D-Link SECURICAM DCS-7110 User manual

This document will guide you through the basic installation
process for your new D-Link Network Camera.
DCS-7110
Documentation also available
on CD and via the D-Link
Website
Quick Installation Guide
Full HD Day & Night Network Camera
Quick Installation Guide
Installationsanleitung
Guide d’installation
Guía de instalación
Guida di Installazione

D-Link DCS-7110 Quick Install Guide
2
ENGLISH
DCS-7110 Quick Installation Guide
This installation guide provides basic instructions for installing the DCS-7110 Network
Camera on your network. For additional information about how to use the camera,
please see the User’s Manual which is available on the CD include in this package or
from the D-Link support website.
Installation Steps
1. Verify the package contents against the list below.
2. Hardware Overview
3. Hardware Installation
4. Conguration with Wizard
1. Package Contents
 DCS-7110 Network Camera
 Mounting Bracket
 User Manual and Software on CD-ROM
 CAT5 Ethernet Cable
 Power Adapter
 Screw
 Quick Installation Guide
If any of the above items are missing, please contact your reseller.

D-Link DCS-7110 Quick Install Guide
3
ENGLISH
2. Hardware Overview
Infrared LEDs
IR LEDs Illuminate the
camera's eld of view
DI/DO Connectors
DI/DO connectors provide a physical interface
to send and receive digital signals to and from a
variety of external devices
DC Power
Connects to the 12V DC power
adapter to power the camera
Ethernet (PoE)
RJ-45 connector is for Ethernet and can also
be used to power the camera using PoE
IR-Cut Removable (ICR) Sensor
IR-Cut Removable sensor judges
lighting conditions and switches
from day mode to night mode
accordingly
Sunshield
Adjustable
sunshield
protects the
camera sensor
from direct
sunlight
24V Power Connector
Connects to 24V AC power

D-Link DCS-7110 Quick Install Guide
4
ENGLISH
Reset Button
Removing the weatherproof cover,
use a paperclip or similar tool to press
and hold the recessed button for 10
seconds to reset the camera back to
the factory default settings
2. Hardware Overview

D-Link DCS-7110 Quick Install Guide
5
ENGLISH
3. Hardware Installation
Mounting the Camera
Step1: Using the two screws provided attach camera shoe to
the underside of the camera.
Step2: Using the bolt provided attach camera shoe to the
mounting bracket and adjust the vertical orientation of
the camera.
Step3: Using the Allen Wrench provided, loosen the bolts and
adjust the vertical / horizontal orientation of the camera
to desired eld of view. Firmly tighten the adjustment
bolts and lock it into the place.
Deploying the Camera
Step1: Locate an area on the wall which is capable of
supporting the weight of the camera.
Step2: Use a drill bit to make holes. Insert wall anchors
and afx the mounting bracket using the screws
provided.
Step3: The camera cables can be installed through a
separate large hole drilled in the wall, or using an
external cable conduit.

D-Link DCS-7110 Quick Install Guide
6
ENGLISH
Cable Connections
Basic Connection (without PoE)
1. Connect the camera to your switch or router via Ethernet cable.
2. Connect the power cable from the camera to the supplied power adapter.
3. Connect the supplied power adapter to a power outlet.
Connection Using a PoE Switch
If using a PoE switch or router, connect the network camera via Ethernet cable.
PoE will transmit both power and data over a single cable.
Note: Once power has been established, the LED will turn red. When the device has
obtained an IP address and is accessible, the LED will turn green.

D-Link DCS-7110 Quick Install Guide
7
ENGLISH
Note: To prevent the camera’s wire connectors from being damaged by water or other
elements:
1. When connecting the camera, the unsheathed part of the wire connectors must either
be sealed or enclosed in a junction box.
2. The unsheathed part of the wire connectors should be positioned at a downward-
facing angle when they extend out of the rear of the camera, not upward.
The unsheathed part of the wire connectors must either
be sealed or enclosed in a junction box.

D-Link DCS-7110 Quick Install Guide
8
ENGLISH
4. Conguration with Wizard
Insert the DCS-7110 CD into your computer's CD-ROM drive to begin the installation. If
the Autorun function on your computer is disabled, or if the D-Link Launcher fails to start
automatically, click Start > Run. Type D:\autorun.exe, where D: represents the drive
letter of your CD-ROM drive.
Click Setup Wizard to begin the installation.
After clicking Setuop Wizard, the following window will
open.
Click Next to continue.
Click Yes to accept the License Agreement.
Click Finish to complete the installation.
To start the installation process, click Next.
Note: The installation may take several minutes to
nish.

D-Link DCS-7110 Quick Install Guide
9
ENGLISH
Click on the D-Link Setup Wizard SE icon that was
created in your Windows Start menu.
Start > D-Link > Setup Wizard SE
Take a moment to conrm your settings and click Restart.
Select DHCP if your camera obtains an IP address
automatically when it boots up. Select static IP if the
camera will use the same IP address each time it is
started.
Click Next, to proceed to the next page.
Enter the Admin ID and password. When logging in for
the rst time, the default Admin ID is admin with the
password left blank.
Click Next, to proceed to the next page.
The Setup Wizard will appear and display the MAC
address and IP address of your camera(s). If you have
a DHCP server on your network, a valid IP Address
will be displayed. If your network does not use a
DHCP server, the network camera's default static IP
192.168.0.20 will be displayed.
Click the Wizard button to continue.

D-Link DCS-7110 Quick Install Guide
10
ENGLISH
Click on the D-Link Setup Wizard SE icon that was
created in your Windows Start menu.
Start > D-Link > Setup Wizard SE
Viewing Camera via Web Browser
This section shows your camera’s live video. You
can select your video prole and view or operate
the camera. For additional information about web
conguration, please refer to the user manual included
on the CD-ROM or the D-Link website.
Enter admin as the default username and leave the
password blank. Click OK to continue.
Select the camera and click the button labeled "Link"
to access the web conguration.
The Setup Wizard will automatically open your web
browser to the IP address of the camera.
TECHNICAL SUPPORT
United Kingdom (Mon-Fri) , Website: http://www.dlink.com
Home Wireless/Broadband 0871 873 3000 (9.00am–06.00pm, Sat 10.00am-02.00pm)
Managed, Smart, & Wireless Switches, or Firewalls 0871 873 0909 (09.00am- 05.30pm)
(BT 10ppm, other carriers may vary.)
Ireland (Mon-Fri), Website: http://www.dlink.com
All Products 1890 886 899 (09.00am-06.00pm, Sat 10.00am-02.00pm)
Phone rates: €0.05ppm peak, €0.045ppm off peak times