D-Link DI-604UP User manual

1. If you purchased this router to share your high-speed Internet connection with
other computers, you must have either an Ethernet-based Cable or a DSL modem
with an established Internet account from an Internet Service Provider (ISP).
2. It’s best to use the same computer that is connected to your modem for
configuring the DI-604UP router. The DI-604UP Broadband Router acts as a
DHCP server and will assign all the necessary IP address information on your
network. See Appendix at the end of this Quick Installation Guide or the
Manual on the CD-ROM for setting each network adapter to automatically
obtain an IP address.
Check Your Package Contents
These are the items included with your DI-604UP purchase:
If any of the above items are missing, please contact your reseller.
©2007 D-Link Networks, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective
holders. Software and specifications subject to change without notice.
This product can be set up using any
current web browser, i.e., Internet Explorer
6x, Netscape Navigator 7x.
• DI-604UP Broadband Router
• CD-ROM
• Ethernet (CAT5 UTP/Straight-Through) Cable
• 5V DC, 2 A Power Adapter
Using a power
supply with a
different voltage rating
will damage and void
the warranty for this
product.
Before You Begin
DI-604UP
Wired Router
with USB Printer Port

2
Connecting The DI-604UP Broadband
Router To Your Network
A. First, connect the power adapter to the receptor at the back panel of the DI-
604UP and then plug the other end of the power adapter to a wall outlet or power
strip. The Power LED will turn ON to indicate proper operation.
B. Insert one end of an Ethernet cable to the WAN port on the back panel of the
DI-604UP and the other end to the Ethernet port located on your Cable or DSL
modem. The WAN LED light will illuminate to indicate proper connection.
C. Insert one end of an Ethernet cable to LAN port 1 on the back panel of the DI-
604UP and the other end to an available Ethernet port on the network adapter in
the computer you will use to configure the DI-604UP. The LED light for LAN Port 1
will illuminate to indicate proper connection. (Note: Some computers already have
network adapters pre-installed.)
Restart Your Computer
B. WAN Port
This is the
connection for the
Ethernet Cable to
Ethernet Port on the
Cable or DSL
Modem.
Reset Button
Pressing this button
restores the router to its
original factory default
settings.
C.LAN Ports
These are the
connections for
Ethernet cables to
your Ethernet-
enabled com
p
uters
USB Port
This is connection for
your USB printer.
A
.Receptor for
Power Ada
p
ter

3
Connecting Additional Devices to the
DI-604UP Broadband Router
Using additional Ethernet (CAT5 UTP/Straight-Through) cables, connect your
Ethernet-equipped computer(s) to one of the 3 remaining Ethernet LAN ports on
the back panel of the DI-604UP.
Additional printer may be added to your DI-604UP to increase functionality. By
connecting a printer to the USB port at the back of the router, you may share print
capabilities over your wired network. A valid USB connection will cause the
corresponding USB LED at the front to light. For more information regarding USB
connections and device implementation, see the DI-604UP user guide.
LAN Port LEDs.
Each of the LAN ports on the back
of the DI-604UP have a
corresponding LED light on the front
panel of the unit. When a proper
connection has been made to a
computer that is ON, the LED on the
front panel should illuminate.
USB Port LED.
The USB port on the back of the
DI-604UP has a corresponding LED
light on the front panel of the unit.
When a proper connection has been
made to a device that is ON, the LED
on the front panel should illuminate.

4
When you have completed the steps in this Quick Installation Guide, your
connected network should look similar to this:
Cable or DSL
Modem
connected to
the WAN port.
DI-604UP
Broadband Router
Computers
connected
to the LAN
Ports
Printer
connected
to the USB
port.

5
Using The Setup Wizard
The logon pop-up screen will appear.
Once you have logged in, the Home screen will appear.
Open your Web
browser and type
“http://192.168.0.1” into
the URL address box.
Then press the Enter or
Return key.
Click OK
Type “admin” for
the username and
leave the password
field blank.

6
You will see the following screens.
Step 1 - Set up your new password.You have the option to establish a password.
Step 2 - Choose your time zone.
Click Run Wizard
Click Next
Click Next

7
The Setup Wizard (continued)
Select the type of Internet connection for your router.
If you selected Dynamic IP Address, this screen will appear:
Click Next
Click Next
If you are unsure of which setting to
select, please contact your Internet
Service Provider.
Select one of
these settings

8
If your ISP requires a Static IP Address, and this option is selected, then this screen
will appear:
If your ISP uses PPPoE (Point-to-Point Protocol over Ethernet) and this option is
selected, then this screen will appear:
What is a MAC address? Each
network adapter has a discrete
Media Access Control (MAC)
address. Note that some computers
and peripherals may already include
built-in network adapters.
Click Next
Click Next
Enter the IP address
information originally
provided to you by your
ISP. You will need to
complete all the required
fields.
“Clone MAC Address”
button to automatically
copy the MAC address
of the network adapter in
your computer. You can
also manually type in the
MAC address.

9
Click Next
Please be sure to remove any
existing PPPoE client software
installed on your computers.
Enter in the username
and password provided
to you by your ISP and
retype that same
password to verify it.

10
If your ISP uses PPTP and this option is selected, then this screen will appear.
If your ISP uses L2PT and this option is selected, then this screen will appear.
Enter the IP address
information originally
provided to you by your
ISP.
Click Next
Enter the IP address
information originally
provided to you by your
ISP.
Click Next