D-Link mydlink DCS-8600LH User manual

Full HD Outdoor
Wi-Fi Camera
Quick Start Guide
DCS-8600LH
Schnellinstallationsanleitung
Guide de démarrage rapide
Guía de inicio rápido
Guida di avvio rapida
Beknopte handleiding
Skrócona instrukcja obsługi
Stručná úvodní příručka
Gyors kezdési útmutató
Hurtigstartguide
Hurtig startvejledning
Pikaopas
Snabbstartsguide
Guia Iniciação Rápida
Οδηγός γρήγορης εκκίνησης
Vodič za brzi početak
Priročnik za hitro uporabo
Ghid de pornire rapidă

DCS-8600LH
2
ENGLISH
ENGLISH

3
DCS-8600LH
ENGLISH
1
Plug the included USB Power Adapter into the back of the camera.
Wait until the LED at the front changes from red to blinking orange.

DCS-8600LH
4
ENGLISH
2
To download and install the mydlink app on your mobile device,
scan the QR code above for your Android or iOS device.
Note: For best results and cloud recording use the new
mydlink app. This product is NOT COMPATIBLE with
mydlink Lite or mydlink+ apps.
If you are a mydlink Lite user, sign in to the new app
with the same username and password and your
existing cameras will appear in the new app.

5
DCS-8600LH
ENGLISH
3
New users: Tap Sign Up to register for a mydlink account, then tap
Add a Device to install your camera.
Existing users: Sign In using your mydlink account and tap the icon
at the top left, then tap Add a Device to start the setup wizard.
OR

DCS-8600LH
6
ENGLISH
4
When asked to scan the QR code, use the code found on the
bottom of the adapter. Repeat steps 1 through 4 to set up
additional cameras.
Note: The QR and pin code on the bottom of the adapter is
unique to the camera itself. Please be sure to scan each camera
individually during set up.
S/N:QXXXXYMXXXXXX
mydlink No.:XXXXXXXX
PIN Code:XXXXXX

7
DCS-8600LH
ENGLISH
Camera LED Information
Minimum Requirements
To install this product, you will need:
• 802.11n/g wireless router
• Internet connection
• A mobile device with Bluetooth 4.0 is required for setup.
• The latest version of the mydlink app from your operating
system’s application store.
• The mydlink app is available for iPhone, iPad and Android™
devices. Please refer to the mobile app's store page to check
whether your device is compatible.
• An e-mail account (required to register for mydlink service)
LED Indicative Color Status Description
Link/Act/Power
Green On Get IP Setup complete
Blinking Live streaming
Red On Power on Factory reset
Blinking F/W upgrading / Recovery
Orange On Bluetooth on
Blinking Bluetooth Setting

DCS-8600LH
8
ENGLISH
Outdoor Camera Mounting instructions
1. Place the baseplate at the desired location,
assuring that it is at least 20cm from the ceiling.
Make sure the screw is facing up and the holes
are level. Use a pencil to mark the holes.
2. Using a 6 mm drill bit, drill two 25 mm deep
holes over the pencil marks. For a plaster,
drywall, or concrete wall, insert the plastic
anchors to support the screws first.
3. Place the baseplate over the holes. Use the
supplied screws to attach the baseplate to the
wall.
4. Align the large top screw with the largest hole
on the snap mount. Slide the mount down to
lock into place.
5. Attach the back of the camera to the mount.
Adjust the angle as desired.
1
2
3
4
5
6
2
8
9
10
7
10

9
DCS-8600LH
ENGLISH
6. Place the baseplate at the desired location,
assuring that it is placed where close enough
for the cord to reach a power outlet. Make
sure the release tab facing up. Use a pencil to
mark the holes.
7. Using a 6 mm drill bit, drill two 25 mm deep
holes over the pencil marks. For a plaster,
drywall, or concrete wall, insert the plastic
anchors to support the screws first.
8. Place the baseplate over the holes. Use the
supplied screws to attach the baseplate to
the wall.
9. Align the power supply with the baseplate.
Press towards the wall to snap into place.
10. Connect the USB cable from the camera to
the power supply. Plug the power supply
into the power outlet.
Note: Both power cords can be used both
indoors and out.
1
2
3
4
5
6
2
8
9
10
7
10
Power Supply Mounting instructions

DCS-8600LH
10
DEUTSCH
ENGLISH