D-Link DES-7210-BASE User manual

This document will guide you through the basic installation
process for your new D-Link chassis-based switch.
Building Networks for People
DES-7200
Documentation also available on
CD and via the D-Link Website
Quick Installation Guide
6/10 Slot Chassis-Based Switch

2D-Link 6/10 Slot Chassis-Based Switch
About This Guide
This guide contains step-by-step instructions
for setting up the D-Link DES-7200 Series
Switch Chassis. Please note that the model
you have purchased may appear slightly
different from those shown in the illustrations.
Please read this manual carefully before using
the product, paying special attention to safety
warnings so as to avoid injury or damage to
equipment.
This manual is intended for users who have
experience in installing and maintaining
network hardware, and assumes that users are
familiar with standard networking terms and
concepts.
Product Overview
D-Link’s DES-7200 series of chassis-based
switches are intelligent and high-performance
multi-layer LAN devices designed for enter-
prise campus and metropolitan area networks
(MAN). They are ideal for deployment in
environments where uninterrupted network
applications and a high level of performance,
security and control are required.
(GCVWTKPICƀGZKDNGOQFWNCTCTEJKVGEVWTGCPFindustry standard compliance, these switches
provide scalable expansion and a high level
of investment protection for businesses
and telecom carriers to deploy Gigabit and
10-Gigabit packet switching and routing for
QHſEGPGVYQTMKPICPF'VJGTPGVDCUGF+PVGTPGVservices to homes.
Power Supply Safety Warning
Ground the device before powering-
on to guard against power surges.
Be sure that all cables are-
grounded correctly.
Static Electricity Protection
Warning
Always wear an anti-static wrist-
strap when contacting the chassis
to prevent static damage.
Laser Safety Warning
CLASS 1 LASER PRODUCT
Directly looking at the optical- KPVGTHCEGQTQRVKECNſDGTUOC[ECWUGeye damage.
Serial Interface Safety Warning
Hot plugging a cable into the serial-
interface may damage the terminal.
Please power off the chassis before
connecting or disconnecting cables
to/from the serial interface.
Fan Safety Warning
The fan mechanism is dangerous.-
Avoid touching the area near the
fan.
Transportation Safety Warning
The device and components may-
comprise more than 80kg in total.
Do not use the handles on the rear-
of the device to carry the chassis.
Use care when inserting or-
removing heavy components.
Maintenance Warning
Maintenance should only be carried- QWVD[SWCNKſGFUGTXKEGVGEJPKEKCPUWarnings

6/10 Slot Chassis-Based Switch 3
Moving the Device
The DES-7200 is large and heavy. When
handling, please pay close attention to the
following guidelines:
Avoid moving the equipment frequently.-
At least two people are needed to move-
the equipment. Do not attempt to move the
equipment alone.
Turn off all power supplies and unplug all-
power cables before moving the equipment.
Use the side handles to remove all line cards,-
the fan tray, and the power module from the
chassis before moving.
Figure 1. Correctly Moving the DES-7200
WARNING:
Do not move the equipment by
grasping the panel, power supply
handle, or ventilation holes, as they
are not designed to bear weight.
Preparation For Installation
To ensure normal operation and prolonged
life of the DES-7200, the appropriate temper-
ature and humidity must be maintained in the
equipment room.
+HVJGGSWKROGPVTQQOJCUVGORGTCVWTGCPFhumidity that do not meet the requirements, the
equipment may sustain damage.
Temperature Relative Humidity
Long-term
Condition
Short-
term
Condition
Long-term
Condition
Short-
term
Condition
0°C-45°C 0°C-45°C 40%-65% 10%-90%
To prevent damage from static electricity,
please conform to the following guidelines:
Be sure to a adequately ground all1.
electronic equipment.
Use appropriate dust prevention measures.2.
Maintain the required humidity in the3.
operating environment.
Always wear an anti-static wrist strap when4.
working around any electronic circuitry.
Hold a circuit board by its edges. Do not5.
touch any components on the PCB.
Do not allow clothing to touch a circuit6.
board. An antistatic wrist strap can only
prevent static electricity from the human
body, but cannot mitigate static electricity
from clothing.
Static Discharge Damage Prevention
Table 1. Temperature and Humidity Requirements
Note:
The ambient temperature and1.
humidity should be measured
at the point that is 1.5m above
VJGƀQQTCPFODGHQTGVJGequipment when there is no
protective plate in front or back of
the equipment rack.
The short-term working condi-2.
tions apply where the continuous
working period does not exceed
48 hours and the cumulative total
period within a year does not
exceed 15 days.
System Grounding Requirements
Proper grounding will help to ensure stable and
reliable operation of the DES-7200. Be sure
to verify that the grounding conditions at the
installation meet the grounding requirements,
and ground all devices appropriately.
Figure 2. Grounding of the DES-7200

4D-Link 6/10 Slot Chassis-Based Switch
Power Requirements
When DES-7200 uses the AC power supply:
7200-1200AC
Rated voltage: 100-240VAC, 50/60Hz
Tolerance range: 90-264VAC, 47-63Hz
Total power: 1200W
7200-2000AC
Rated voltage: 100-240VAC, 50/60Hz
Tolerance range:
90-176VAC, 47-53Hz 1200W
176-264VAC, 57-63Hz 2000W
Total power: 2000W
When DES-7200 uses the DC power supply:
7200-1200DC
Rated voltage: -48VDC
Tolerance range:8&%Ŧ8&%Total Power: 1200W
7200-2000DC
Rated voltage: -48VDC
Tolerance range:8&%Ŧ8&%Total Power: 2000W
DES-7200 Series
Modules
Maximum Power
Consumption (W)
7200-CM1 30
7200-CM2 30
7200-CM3 50
7200-CM4 50
7200-24G 75
7200-24 85
7200-48 100
7200-24GE 75
7200-2XG 75
7200-4XG 100
7200-24P
85+15.4*N
(N indicates the PoE port being
used, of which the value is less
than 24)
7200-48P
100+15.4*N
(N indicates the PoE port being
used, of which the value is less
than 48)
7200-ASE3 100
Table 2. Power Requirements
Note:
All grounding conductors should
be connected before, and discon-
nected after the line and neutral(AC)/
input(DC) conductors.
A minimum of 10mm² (6AWG) of-
conductive grounding should be
provided to the equipment grounding
terminals on the rear panel.
For power supply unit 7200-2000DC,-
a minimum 10mm² (6AWG) of
conductive grounding should be
provided to the input terminal.
For power supply unit 7200-1200DC,-
a minimum 4mm² (10AWG) of
conductive grounding should be
provided to the input terminal.
For power supply unit 7200-2000AC-
and 7200-1200AC, a minimum
2.5mm² (12AWG) of conductive
grounding should be provided to the
input terminal. Note:
The DES-7200 provides 1+1
power supply redundancy. D-Link
recommends the use of multiple
power supplies for the equipment
to ensure continuous and stable
operation. Redundant power helps to
prevent unexpected equipment power
failures. Redundant power supplies
must be identical.

6/10 Slot Chassis-Based Switch 5
Requirements of Installation Tools
Type Tools Remarks
Common
Tools
Claw hammer,
pliers
Unpack wooden
case and transpor-
tation case.
Phillips-head
screwdriver,
straight screw-
driver, spanner
Disassemble
chassis, power
supply, fan and
modules.
Power supply
cables, network
cables, optical
ſDGTUCPFFKUVTK-
bution cables
Connect the inter-
faces.
Ruler, long
tapeline, marker
pen
Measure the instal-
lation position.
Bolts, diagonal
pliers, straps Mount the chassis.
Special-
purpose
Tools
Anti-static tool Prevent static
electricity.
Wire stripper,
crimping pliers
Create network
cables and
grounding cables.
Meter
Multimeter Test power supply
and DC resistance.
500V megohm-
meter
Test the insulation
resistance and
grounding resis-
tance.
Requirements for Rack Mounting
The DES-7200 must be used indoors. To
ensure the normal operation and prolonged
WUGHWNſNGQHVJGGSWKROGPVVJGKPUVCNNCVKQPUKVGmust meet the following requirements.
+H[QWRNCPVQOQWPVVJG&'5KPCHTCOGplease observe the following guidelines:
+PUVCNNVJGUYKVEJKPCPQRGPECDKPGVKH-RQUUKDNG+H[QWKPUVCNNVJGUYKVEJKPUKFGa closed cabinet, please ensure that the
cabinet has a good ventilation and heat
dissipation system.
Ensure that the cabinet is durable enough-
to bear the weight of the DES-7200 and its
installation accessories. (QNNQYKPIſIWTGUJQYUVJGXGPVKNCVKQPrequirements of the DES-7200. You must
TGUGTXGUWHſEKGPVURCEKPIPGCTVJGXGPVUVQensure proper ventilation. After the cables
have been connected, they should be arranged
into bundles or placed on the cabling rack, to
prevent the obstruction of air inlets and vents.
With a person on each side of the1.
DES-7200, lift the chassis while keeping
it level. Slowly move it to the front of the
frame.
Keeping the DES-7200 level, lift it to a2.
position slightly higher than the tray or the
slide rail of the cabinet. Set the chassis onto
the tray or the slide rail, and push it into the
cabinet.
Fasten the DES-7200 to the cabinet with3.
screws. Fastening notches are on both the
left and right side of the front panel on the
equipment frame. Use screws to fasten
them to the bracket of the cabinet. Once
fastened, the equipment should be stable
and immobile.
Table 3. Required Tools
Installation Site Requirements
Ventilation Requirements
Mounting the DES-7200 into the Cabinet
Ensure that the dimensions of the cabinet-
provide enough space for the installation of
the front, rear, left and right panels of the
DES-7200 for the sake of heat dissipation.
The frame should be properly grounded.-
Figure 3. Ventilation of the DES-7200

6D-Link 6/10 Slot Chassis-Based Switch
The DES-7200 provides a ventilation system,
7210-FAN for DES-7210, and 7206-FAN for
DES-7206. Carry out the following steps to install
the fan tray:
Remove the blank panel of the fan tray1.
by loosening the captive screws with a
screwdriver.
Push the fan into the cabinet along the guide2.
rail.
Tighten the captive screws with a screwdriver.3.
Figure 4 shows the installed fan tray.
Figure 4. Installing the Fan Tray of the DES-7200
The DES-7200 system offers AC and DC power
options, which can be installed in the same way
by performing the following steps:
Remove one of the two blank panels from the1.
power module by loosening the two screws
with a Phillips-head screwdriver, as shown in
Figure 5.
Figure 5. Installing the Power Supply
of the DES-7210 and DES-7206 +PUGTVVJGRQYGTUWRRN[OQFWNGKPVQVJGcabinet along the guide rail, as shown in
Figure 6.
Figure 6. Installing the Power Supply
of the DES-7210 and DES-7206
3. Tighten the screws on both sides of the
power supply by using a screwdriver, as
shown in Figure 7.
Figure 7. Installing the Power Supply
of the DES-7210 and DES-7206
Installing the Fan Tray
Installing the Power Supply

6/10 Slot Chassis-Based Switch 7
To ease handling of the system, the DES-7200
chassis is provided with a handle, which can be
installed by carrying out the following steps:
Align the handle with the sunk hole on the1.
fastening bar.
Tighten the M4 sunk crosshead screws2.
provided with the unit, as shown in Figure 8.
Figure 8. Installing the Handle of the
DES-7210 and DES-7206
The cabling rack of the DES-7210 can be install
by carrying out the following steps:
Remove the blank panel of the tracing rack by1.
loosing the captive screws with a screwdriver
and the crosshead screws with a Phillips-head
screwdriver.
+PUVCNNVJGRCPGNQHVJGVTCEKPITCEMD[2.
tightening the two captive screws with a
screwdriver and the four crosshead screws
with a Phillips-head screwdriver.
Fasten the cabling rack with the crosshead M33.
screws provided. (The cabling rack is available
in two sizes. Please select the appropriate
model.) 5KORN[UNKFGVJGCKTſNVGTQHVJG&'5KPVQthe cabinet along the guide rail.
Figure 10. Installing the Air Filter of the DES-7210
Note:
#KTſNVGTKPUVCNNCVKQPKUTGEQOOGPFGFas the last step of chassis installation.
A working ground GND and a protection
ground PGND are installed on the back of
DES-7200. GND should be directly connected
VQVJGITQWPFDCTQHVJGGSWKROGPVTQQO+HCdigital grounding bar and an analog grounding
bar exist in the equipment room, the GND
should be connected to the digital bar.
PGND should be connected to a grounding
terminal on the cabinet. The grounding terminal
should then be connected to the grounding bar
QHVJGGSWKROGPVTQQO+HCFKIKVCNITQWPFKPIbar and an analog grounding bar exist in
the equipment room, the PGND should be
connected to the analog bar.
Figure 9b. Installing the Cabling Rack
of the DES-7210
Figure 9a. Installing the Cabling Rack
of the DES-7210
Installing the Handle
Installing the Cabling Rack of the DES-7210
Installing the Air Filter of the DES-7210
Connecting the System Ground

8D-Link 6/10 Slot Chassis-Based Switch
Connect the DC power cable according to the
label on the panel of the DC power module and
the wiring shown in the following diagram.
Precautions
Before connecting the power supply, you-
must verify that the external power supply
provided matches the power module installed
of this equipment.
Before connecting the power cable, you must-
ensure that the switch of the power module is
at the OFF position.
The power cables of various colors must be-
connected to the appropriate wiring posts.
You must ensure that the power cables-
connected are in good contact.
Simple Connection Steps
Remove the protection cover of the DC wiring
terminal.
Lock the power cable to the appropriate1. VGTOKPCNCEEQTFKPIVQVJGKFGPVKſECVKQPCPFtighten the pressing screw.
Put on the protection cover and tighten the2.
screw.
Connect the other end of the power cable to3.
the corresponding socket or connector.
Connect the related AC power cable according
VQVJG+&QPVJGRCPGNQHVJG#%RQYGTOQFWNGand the location requirement, as shown in the
following diagram.
Figure 11. Connection of Grounding Posts
on the DES-7200 back
Precautions
The sectional area of the grounding-
cable should be selected according to the
maximum possible current. Use insulated
cables of good conductivity.
Do not use bare wire.-
The grounding resistance for combined- ITQWPFKPIUJQWNFDGNGUUVJCPšSimple Grounding Steps
Release the nut on the rear grounding post1.
of the equipment.
#HſZVJGVGTOKPCNQHVJGITQWPFKPIECDNGVQ2.
the grounding pole.
Tighten the nut.3.
Connect the related terminals according to4.
the above steps and the wiring diagram.
Figure 12. Schematic Diagram for the Connection
of the DC Power Cable
Figure 13. Schematic Diagram for the Connection of
the AC Power Cable
Connecting the DC Power Supply to the
Power Module
Connecting the AC Power Supply to the
Power Module

6/10 Slot Chassis-Based Switch 9
Precautions
Before connecting the power supply, you-
must verify that the external power supply
provided matches the power module installed
in this equipment.
Before connecting the power cable, you must-
ensure that the switch of the power module is
in the OFF position.
Use only a power cable with a standard 3-pin-
connector.
You must ensure that the power cables are-
securely connected.
Simple Connection Steps
+PUGTVVJGRNWIQHVJGRQYGTECDNGKPVQVJG1.
power module.
Connect the other end of the power cable to2.
the corresponding socket or connector.
Connect the cable with the RJ-45 connector
to the Ethernet port of the equipment
management module, and the other end to the
Network Management or control terminal.
Connect the end of the standard DB-9 serial
cable with the RS-232 serial port to the RS-232
serial port of the equipment management
module, and connect the other end to the NM
or control terminal.
Remove the appropriate component card1.
or blank panel blank panel according to
UGEVKQPQHVJG*CTFYCTG+PUVCNNCVKQPGuide.
Replace it with the appropriate card and2.
insert into the guide rail.
Push the card into position by using the3.
ejector, and tighten the two captive screws
on the card with a screwdriver.
Warning:
Always wear an anti-static wrist strap before1.
plugging in or unplugging a board.
&QPQVJQNFVJGIQNFſPIGTQHVJG2%$QT2.
collide the components on the PCB.
Figure 14. Components
Connecting the Cable of the Management
Module
Removing Boards from the DES-7200
7PRNWICNNECDNGUſDGTUUWEJCUQRVKECN1. ſDGTUCPF4,VYKUVGFRCKTUHTQOVJGpanel.
Loosen two captive screws on the panel.2.
Remove the board by holding the ejector3.
with both hands.
Installing Boards on the DES-7200
Note:
The DES-7200 system must have
at least one management module to
work normally.
Warning:
&QPQVJQNFVJGIQNFſPIGTQHVJG1.
PCB or collide the components
on the PCB.
When you plug/unplug a PCB2.
module, use the ejector, instead
of forcedly.

10 D-Link 6/10 Slot Chassis-Based Switch
Consult the following list to determine if the
appropriate items have been included and are
in an acceptable condition.
1. DES-7200 Chassis Carton
Verify that the individual panels have been-
installed and adjusted properly.
Wheels-
Screws-
Documentation-
Packing List-
2. Module Carton
Contains the modules, packing list and-
documentation for the DES-7200.
This system may be managed out-of-band
through the console port on the Control
Module or in-band using Telnet. Each Switch
OWUVDGCUUKIPGFKVUQYP+2#FFTGUUYJKEJis used for communication with an SNMP
PGVYQTMOCPCIGTQTQVJGT6%2+2CRRNKECVKQP(for example BOOTP, TFTP). The Switch's
FGHCWNV+2CFFTGUUKU6JGWUGTECPEJCPIGVJGFGHCWNV5YKVEJ+2CFFTGUUVQOGGVVJGURGEKſECVKQPUQH[QWTPGVYQTMKPICFFTGUUscheme.
The switch provides an RJ-45 console port
that enables a connection to a computer or
VGTOKPCNHQTOQPKVQTKPICPFEQPſIWTCVKQP6Quse the console port, you need the following
equipment:
A terminal or a computer with both a serial-
port and the ability to emulate a terminal.
A null modem or crossover RS-232 cable-
with a female DB-9 connector for the console
port on the Switch.
Verify that the external power supply matches-
the distribution panel of the cabinet.
After the equipment is installed, check that-
the front/back cabinet doors can be closed.
Verify that the cabinet has been fastened-
completely, and does not move or tilt.
Verify that the equipment has been installed-
in the cabinet, and all the cables have been
fastened to the cabinet.
8GTKH[VJCVVJGQRVKECNſDGTCPFVYKUVGFRCKT-
cables match their respective interfaces.
Verify that the cables have been bound-
appropriately.
Verify that the power cables are in good-
condition and comply with safety require-
ments.
Verify that the power module has been-
correctly fastened using the two screws on
the panel.
Turn on the power switch and verify that the-
power module is operating correctly.
3. DES-7200 Accessories Carton
Determine whether the power module of-
the equipment is the required AC or DC
module
Cabling Rack (for DES-7210 only)-
Air Filter (for DES-7210 only)-
Handle-
Fan Tray-
Power Cable (for AC power only)-
Screws-
Documentation and Packing List-
Installation Check
Checklist
Unpacking Inspection
Requirements
Connecting the Console Port (RJ-45)
Management Options
Note:
The list above contains the items
included for a standard delivery. The
actual items delivered varies based
on the purchasing contract. Please
check the items received carefully
against the packing list or purchasing
EQPVTCEV+H[QWJCXGCP[SWGUVKQPUor if there are any problems, please
contact your distributor.

6/10 Slot Chassis-Based Switch 11
To connect a terminal to the console port:
Connect the supplied RJ-45-to DB-91.
adapter cable to the standard 9-pin serial
port on the PC. Connect the other end of
the cable to the console port on the switch.
Set the terminal emulation software as
follows:
Baud rate: 9600
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
Under Properties, select2. VT100 for
Emulation mode.
After you have correctly set up the terminal,3.
plug the power cable into the power
outlet on the back of the Switch. The boot
sequence appears in the terminal.
Press the Enter key at the password4.
prompts. There is no default password for
the Switch.
Enter the commands to complete your5.
desired tasks. Many commands require
administrator-level access privileges. See
VJG%.+4GHGTGPEG)WKFGQPVJGFQEWOGP-
tation CD for a list of all commands and
CFFKVKQPCNKPHQTOCVKQPWUKPIVJG%.+Telnet Management
7UGTUOC[CNUQCEEGUUVJGUYKVEJ%.+D[using PC’s Command Prompt. To access it
HTQO[QWTEQORWVGTWUGTUOWUVſTUVGPUWTGthat a valid connection is made through the
Ethernet port of the Switch and your PC, and
then click Start > Programs > Accessories >
Command Prompt on your computer. Once
the console window opens, enter the command
telnet 10.90.90.90FGRGPFKPIQPEQPſIWTGF+2CFFTGUUCPFRTGUU'PVGTQP[QWTMG[DQCTFYou should be directed to the opening console
UETGGPHQTVJG%.+QHVJGUYKVEJRTGUUVJGEnter key at the password prompts. There is no
default password for the Switch.
SNMP-Based Management
You can manage the Switch with D-Link
D-View or any SNMP-compatible console
program. The SNMP function is disabled by
default for D-Link managed switches. +H[QWCTGGPEQWPVGTKPIRTQDNGOUUGVVKPIWRyour network, please refer to the User’s Guide
VJCVECOGYKVJVJGUYKVEJ+VEQPVCKPUOCP[more rules, charts, explanations and examples
to help you get your network up and running.
#FFKVKQPCNJGNRKUCXCKNCDNGVJTQWIJQWTQHſEGUlisted online. To learn more about D-Link
products or marketing information, please visit
the website http://www.dlink.com.tw; for any
support issue, please visit the website http://
support.dlink.com.tw, which will re-direct you to
your appropriate local D-Link website.
Additional Information