D-Link DSL-504T User manual

1
ADSL Cable (ForAUS 200CM)
DSL
-
504T
ADSL Router
Ethernet Cable(CAT5UTP)
Power Adapter
Before You Begin
1. If you purchased this Router to share your high-speed Internet connection with
other computers, you musthavean establishedInternet accountfrom an
Internet Service Provider(ISP).
2. It s best to usethe same computer that is connected to your ISP forconfiguring
the DSL-504TADSL Router.The DSL-504Tacts as a DHCPserver and willassign
all the necessary IPaddress informationon yournetwork.See at the Quick
InstallationGuideor theManualon the CD-ROMfor setting eachnetwork adapter
to automatically obtainan IP address.
Check Your Package Contents
.
Thisproductcanbesetupusingany
currentwebbrowser,i.e.,Internet
Explorer6or NetscapeNavigator
6.2.3. DSL-
504T
ADSL Router
Usinga power adapter
with
a different voltage rating
willdamage andvoidthe
warranty forthis product.
CD
-
ROM
(containing User Manual)

2
Connecting the Router
1. Connect the power adapter
to the power input at the
back panel of the DSL-504T
then plug the other end of
the power adapter to a wall
outlet or power strip. Toggle
the power switch to the
powered on position. On the
front of the device, the Power
LED will light green to
indicate proper operation.
2. Insert one end of the
Ethernet cable into any
Ethernet port on the back
panel of the DSL-504T and
the other end of the cable to
an Ethernet Adapter or
available Ethernet port on
your computer.
3. Insert the telephone cable
included with the Router into
the ADSL port, then connect
the cable to your telephone
line. (Line must be activated
for ADSL use)
4. Check the LED display
on the front of the
Router to confirm that
the Ethernet connection
has been made. (Solid
light indicates a
connection for the
corresponding port)
ADSL port
- connect
to ADSL
line
Ethernet
ports -
connect to
Ethernet
cable
Fact
ory
Reset
button
Power
input -
connect
to power

3
Configure IP Settings
For Microsoft Windows XP
To connect to the network, make sure the network adapter in
your computer is configured properly. The following section
describes how to configure the network adapter to obtain an
IP address automatically for the DSL-504T ADSL Router.
Go to Start > select
Settings > click
Control Panel >
Double-click
on the
Network
Connections icon
Double
-
click
on
Network Connections
Right-click the
Local Area
Connection icon,
and then select
Properties.
Select Properties

4
Configure IP Settings cont
Click
Properties
The dialog box displays with
a list of currently installed
network items.
Click Internet Protocol
(TCP/IP)
Make the choice to get IP
settings assigned
automatically.
Select Obtain an IP
address automatically
Click
OK

5
Configuring the Router
To use your Web browser to access the web pages used to setup the
Router, your computer must be configured to “Obtain an IP address
automatically”, that is, you must change the IP network settings of
your computer so that it isa DHCP Client. If you are using Windows
XP and do not know how to change your network settings, refer to
Step 2. You may also read the User Manual for instructions on
changing IP settings for computers running Windows operating
systems.
The Login page appears
Openyour Web browser and
type http://10.1.1.1 into the
URL address box. Press Enter
or
Return.
When you first log in, your Login
Name is admin
; your password is
also admin. These may be
changed later.

6
Configuring the Router cont
Once you have logged in, the Home directory tab is
prominent with the setup Wizard menu displayed. Most users will be
able to use the setup wizard to establish the ADSL connection to your
ADSL Internet Service Provider (ISP). To begin usingthe setup wizard,
click on the Run Wizard button in the middle of the web page.
A pop-up menu will appear. This pop-up menu is the Setup Wizard.
The Setup Wizard procedure consists of four general steps:
1. Set your new password
2. Choose your time zone
3. Set Internet connection
4. Save & Restart
When you setup the Internet connection, you will need to enter the
information provided to you from yourISP. The type of information you
need depends on the type of connection you are setting up.
Click
the
Run Wizard
button.

7
Configuring the Router cont
The first Setup Wizard menu lists a summary of the steps required to
complete the setup. Click the Next button to begin setup.
Click
the
Next
button.

8
Configuring the Router cont
Set the new Password used by the administrator to configure the
Router. You have already used the default Password “admin”to access
the web manager. You can choose another Password. The login User
Name “admin”cannot be changed. Type in the new Password and type
it a second time to Verify Password. Click Next to continue.
Type thenew Password used by
the Router administrator and type
it again in Verify Password.
Click
the
Next
button.

9
Configuring the Router cont
Now configure the Time Zone used for the Router s system clock.
Select the appropriate time zone setting for your location.
Next you will Set the Internet Connection Type for the WAN
interface. Your ISP should have given this information to you. If you do
not know what type of connection to use, exit the Setup Wizard and
contact your ISP for the information. The Setup wizard menu that
appears when you click the Next button depends onwhat connection
type you select.
Select the Time Zone where you
are located.
Click
the
Next
button.

10
Configuringthe Router cont
PPPoE / PPPoA Connections
You will need to select either PPPoE or PPPoA for your connection
type in this menu. Type in the Username and Password used to
identify and verify your account to the ISP. Select the Connection
Type used for encapsulation on your ADSL service. Click Next to
continue. If you are not sure what Connection Type,please check
with your ISP.
Select the Connection
Type asinstructed by
your ISPaccount.
Click
the
Next
button.
Type the Username
and Password for
your ISPaccount.

11
Configuringthe Router cont
Setup Completed
All the settings for the connection are now completed. Click the
Restart button to save the new settings and restart the Router. It will
take about two minutes to restart the Router.
Do not turn off the Router while it’s restarting.
A message will appear informing you that “The device has rebooted
successfully”. You can now launch your web browser to access the
Internet.
Click
the
Restart
button.

12
Technical Support
You can findsoftware updates anduser documentation on
the D-Link website.
Tech Supportfor customers withinAustralia:
D-Link Technical Support over the Telephone:
1300-766-868
Mondayto Friday8:00am to 8:00pm EST
Saturday9:00am to 1:00pm EST
D-Link Technical Support over the Internet:
http://www.dlink.com.au
email:[email protected]om.au
Tech Supportfor customers withinNewZealand:
D-Link Technical Support over the Telephone:
0800-900-900
Mondayto Friday8:30am to 8:30pm
Saturday9:00am to 5:00pm
D-Link Technical Support over the Internet:
http://www.dlink.co.nz
email:[email protected]