bit A/D converter analog input pin
SEG24 LCDC SEG24 output pin
UCK1 UART/SIO ch. 1 clock I/O pin
5
P04
V
General-purpose I/O port
CMOS/
analog
CMOS/
LCD ——
INT04 External interrupt input pin
AN04 8/12-bit A/D converter analog input pin
SEG25 LCDC SEG25 output pin
UI1 UART/SIO ch. 1 data input pin
6
P03
S
General-purpose I/O port
Hysteresis/
analog
CMOS/
LCD ——
INT03 External interrupt input pin
AN03 8/12-bit A/D converter analog input pin
SEG26 LCDC SEG26 output pin
UO1 UART/SIO ch. 1 data output pin
7
P02
S
General-purpose I/O port
Hysteresis/
analog
CMOS/
LCD ——
INT02 External interrupt input pin
AN02 8/12-bit A/D converter analog input pin
SEG27 LCDC SEG27 output pin
UCK2 UART/SIO ch. 2 clock I/O pin
8
P01
V
General-purpose I/O port
CMOS/
analog
CMOS/
LCD ——
INT01 External interrupt input pin
AN01 8/12-bit A/D converter analog input pin
SEG28 LCDC SEG28 output pin
TO00 8/16-bit composite timer ch. 0 output pin
UI2 UART/SIO ch. 2 data input pin