D-Link DWL-P50 User manual

1
DWL-P50
Power Over
Ethernet Adapters
©2004 D-Link Systems, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective holders. Software
and specifications subject to change without notice.
About DWL-P50
Check Your Package Contents
DWL-P50 Power Over Ethernet Adapter
Female-to-Female Power Connector
Ethernet (CAT5 UTP/Straight Through) Cable
If any of the above items are missing, please contact your reseller.
The DWL-P50 Power Over Ethernet (POE) Adapters are designed to work with
D-Link PoE switches to deliver power over Ethernet to D-Link wireless Access
Point, IP Camera and IP phone, which didn’t support PoE. This allows you to place
those D-Link devices virtually anywhere in a building where power outlets are not
available. DWL-P50 Unit splits the data and DC power apart form D-Link PoE switch
and then supplies them to D-Link wireless Access Point, IP Camera and IP phone.
(Please refer appendix A for DWL-P50 compatibility with D-Link products )
Warning: Please follow the
instructions in this guide carefully.
Connecting these adapters
incorrectly may result in damage
to you network devices.

2
Connecting The DWL-P50
P+DATA IN:connect a CAT
5 RJ-45 straight- through
cable from PoE switch.
Use the Voltage Selector to set the DC output to 5V(11.5W) or 12V(12W)
depending upon your Network device’s power specifications.
Voltage Selector:used to
select DC 5V (11.5W) or
12V (12W)
LAN OUT:connect a CAT
5 RJ-45 straight- through
cable to an Ethernet
enabled device.
DC OUT:supplies 5V or
12V of power. Using the
included power cable,
connect to your Ethernet
enabled device’s power.

3
Use a CAT 5, 5e, or 6 UTP/STP straight-through Ethernet cable
Select voltage that your device requires before connect
power cable to power receptor. Incorrect voltage selection
may damage product.
Connecting The DWL-P50
Connect a Cat 5 Ethernet cable from the PoE port of switch (For example:
1~8 port of D-Link DES-1316) to the “P+DATA IN” of DWL-P50

4
Connect the provided Cat 5 Ethernet cable from DWL-P50 “LAN
OUT” to the RJ-45 LAN port of the Network Device.
Insert the Female-to-Female Power cable into “DC OUT” and the power
receptor of the Network Device. The Power LED of the Network Device
should light up.
Connecting The DWL-P50(continued)
Installation is complete! Your Network Device should have power and
data, and function normally.

5
Features
. IEEE 802.3af compatible.
. Optional output 5VDC or 12VDC.
. No Software Required and Operating System Independent.
. Work with D-Link PoE switches DES-1316 to provide Wireless AP, Internet
Camera, IP Phone or Equivalent 5VDC or 12VDC System.
Specifications
. Voltage
. Output: 5VDC or 12VDC
. Power Output
. Output: 11.5W(5VDC) or 12W(12VDC)
. Ethernet
. Connector: RJ-45
. Data Rate: 10/100Mbps
. Cable: TIA/EIA - 568, Category 5
. Dimensions
. 8.09 x 5.2 x 2.8cm
. Weight
. 80grams
. Temperature
. Operating: 0°C to 40°C (32°F to 104°F)
. Storage: -40°C to 70°C (-40°F to 158°F)
. Humidity
. Operation: 10%-80% RH
. Storage: 5% ~ 90% RH

Technical Support
You can find software updates and user documentation on the D-Link websites.
If you require product support, we encourage you to browse our FAQ section on
the Web Site before contacting the Support line. We have many FAQ’s which
we hope will provide you a speedy resolution for your problem.
For Customers within
The United Kingdom & Ireland:
D-Link UK & Ireland Technical Support over the Internet:
http://www.dlink.co.uk
ftp://ftp.dlink.co.uk
D-Link UK & Ireland Technical Support over the Telephone:
08456 12 0003 (United Kingdom)
[phone] (Ireland)
Lines Open
8.00am-10.00pm Mon-Fri
10.00am-7.00pm Sat & Sun
For Customers within Canada:
D-Link Canada Technical Support over the Telephone:
1-800-361-5265 (Canada)
Mon. to Fri. 7:30AM to 9:00PM EST
D-Link Canada Technical Support over the Internet:
http://support.dlink.ca
email: [email protected]