D-Link DUB-E100 User manual

1
D-Link USB 2.0 Fast
Ethernet Adapter
DUB-E100DUB-E100
DUB-E100DUB-E100
DUB-E100
This product can be used with:This product can be used with:
This product can be used with:This product can be used with:
This product can be used with:
Windows XP, Me, 2000,Windows XP, Me, 2000,
Windows XP, Me, 2000,Windows XP, Me, 2000,
Windows XP, Me, 2000,
98 Second Edition98 Second Edition
98 Second Edition98 Second Edition
98 Second Edition
CheckYourPackageContents
These are the items included with your purchase:
If any of the below items are missing, please contact your reseller.
BeforeYouBegin
You must have at least the following:
•Windows XP/Me/2000/98 Second Edition
•One Available USB Port
•CD-ROM Drive
• DUB-E100 USB 2.0 Fast Ethernet Adapter
• Drivers on CD-ROM

2
Installing The DUB-E100
System Requirements
•Pentium Class PC 200Mhz or above
•16MB RAM
•One Available USB Port
•Microsoft Windows XP, 2000, Me, 98 Second Edition
Plug the “A” Connector of the
DUB-E100’s USB cable into an
available USB slot on your com-
puter.
Your computer should automatically detect the DUB-E100 and prompt you
to install the driver. Please proceed to the next section to complete the
driver installation.
Attach the other end of the
CAT5 Ethernet cable to a
switch, hub, or router/gate-
way.
Attach a CAT5 Ethernet
cable with an RJ-45 con-
nector to the RJ-45 jack of
the DUB-E100

3
Note: Windows Me Screens
will vary slightly from the
Windows XP screens shown.
Windows XP & Me Users
CompletingTheDriverInstallation
Click Next
Click Finish
Click Continue Anyway
Windows Me users may be asked to restart the computer. Select
“Yes” to restart your computer and complete the installation.

4
Windows 2000 Users
Click Next
Click Next
Click Next
Make sure to
check ONLY the
CD-ROM drives
box and uncheck
all other boxes.
Completing The Driver Installation

5
Click Next
Click Finish
Click Yes
Windows 2000 Users
You may be asked to restart your computer. Select Yes to restart your
computer and complete the installation.
Completing The Driver Installation

6
Windows 98SE Users
Click Next
Click Next
Click Next
Completing The Driver Installation

7
Windows 98SE Users
Click Next
Click Finish
Click Yes
Type in g:\win98 (use the
appropriate letter corre-
sponding to your CD-ROM
drive) then Click OK.
Click Next
Note: You may see these next 2
screens.
Completing The Driver Installation

8
The Installation is Complete!
You have now completed installation of the DUB-E100. Please check the
LED indicators on the DUB-E100 which will indicate proper installation.
The DUB-E100 features two LED indicators. The Link LED located on
the left of the Ethernet port indicates that there is an active connection
between the DUB-E100 and the network, and the Tx/Rx LED located on
the right of the Ethernet port indicates that data is being transferred.
•The Link LED is green when the DUB-E100 is operating at
100Mbps.
•The Link LED is amber when the DUB-E100 is operating at
10Mbps.
•The Tx/Rx (transmitting and receiving) LED flashes green when the
DUB-E100 is transmitting or receiving information.
If both LED’s are off, there is no connection. Check the network cables
and make sure that there is a physical connection between the DUB-
E100, your computer, and your network.
Tips
You can verify that the DUB-E100 is installed properly by using the follow-
ing steps.
•Right click on My Computer and select Properties.
•Click on the Hardware tab, and click on Device Manager.
•Click on the plus sign located to the left of Network Adapters to
expand the selection. D-Link USB DUB-E100 should appear,
indicating proper installation.
•If you have followed the instructions provided in this installation guide
and are still having trouble installing the DUB-E100, please refer to
the technical support information provided on the next page.

9
©2002 D-Link Systems, Inc. All rights reserved. Trademarks or registered trademarks are the property of
their respective holders. Software and specifications subject to change without notice. DUB-E100.030603
Technical Support
You can find software updates and user documentation on the D-Link website.
D-Link provides free technical support for customers within the United States and
within Canada for the duration of the warranty period on this product.
U.S. and Canadian customers can contact D-Link technical support through our
website, or by phone.
Tech Support for customers within the United States:
D-Link Technical Support over the Telephone:
[phone]
24 hours a day, seven days a week.
D-Link Technical Support over the Internet:
http://support.dlink.com
email:[email protected]
Tech Support for customers within Canada:
D-Link Technical Support over the Telephone:
[phone]
Monday to Friday 8:30am to 9:00pm EST
D-Link Technical Support over the Internet:
http://support.dlink.ca
email:[email protected]