D-Link DSL-500 Installation manual

DSL-500 Console Commands Index and Syntax 1
(Suitable for Firmware R2.00 )
Commands are:
1. atm [<command>] -send command to atm process
2. bridge [<command>] -send command to bridge process
3. buffer [<command>] -send command to buffer process
4. bun [<command>] -send command to bun process
5. chips [<command>] -send command to chips process
6. config [<command>] -send command to config process
7. dhcpclient [<command>] -send command to dhcpclientprocess
8. dhcpserver [<command>] -send command to dhcpserver process
9. diap [<command>] -send command to diap process
10. dnsrelay [<command>] -send command todnsrelayprocess
11. edd [<command>] -send command to edd process
12. ethernet [<command>] -send command to ethernet process
13. event -control display of events
14. flashfs [<command>] -send command to flashfs process
15. ip [<command>] -send command to ip process
16. ip_filter [<command>] -send command toip_filter process
17. isfs [<command>] -send command to isfs process
18. itex [<command>] -send command toitexprocess
19. nat [<command>] -send command tonatprocess
20. oam [<command>] -send command to oam process
21. oamcli [<command>] -send command tooamcli process
22. portcli [<command>] -send command to portcli process
23. ppp [<command>] -send command toppp process
24. reflect [<command>] -send command to reflect process
25. restart -restart system
26. snmp [<command>] -send command to snmp process
27. tftp [<command>] -send command to tftp process
28. uptime -show time system has been running
29. version -show system software version
30. webserver [<command>] -send command to webserver process
DSL-500 Console Commands Index and Syntax

DSL-500 Console Commands Index and Syntax 2
1. atm
info -Get ATM driver information
pool -Get entry, size, prefix, count, name
2. bridge
config <command> -configuration commands
device command -Alter bridge configuration
ethertype [<port> "any"|"ip"|"pppoe"]
-Set or display forwarded packet types
filter -Display filtering database
filterage [age] -Set or display filter age time
flush [<port>] -Flush filtering database on port(s)
info -Show version
interface command -Process interface command
portfilter [<source port> "all"|<dest ports>]
-Set or display ports to forward to
spanning {command} -Control spanning tree operation
status -Display bridge status
version -Show version
3. buffer
list -list the buffer pools
info -[<name>] show [or set] current pool
show -[<n>] show buffer <n> in current pool, or all buffers in
use
steal -<n> steal <n> buffers from current pool, (0 to reset)
version -display version information for buffer pools
4. bun
BUN Commands -
help [command] -Display summary of commands

DSL-500 Console Commands Index and Syntax 3
version -Show softwareversion
build -Show build information
config <config_spec> -Enter manual configuration request
list config -Display all configuration requests
list devices -Display registered driver devices
list ports -Display registered ports
list channels <port_name> -Display enabled channels on a port
list all open channels <port_name> -Display all open channels on a port
list spices -Display all available spices
list objects -Display all data objects
show system -Show system attributes
set system -Set system attributes
show device <device_name> -Display device information
show port <port_name> -Display port information
show channel <port_name> <channel_number>
-Display channel information
set port <port_name> / <attribute> = <value> -Set port attribute
set channel <portname> <channelnumber> / <attribute> = <value>
-Set channel attribute
reset port <port_name> -Reset port hardware
list classes -List available port classes
show class <classname> -Show class members
5. chips
cpu -print percentage of cpu cycles used
debug -enter debug process
exit -abort from ATMos
info -print out version information and machine's address
mem -memory used on a process-by-process basis
stack -stack usage on a process-by-process basis
rb <addr> -read byte at address <addr>
rh <addr> -read halfword at address <addr>
rw <addr> -read word at address <addr>
tell <process> <string> -send string to process using TELL
message

DSL-500 Console Commands Index and Syntax 4
wb <addr> <val> -write byte <val> at address <addr>
wh <addr> <val> -write halfword <val> at address <addr>
ww <addr> <val> -write word <val> at address <addr>
6. config
list -List all modules registered
print [low | medium | high] [<module>] -Print configuration
reset [<module>] -Reset configuration to default
save -Save configuration
resource [<process> [<resource> [<value>]]] -Control resources
default -restore factory default settings
version -Display version information
7. dhcpclient
config -Displays client configuration file
help -Gives help on available commands
pool -Show DHCP client pool allocation stats
status -Shows status of active lease, or [all] leases
trace -Activates trace option(s)
untrace -Deactivates trace option(s)
version -Show software version
8. dhcpserver
config -Displays server configuration file
help -Gives help on available commands
pool -Show DHCP pool allocation statistics
status -Shows status of server leases
trace -Activates trace option(s)
untrace -Deactivates trace option(s)
version -Display software version

DSL-500 Console Commands Index and Syntax 5
9. diap
help -Gives help on available commands
enable -Enable DIAP Function
disable -Disable DIAP Function
passwd -Set DIAP Passwd-- passwd <password>|none
status -Show status of DIAP settings
trace -Activates trace option(s)
untrace -Deactivates trace option(s)
version -Show software version
10. dnsrelay
config -Show DNS relay configuration
help -List help on available commands
retry -Set max number of connection/tx retries
server -Manually specify DNS server IP address
status -Show DNS relay connection status
trace -Activate trace option(s)
untrace -Deactivate trace option(s)
version -Show DNS relay software version
state -enabled | disabled-Enable or Disable or Show state of
dnsrelay
pppauto -enabled | disabled-Enable or Disable or Show state of
pppauto
11. edd
event [level] -set event logging level
interface [id] command -process interface command for device id
status -device status
version -display driver information
12. ethernet
event [level] -set event logging level

DSL-500 Console Commands Index and Syntax 6
interface [id] command -process interface command for device id
status -device status
version -display driver information
13. event
event help -show this help
event n|next -show next part of event buffer
event p|previous -show previous part of event buffer
event r|recent -show most recent part of event buffer
event show -enable display of events as they occur
event unshow -disable display of events as they occur
14. flashfs
cat <file> -show file contents
config -display flash configuration
fsck -file system check, checks FLASH integrity
id <x> -display chip ID for device x
info -display file system information
ls [-l] -list FLASHFS files [more detail]
rewrite <file> -rewrite boot area with ISFS file <file>
trace [level] -show/set tracing level
update -commit ISFS files to FLASH
version -display version number
wipe -irreversibly erase FLASH contents
15. ip
arp syntax:
arp <cmd> -execute arp subcommand
arp help -list subcommands available
config syntax:
config [save] -display config or save to flash

DSL-500 Console Commands Index and Syntax 7
device syntax:
device [list] -list interface definitions
device add <i/f> <type> <file> [mtu <size>] [<IPaddr>|dhcp]
-create interface definition
device delete <i/f>
-remove interface definition
device flush -remove all interface definitions
disable syntax:
disable [<i/f>] -prevent use of interfaces or just interface <i/f>
enable syntax:
enable [<i/f> [mtu <size>] [<IPaddr>]]
-enable use of all interfaces or interface <i/f> if given
-set <i/f> IP address to <IPaddr>
-set MTU for interface
help syntax:
help -list commands available
help all -list commands and their syntax
help <command> -list syntax for command
ipatm syntax:
ipatm <cmd> -execute ipatm subcommand
ipatm help -list subcommands available
nat syntax:
nat add <i/f> -install NAT on interface
nat delete <i/f> -uninstall NAT from interface
norelay syntax:
norelay [all | <i/f name> [<i/f name>] [forward]]
-disallow relaying between i/fs
ping syntax:
ping <host> [<ttl> [<size>]]
-request echo from <host>

DSL-500 Console Commands Index and Syntax 8
relay syntax:
relay -list existing relays in place
relay all | <i/f name> [<i/f name>] [forward]
-allow relaying between i/fs
rip syntax:
rip <sub cmd> -execute rip subcommand
rip help -list subcommands available
route syntax:
route add <dom name> a.b.c.d <relay> [am:bm:cm:dm [<cost> [<timeout
s>]]]
-define/edit an IP forwarding route
route delete <dom name>
-delete a route
route flush -delete all routes
routes syntax:
routes -show IP forwarding routes
snmp syntax:
snmp <sub cmd> -execute snmp subcommand
snmp help -list subcommands available
stats syntax:
stats <sub cmd> -execute stats subcommand
stats help -list subcommands available
subnet syntax:
subnet add <net name> <i/f name> a.b.c.d am:bm:cm:dm
-create subnet definition
subnet delete <net name>
-remove subnet definition
subnet flush -remove all subnet definitions
version syntax:
version -display software version no.

DSL-500 Console Commands Index and Syntax 9
16. ip_filter
add help | <command> -set up rules for filter packets
delete help | <command> -delete set or rules for filter packets
flush help | <command> -flush all setting for filter packets
list help | <command> -list setting for filter packets
change help | <command> -change globe state on/off or
ifnotmatch pass/block
trace help | <command> -trun on/off ip filter
17. isfs
ls -list ISFS files
rm <file> -remove file from ISFS
cat <file> -show file contents
trace [level] -show/set tracing level
version -displays version number
18. itex
version -display version of itex implementation
line -Use up or down to activate/deactivate the line
rate -Get up/down stream rates
mode -Set mode [auto,ansi,dmt,lite]
info -Get info
txgain -Set/Get tx gain value
enhance -Set enhance mode
priority -Set priority(ansifirst or g.hs first)(0:ansi,1:g.hs)
alarm -Get Alarm indication
getes -Get error second
getsnr -Get snr
getrsd -Get RSD
channelmgr -Channel management
setcurve -Set curve
trellis -Set Trellis 1/0
bitswap -Set Bitswap 1/0

DSL-500 Console Commands Index and Syntax 10
dyinggasp -Send DyingGasp
vendorid -Set vendorid
test -test ITex135
delay -ANSI delay
list -List current configuration
minds -Set/Get Minimum DownStream value
19. nat
event [<level>] -show or change current event tracing level
interfaces -list interfaces
inbound help | <command> -set up rules for inbound packets
dmzip -show or set DMZ ip; Syntax: dmzip xxx.xxx.xxx.xxx
dmzstate enabled | disabled -Enable or Disable or Show status of
DMZ
info -show information about configured options
protocols -list protocols supported via ALGs
sessions <i/f name> [summary | all] -list active sessions
stats <i/f name> [reset] -show statistics
version -display ATMOS NAT version
20. oam
version -show version
config -show configuration
trace <util | fault | cc | loopback | all | none > -show / set tracing
dl -dump contents of lookup tables
21. oamcli
config -display message saying there is no storable configuration
version -show oamcli version
getversion -get the oam process version
inf -get a channels state
list -list channels state