D-Link DSL-G804V User manual

Check Your Package Contents
These are the items included with your purchase:
If any of the below items are missing, please contact your reseller.
©2005 D-Link System, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective
holders. Software and specifications subject to change without notice.
D
S
L-
G
804V Wireless AD
S
L Route
r
This product works with the following
operating system software: Windows
98, Windows NT, Windows 2000,
Windows Me and Windows XP.
DSL-G804V
Wireless ADSL Router
CD-ROM (Quick Install Guide and Manual)
One Ethernet (CAT5 UTP Straight-through)
Cable
One ADSL Cable
(standard telephone cable)
12V, 1A
Power Adapter
Using a power adapter
with different voltage
rating will damage and
void the warranty for this
product.
One Console (PS/2-RS232) Cable

2
Connecting the Router to your
Computer
Rear Panel Connections
Antenna
Omni Directional
ADSL Modem
Port
Connect to your
ADSL provider
Console Port
Connect to
PS2/RS-232
LAN Ports
Connects to the
LAN and other
computers
Factory Reset
Push in 5 seconds to
return to factory
default settings
DC Power Input
Connect to DC
Adapter
A、First, connect the power adapter to the power input at the back panel of the
DSL-G804V and then plug the other end of the power adapter to a wall outlet
or power strip.On the front of the device, the power LED will turrn ON to
indicate proper operation.
B、Insert one end of the Ethernet cable into an Ethernet(LAN) port on the back
panel of the DSL-G804V and the other end of the cable to an Ethernet Adapter
or available Ethernet port on your computer.
C、Insert the telephone cable included with the Router into the ADSL port, then
connect the cable to your telephone line.
D、Check the LED display on the front of the Router to confirm that the
connections have been made.

3
Connecting the Router to your
Computer (continued)
Front Panel LEDs
Power Steady green light indicates the unit is powered on. When the device
is powered off this remains dark.
Status
Lights steady green during power on self-test (POST). Once the
connection status has been settled, the light will blink green. If the
indicator lights steady green after the POST, the system has failed
and the device should be rebooted.
ADSL:
Link/Act
Steady green light indicates a valid ADSL connection. This will light
after the ADSL negotiation process has been settled. A blinking
green light indicates activity on the WAN (ADSL) interface.
WLAN Lit green when the wireless connection is established. A blinking
green when sending/receiving data.
LAN 1 - 4:
Link/Act
Green: The router has a successful 100Mb Ethernet connection. A
solid green light indicates a valid link on startup. These lights blink
when there is activity currently passing through the Ethernet port.
Orange: The router has a successful 10Mb Ethernet connection. A
solid green light indicates a valid link on startup. These lights blink
when there is activity currently passing through the Ethernet port.
PPP/MAIL Lit steady when there is a PPPoA / PPPoE connection. Lit and
flashed periodically when there is email in the Inbox

4
Configuring the Router
You have two methods to configure your router. The one is you can use the
Configuration Utility which is contained in the CD-ROM and follow the instructions
step by step to easy configure your router.
The other one is to use your Web browser to access the web pages used to setup the
Router, your computer must be configured to “Obtain an IP address automatically”,
that is, you must change the IP network settings of your computer so that it is a DHCP
Client. If you are using Windows XP and do not know how to change your network
settings, skip ahead to Appendix A and read the instructions provided. You may also
read the User Manual for instructions on changing IP settings for computers running
Windows operating systems.
Open the web browser and
type http://192.168.1.1 in
the browser’s address box.
This number is the default IP
address for this router.
Press Enter.
A user name and password
window will appear. The
default User Name and
Password are “admin” and
“admin”. Press OK to logon
to the router.
Click OK

5
Configuring the Router (continued)
Once you have logged in, the Home directory tab is prominent with the Setup Wizard
menu displayed. Most users will be able to use the Setup Wizard to establish the
ADSL connection to your ISP. To begin using the Setup Wizard, click on the Run
Wizard button in the middle of the web page. A pop-up menu will appear. This pop-up
menu is the Setup Wizard. The Setup Wizard procedure consists of four general
steps:
1. Set your new password
2. Set Internet connection
3. Set Wireless connection
4. Save configuration
When you setup the Internet connection, you will need to enter information provided by
your ISP. The type of information you need depends on the type of connection you are
setting up.
Click on the Run Wizard button.

6
Configuring the Router (continued)
The first window of the Setup Wizard menu lists a summary of the steps required to
complete the setup. Click the Next button to begin setup and go on to step 1.
Click the Next button.

7
Configuring the Router (continued)
The factory default password is admin, you may like change the the password by
entering in a new password.
Click the Next button.

8
Configuring the Router (continued)
You will see the Detecting Internet Connection Type Screen.
Next, you need to select and set the Internet Connection Type for the WAN
interfaces. Your ISP has given this information to you. If you do not know what type of
connection to use, exit the Set Wizard and contact your ISP for the information. The
Setup Wizard menu that appears when you click the next button depends on what
connection type you select.
Click the Next button.
Select the Connection Type used
for
y
our ADSL service.

9
Configuring the Router (continued)
PPPoE/PPPoA Connections
Type in the Username and Password used to identify and verify your account to the
ISP. The VPI number and VCI number should not be changed unless you have been
instructed by ISP to change them. Select the Connection Type used for
encapsulation specific to your service. Click Next when you are ready to continue to
the Setup Completed menu. If you are not sure what Connection Type,VPI and VCI
to use, please check with your ISP.
Click the Next button.
Type the VPI and
VCI, if these
values are not
correct, check
with your ISP for
information.
Type the
Username and
Password for
your ISP
account.
Use the pull-
down menu to
choose the
correct
Connection
Type. The user
may choose
between PPPoE
or PPPoA, as
instructed by
your ISP.
Type the IP addresses for the
WAN IP Address, Subnet
Mask, ISP Gateway
Address, Primary DNS
Address and/or Secondary
DNS Address, as instructed
by your ISP.

10
Configuring the Router (continued)
MPoA/IPoA
For this connection type, the user may choose MPoA or IPoA. The VPI number and
VCI number should not be changed unless you have been instructed by ISP to change
them. Select the Connection Type used for encapsulation specific to your service.
Click Next when you are ready to continue to the Setup Completed menu.If you are
not sure what Connection Type,VPI and VCI to use, please check with your ISP.
Click the Next button.
Use the pull-
down menu to
choose the
correct
Connection
Type. The user
may choose
between MPoA
or IPoA, as
instructed by
your ISP.
Type the VPI and
VCI, if these
values are not
correct, check
with your ISP for
information.
Type the IP addresses for the
WAN IP Address, Subnet
Mask, ISP Gateway
Address, Primary DNS
Address and/or Secondary
DNS Address, as instructed
by your ISP.