D-Link PersonalAir DBT-120 User manual

2
Rev.2.0 (08/27/2002)
DBTDBT
DBTDBT
DBT
--
--
-120120
120120
120
Bluetooth USB Adapter

3
Contents
Introduction.....................................5
Package Contents..............................6
Installing Bluetooth Software ............6
Hardware Installation ........................8
Introduction to Bluetooth Software ....9
Bluetooth Software Basic Operations. 4
Client Applications .........................20
Local Services.................................29
Configuration Panel ........................3
Security .........................................52
Troubleshooting.............................. 56

4

5
Introduction
Introduction to BluetoothIntroduction to Bluetooth
Introduction to BluetoothIntroduction to Bluetooth
Introduction to Bluetooth
The term “Bluetooth” refers to a worldwide standard for the wireless
exchange of data between two devices within a short range. In order to
exchange data, two Bluetooth devices must establish a connection. Before
a connection is established, one device must request a connection with
another, where the second device accepts (or rejects) the connection. The
originator of the request is known as the client. The device that accepts (or
rejects) the request is known as the server. Many Bluetooth devices can act
as both client and server. A client Bluetooth device runs a software program
that requests a connection to another device as part of its normal operation.
For example, the program may request a connection to a remote computer,
a printer, or a modem.
Becoming a Bluetooth client normally requires an action by the device
operator, such as an attempt to browse a remote computer, print a file, or
dial out on a modem. Every Bluetooth device that provides a service must
be prepared to respond to a connection request. Bluetooth software is
always running in the background on the server, ready to respond to
connection requests.
Introduction to the D-Link Bluetooth USB AdapterIntroduction to the D-Link Bluetooth USB Adapter
Introduction to the D-Link Bluetooth USB AdapterIntroduction to the D-Link Bluetooth USB Adapter
Introduction to the D-Link Bluetooth USB Adapter
The D-Link Bluetooth USB Adapter is the best solution for quick and easy
access to Bluetooth enabled devices without cables or wires. It is a class 2/
3 low power device. The wireless transmission range of the D-Link Bluetooth
USB Adapter is about 15 Meter (45 feet). APC configured as the Bluetooth
server can support up to 7 Bluetooth client devices with IP addresses auto-
matically assigned whenthey connect.
After finishing the steps outlined in this manual, you will have the ability to
share information, obtain network access and take the full advantage of a
"connected" environment.

6
Package Contents
After opening the D-Link Bluetooth Adapter package, check what’s in the package,
then refer to the Installation Guide for the fastest way to get up and running with the
Bluetooth USB Adapter.
The following items should be found in the Bluetooth USB Adapter box:
•D-LinkDBT-120Bluetooth USBAdapter
•USB Extension Cable
•Installation CD with Manual & Software
•InstallationGuide
Installing Bluetooth Software
Uninstalling a previous version of Bluetooth software:Uninstalling a previous version of Bluetooth software:
Uninstalling a previous version of Bluetooth software:Uninstalling a previous version of Bluetooth software:
Uninstalling a previous version of Bluetooth software:
If you are installing the Bluetooth software for the first time, please skip this
section.
Any previous versions of the Bluetooth software must be uninstalled before installing
anupgradedversion.
Please uninstall the software by completing these steps:
1) Close any open programs and insert the Driver CD into your CD-ROM Drive.
2) The Autorun screen will appear. Click on Install Bluetooth Software.
3)The Welcome screen informs you the previous version of BTW you have
installed. Click on the Next button to continue.
4) Click on the Remove button from “Remove the Program” screen.
5) When the files have been removed, you will be presented with a screen
informing of its completion.
a.Click on the Finish button, a pop-up dialog box will show on the
screen.
b.Click on the Yes button to reboot your PC.
YouhavenowcompletelyuninstalledthepreviousversionoftheBluetoothsoftware.

7
Installing the Bluetooth software:Installing the Bluetooth software:
Installing the Bluetooth software:Installing the Bluetooth software:
Installing the Bluetooth software:
Be sure to install the Bluetooth software prior to plugging in the USB
Adapter to a USB port. If you have connected the Bluetooth adapter to your
computer, please remove it, cancel any hardware wizards that may show
up, restart your computer and start here.
1) Close any open programs and insert the Driver CD into your CD-ROM Drive.
2)The Autorun screen will appear. Click on Install Bluetooth Software.
3) The Welcome screen informs you that the WIDCOMM Bluetooth Software
Setup program is ready to begin. Click on the Next button.
4) In the License Agreement screen, click on the radio button to the left of I
accept the terms in the license agreement. Click on the Next button.
5) In the Device Information screen:
a. Enter a device name
b. Select a device type
c. Click on the Next button.
6) In the Destination Folder screen you are asked to confirm the Destination
Folder for the application software. If you would like, you may change the
destination folder to another location as the directory. Click on the Next button.
7) The Ready to Install the Program screen informs you that the driver is ready for
installation. Click on the Install button to continue.
Note: Please click on the OK button from the Driver Signature Notice dialog
box to proceed with driver installation in Windows 2000 and XP operating
systems.
8) When the files have been copied, you will be presented with a screen informing
of its completion.
a. Clickon theFinish button,apop-up dialog boxwillshow on thescreen.
b. Click the Yes button to reboot your PC.
9) After you reboot your PC, the Bluetooth Icon will reside in the Windows
system tray.

8
Hardware Installation
The Bluetooth USB Adapter is plug-&-play. After you have the software installed and
have rebooted your PC, you can plug the Bluetooth USB Adapter directly into your
laptop’s or desktop’s USB port. Or you can plug one end of the USB cable to your
computer and plug the Bluetooth USB Adapter to the other end of the USB cable.
When you plug the USB Adapter to the USB port, the green LED on the USB Adapter
should light up.
You may be prompted by a “Add New Hardware Wizard”, Click “Next” on each screen
with the driver CD in your CD-ROM drive to finalize the installation.
Note: The system will show a series of configuration messages in the Windows
system tray only when you have the software and hardware installed for the first
time. When you unplug and plug the USB Adapter subsequently, the system
won’t show the above bubble messages again.

9
Introduction to Bluetooth Software
The Bluetooth Software is the solution for the seamless integration of Bluetooth
technology into personal computers. The software provides an easy interface to
manage the Bluetooth Adapter.
Introduction to Bluetooth SoftwareIntroduction to Bluetooth Software
Introduction to Bluetooth SoftwareIntroduction to Bluetooth Software
Introduction to Bluetooth Software
Most Bluetooth-enabled devices have the capability to act as:
•A Bluetooth server—these devices provide one or more services, such as
access to the Internet, to other Bluetooth devices.
•A Bluetooth client—these devices use the service(s) provided by Bluetooth
servers.
Bluetooth devices that can act as both server and client can often do both at the
same time.
The Bluetooth software provides:
•Clients with the means:
oTo locate other Bluetooth devices in the immediate vicinity (inquiry)
oDiscover the services that those devices offer (discovery)
oConnect to, use, and disconnect from those services.
•Servers with the means to include/exclude individual services in the list of
services they provide to clients.
•Extensive security, including:
oAuthorization
oAuthentication
oEncryption

10
The services supported by Bluetooth Software are:
•Bluetooth Serial Port - establishes a Bluetooth wireless connection
between two devices. The connection may be used by applications as
though a physical serial cable connected the devices.
•Dial-up Networking - allows a Bluetooth client to use a modem that is
physically attached to the Bluetooth server.
•Fax - allows a Bluetooth client to wirelessly send a fax using a device that is
physically attached to the Bluetooth server.
•File Transfer - establishes a Bluetooth wireless connection that allows your
computer to perform file system operations on another Bluetooth-enabled
device—browse, drag/drop, open, print, cut/copy, paste, delete, rename,
etc.
•Information Exchange - establishes a Bluetooth wireless connection
between two devices so that they can exchange personal information
manager data such as business cards, calendar items, email messages,
and notes.
•Information Synchronization - establishes a Bluetooth wireless connection
between two devices and uses the connection to synchronize Personal
Information Manager data between the two devices.
•Network Access - establishes a Bluetooth wireless connection between the
client and a server that is physically connected to the Local Area Network. If
the client has permission (user name and password for the LAN), the
wireless connection can be used as if the client were hardwired to the LAN.
Note: All Bluetooth servers do not necessarily provide all of these services.
To determine the services provided by a Bluetooth device:
1. On the client, in the Folders panel of My Bluetooth Places, select Entire
Bluetooth Neighborhood.
2. In the right panel of Entire Bluetooth Neighborhood, right-click anywhere except
on a device name and select Refresh from the pop-up menu.
3. In the Folders panel of My Bluetooth Places, right-click a device and select
Discover Available Services from the pop-up menu to update the available
services list. The available services will be displayed in the right panel of My
Bluetooth Places.

11
Bluetooth Device IdentityBluetooth Device Identity
Bluetooth Device IdentityBluetooth Device Identity
Bluetooth Device Identity
Every Bluetooth device has an unique 48-bit binary Bluetooth Device Address (BDA)
burned into its EEPROM (embedded into the device). This address cannot be
changed by the end-user.
A device’s BDA is usually displayed in hexadecimal format; 00:D0:B7:03:2E:9F is a
valid BDA.
Each Bluetooth device also has an operator-configurable, user-friendly name to help
distinguish it from other Bluetooth devices. The user-friendly name may be up to 99
alphanumeric characters in length and may contain spaces. My Personal
Computer is a valid user-friendly name.
Icons Used For Bluetooth Devices and ServicesIcons Used For Bluetooth Devices and Services
Icons Used For Bluetooth Devices and ServicesIcons Used For Bluetooth Devices and Services
Icons Used For Bluetooth Devices and Services
Bluetooth icons provide at-a-glance feedback about a device or service’s status by
changing color.
•Device icons for Windows 98SE, 2K and ME.

12
•Device icons for Windows XP.
Service icons are gray or yellow in color (or gray with yellow accents) in their
“normal” state. In the “connected” state the primary color of the icon (gray or yellow)
changes to green.

13
•Service icons for Windows 98SE, 2K and ME.

14
•Service icons for Windows XP.
Services may be unavailable because they are in use or because the necessary
hardware (such as a modem for Dial-up Networking) is not installed.
Bluetooth Software Basic Operations
Find Bluetooth DevicesFind Bluetooth Devices
Find Bluetooth DevicesFind Bluetooth Devices
Find Bluetooth Devices
You can double click on the Bluetooth icon in the Windows system tray or
double click on the My Bluetooth Places on your desktop to launch
the My Bluetooth Places Explorer.

15
Bluetooth Software Explorer
Open the Bluetooth menu from the above screen and select Search for Devices.
The system will start to look for Bluetooth devices in the vicinity and display the
devices it finds in the right panel of My Bluetooth Places.
The Bluetooth Software can be configured to automatically search for devices on a
regular basis. From Configuration Panel/Discovery Tab, check the box of “Look for
other Bluetooth devices”. You can set a searching time so that the device will
search other Bluetooth devices at a regular time.
Note: If you find that some devices are within connection range but do not show up
in the list of devices found, the possible causes are:
•Your device is configured to report only specific types or classes of devices
•The unlisted device is configured to be non-discoverable

16
Find a ServiceFind a Service
Find a ServiceFind a Service
Find a Service
In the Folders panel of My Bluetooth Explorer, right-click on the device name and
select Discover Available Services from the pop-up menu. The services the device
provides will show up in the right panel.
In the Folders panel of My Bluetooth Explorer, right-click on the device name and
select Discover Available Services from the pop-up menu. The services the
device provides will show up in the right panel.
Bluetooth Software Explorer – Available Services
The services supported by Bluetooth software are:
•Bluetooth Serial Port - establishes a Bluetooth wireless connection between
two devices. The connection may be used by applications as though a physical
serial cable connected the devices.
•Dial-up Networking - allows a Bluetooth client to use a modem that is
physically attached to the Bluetooth server.
•Fax - allows a Bluetooth client to wirelessly send a fax using a device that is
physically attached to the Bluetooth server.
•File Transfer - establishes a Bluetooth wireless connection that allows your
computer to perform file system operations on another Bluetooth-enabled
device—browse, drag/drop, open, print, cut/copy, paste, delete, rename, etc.
•Information Exchange - establishes a Bluetooth wireless connection between
two devices so that they can exchange personal information manager (PIM) data
such as business cards, calendar items, email messages, and notes.

17
•Information Synchronization - establishes a Bluetooth wireless connection
between two devices and uses the connection to synchronize Personal
Information Manager data between the two devices.
•Network Access - establishes a Bluetooth wireless connection between the
client and a server that is physically connected to the Local Area Network. If the
client has permission (user name and password for the LAN), the wireless
connection can be used as if the client were hardwired to the LAN.
Note: All Bluetooth servers do not necessarily provide all of these services. For
example, network gateways only provide access to the Local Area Network (the
Network Access service).
Setup a ew ConnectionSetup a ew Connection
Setup a ew ConnectionSetup a ew Connection
Setup a ew Connection
Through the connection wizard, you can walk through the process of setting up a
new Bluetooth connection with another device. You can double click on the Add
Bluetooth Connection shortcut in the right panel of My Bluetooth Places or right-
click on the Bluetooth icon in the Windows system tray, select Services from the
pop-up menu, and then select Connection Wizard from the submenu.
Setup a new connectionSetup a new connection
Setup a new connectionSetup a new connection
Setup a new connection
1. On the first Connection Wizard screen:
a) In the Select a Service drop-down menu, select the type of connection that
will be established. (The specific service will be selected later, if necessary.)
b) In the “Select a device that provides the service” drop-down menu, select
the device that will provide the service. (To update the list of devices
displayed, click the Search Devices… button.)
c) Optional: select the “Require secure encrypted connection” option to
enable an Authentication and Encryption for this connection.
2. Click the Next button:
•If more than one service of the type selected in the Select a Service drop-
down menu (above) exists on the selected device, for example, multiple
Bluetooth Serial Ports, then the Select Bluetooth Service dialog box
appears. Select the specific service to be used, and then click the OK
button to close the Select Bluetooth Service dialog box.
•If only one service of the type selected in the Select a Service drop-down
menu (above) exists on the selected device, the next Connection Wizard
screenappears.
3. If “Require secure encrypted connection” was selected above, a security screen
mayappear:

18
•To establish a paired relationship with the remote device while using this
wizard, enter your Personal Identification Number in the PIN Code field of the
security screen, and then click the Next button.
•To establish the paired relationship with the remote device the first time this
connection is used, leave the PIN Code field blank in the security screen,
and click the Next button.
•Note: The Security screen WILL NOT appear if the devices have been
paired.
4. On the last Connection Wizard screen:
•The top of the screen provides basic information about the new connection—
the name of the device that will provide the service and the name of the
service that will be provided. If this information is NOT correct, click the
Back button to return to the previous screen, and from that screen select
the correct service and device.
•In the “Connection Name:” field, enter a descriptive name for the connection,
for example, “BT Serial Connection to Andy’s Desktop.”
Bluetooth TrayBluetooth Tray
Bluetooth TrayBluetooth Tray
Bluetooth Tray
The Bluetooth Tray icon resides in the Windows System Tray, which is
normally located in the lower-right corner of the screen. Bluetooth Tray provides fast
access to many routine Bluetooth operations.
From the Bluetooth Tray you can:
•Access My Bluetooth Places - double-click the Bluetooth icon.
•Access the Bluetooth Configuration Panel - right-click the Bluetooth
icon, select Setup, and then select Configuration from the submenu.
•Access the Bluetooth Security dialog box - right-click the Bluetooth
icon, select Setup, and then select Security from the submenu.
•Access the Bluetooth Connection Wizard - right-click the Bluetooth icon,
select Services, and then select Connection Wizard from the submenu.
•Exchange Business Cards with another Bluetooth Computer - right-
click the Bluetooth icon, select Services, and then select Business Card
Exchange from the submenu.
•Search for, and connect to, a specific service - right-click the Bluetooth
icon, select Services, and then select the desired service from the
submenu. An additional submenu will appear that contains one or more
options, including:
Find Devices…
or
Other Devices and one or more device names. The device name(s) will be
present if this computer has used this service, and connected via this
technique, at least once before. If a device name is present in the submenu,
selecting that device will re-initialize the connection.

19
The services that can be searched for and connected to from the Bluetooth Tray
are:
•Bluetooth Serial Port(s)
•Dial-upNetworking
•Fax
•FileTransfer
•InformationSynchronization
•Network Access.
Send to BluetoothSend to Bluetooth
Send to BluetoothSend to Bluetooth
Send to Bluetooth
This feature is used to send information to another Bluetooth device. Data types
include:
•Files from Microsoft Explorer
•Documents from Microsoft Office applications, including:
oWord
oExcel
oAccess
oPowerPoint.
•Contacts, appointments, tasks, messages, and notes from Microsoft
Outlook.
To use Send to BluetoothTo use Send to Bluetooth
To use Send to BluetoothTo use Send to Bluetooth
To use Send to Bluetooth
In the application:
•Microsoft Explorer - select one or more files to be transferred. Folders
cannotbetransferred.
•Microsoft Office - only the document in the active window can be
transferred.
•Microsoft Outlook -select one or more items to be transferred.
From Microsoft Explorer, go to the File menu, select Send To and then
select Bluetooth from the fly-out menu.
•Select Others to display the Select Device dialog box,
Or …
•Select a device from the sub-menu.
•Click the OK button to send the data. A dialog box displays progress.

20
Client Applications
etwork Accessetwork Access
etwork Accessetwork Access
etwork Access
The Network Access service permits a Bluetooth client to use a Local Area Network
connection that is physically attached to another Bluetooth device (the server).
Possible Network Access servers include:
•Bluetooth-enabled computers that have a hardwired Ethernet connection.
•Stand-alone Bluetooth Network Access Points.
The Bluetooth server must be specifically configured to provide the Network Access
service.
Note: After a Bluetooth device is configured as a Network Access server it cannot
act as a Network Access client until it has been re-configured to act as a Network
Access client.
Network ccess Server-side Setup for Windows2000Network ccess Server-side Setup for Windows2000
Network ccess Server-side Setup for Windows2000Network ccess Server-side Setup for Windows2000
Network ccess Server-side Setup for Windows2000
YoumustconfigureonecomputertoserveasaBluetoothserver,andthenotherBluetooth
client devices in the vicinity can access available services the server provides. Being a
Bluetooth Network Access server, the computer must have a hardwired Ethernet
connection and be specifically configured to provide the Network Access service.
•From the Windows Start menu scroll to Settings and select Control Panel.
On the Control Panel screen, double click on the Network and Dial-up
Connections.
•On the Network and Dial-up Connections screen, right-click on the Local
Area Connection icon, and select Properties from the pop-up menu.
•On the Local Area Connection Properties screen, click on the Sharing
tab; select Enable Internet Connection Sharing for this connection and
click on the OK button to close the screen.
Now, you have successfully configured your PC or laptop to the Bluetooth server so
Bluetooth client devices in the vicinity can link to the Bluetooth server.
Network ccess Server-side Setup for WindowsXP:Network ccess Server-side Setup for WindowsXP:
Network ccess Server-side Setup for WindowsXP:Network ccess Server-side Setup for WindowsXP:
Network ccess Server-side Setup for WindowsXP:
•From the Start menu scroll to Control Panel. In the Control Panel screen,
double click on the Network and Dial-up Connections icon.
•On the Network and Dial-up Connections screen, right-click on the Local
Area Connection icon, and select Properties from the pop-up menu.
•On the Local Area Connection Properties screen, click on the Advanced
tab; select Enable Internet Connection Sharing for this connection and
click on the OK button to close the screen.

21
Network ccess Server-side Setup for Windows 98SE & Windows ME:Network ccess Server-side Setup for Windows 98SE & Windows ME:
Network ccess Server-side Setup for Windows 98SE & Windows ME:Network ccess Server-side Setup for Windows 98SE & Windows ME:
Network ccess Server-side Setup for Windows 98SE & Windows ME:
If the Bluetooth sever is running in Windows 98SE or Windows ME, you have to install
anInternetProtocolRoutingsoftware.TherearelotsoftrialversionsofInternetProtocol
Routing software in the Internet. For example: A downloadable trial version of Sygate
Home Network is available on the Sygate Technologies Inc. website at http://www.
sygate.com/.
Installing and configuring the Sygate Home Network:
•Please follow the on-screen descriptions to install the Sygate Home Network.
Note: check the box of Server Mode on the Installation Setting dialog box
during installation.
•Click on the OK button from the Sygate Network Diagnostics screen.
•Click on the Yes button from the Reboot dialog box to restart your computer.
After you reboot your PC, click on the OK button from the Thank You For
Trying Sygate screen. The Sygate Manager screen will show up.
•Click on the Advanced button from the Sygate Manager screen and click on
the Configuration icon. The Configuration screen will show up.