Cypress CY8CKIT-044 User manual

CY8CKIT-044 QUICK START GUIDE
PSOC®4 M-SERIES PIONEER KIT
Kit Contents:
1 PSoC®4 M-Series Pioneer board
2 USB Standard-A to Mini-B cable
3 Four jumper wires (4 inches each)
4 Two proximity sensor wires (5 inches each)
5 Micrium®μC/Probe®license card
6 Quick Start Guide (this document)

CY8CKIT-044 QUICK START GUIDE
• Bring your nger closer to the CapSense®Gesture
Pad to wakeup the system using proximity sensing.
The on-board RGB LED will turn on with white color
The RGB LED will turn off after 3 seconds if your
nger is taken away from the Gesture Pad
• Connect the board to your computer using the
provided USB cable
Note: This demo does not require driver installation,
although this may continue in the background
3
• Control the RGB LED's color and brightness using
the Gesture Pad
Note: Once your nger is removed from the Gesture
Pad, the PSoC 4200M device will switch to low-power
mode. On wakeup using proximity sensing, the RGB
LED will turn on with the last selected color
Supported gestures
RGB color change VIBGYOR color change Brightness control
21

CY8CKIT-044 QUICK START GUIDE
• Download and install the PSoC Creator IDE, PSoC 4 M-Series Pioneer Kit
code examples, documents and hardware design les from
www.cypress.com/CY8CKIT-044
Additional Learning Resources
PSoC CreatorTM: www.cypress.com/PSoCCreator
AN79953 – Getting Started with PSoC 4:
www.cypress.com/AN79953
AN73854 – PSoC 3, PSoC 4, and PSoC 5LP Introduction to Bootloaders:
www.cypress.com/AN73854
AN84858 – PSoC 4 and PSoC Analog Coprocessor Programming Using an
External Microcontroller (HSSP): www.cypress.com/AN84858
AN85951 – PSoC 4 and PSoC 6 MCU CapSense Design Guide:
www.cypress.com/AN85951
PSoC Code Examples: www.cypress.com/codeexamples
4

1 Power and Status LED
2 USB connector (J6)
3 System power supply jumper (J9) and
LDO (3.3V)
4 PSoC 5LP programmer and debugger
(CY8C5868LTI-LP039)
5 PSoC 5LP I/O header (J8)
6 PSoC 4200M (CY8C4247AZI-M485)
7 PSoC 4200M program and
debug header (J13)
8 Digilent®PmodTM compatible I/O
header (J16)
9 PSoC 4200M reset button
10 ArduinoTM compatible power header (J1)
11 RGB LED
12 User button
13 Arduino compatible I/O headers
(J2/J3/J4)
14 Header for Raspberry Pi (J15)
15 3-Axis Accelerometer
16 CapSense Proximity headers (J10/J11)
17 PSoC 4200M current measurement
jumper (J14)
18 CapSense Gesture Pad
19 PWM Temperature Sensor
20 Cypress F-RAM 1 Mb (FM24V10-G)
21 Ambient Light Sensor
22 32.768 kHz crystal
23 PSoC 5LP program and debug header (J5)
PSoC 4 M-Series Pioneer Board Details
CY8CKIT-044 QUICK START GUIDE
PSOC®4 M-SERIES PIONEER KIT
15
16
16
19
202122
13
3
23
1
2
4
5
6
7
8 9 10 11 12 13
14
17
18
For the latest information about this kit, visit www.cypress.com/CY8CKIT-044
© 2015 - 2018 Cypress Semiconductor Corporation. All rights reserved. PSoC and CapSense are registered
trademarks of Cypress Semiconductor Corporation. Raspberry Pi is a trademark of the Raspberry Pi Foundation.
All other trademarks or registered trademarks referenced herein are the property of their respective owners.
001-95920 Rev.*F
P3_7
P3_6
P4_0/SCL P4_1/SDA P1_7/AREF GND/GND P6_2/D13 P6_1/D12 P6_0/D11 P2_7/D10 P0_3/D9 P0_2/D8 P5_5/D7 P5_3/D6 P1_3/D5 P1_2/D4 P1_1/D3 P1_0/D2 P3_1/D1 P3_0/D0
VCC/VDD
GND/GND
SCK/P6_2
MISO/P6_1 MOSI/P6_0
SS/P6_4
P5LP3_0
P5LP12_7
P5LP3_7
P5LP3_5
P5LP0_1
P5LP1_2
VDD
P5LP0_0
P5LP3_4
P5LP3_6
P5LP12_6
P5LP12_1
P5LP12_0
P5LP2_5
GND
P5LP12_5
NC
IOREF/P4_VDD
RESET/RESET
3.3 V/V 3.3
5 V/V 5.0
GND/GND GND/GND
VIN/VIN
A0/P2_0 A1/P2_1 A2/P2_2 A3/P2_3 A4/P2_4 A5/P2_5
P0_0 P0_1 P0_7
P2_6
P6_5
P0_6
P4_4
P4_5
P4_6
GND
P3_4
P3_5
Arduino Uno R3
PSoC 4 M-Series Pioneer Kit
Digilent Pmod