D-Link DGS-1010MP User manual

Documentation is also available
on the D-Link website
This document will guide you through the
basic installation process for your new D-Link
10-Port Unmanaged Gigabit PoE Switch.
DGS-1010MP
Quick Installation Guide

1
ENGLISH
# LED Status Description
3
Link/Act/
Speed
(Ports 1
to 10)
Solid
amber
There is an active link negotiated at 10/100
Mbps on this port.
Blinking
amber
There is trac on the port at 10/100 Mbps.
Solid
green
There is an active link negotiated at
1000 Mbps on this port.
Blinking
green
There is trac on the port at 1000 Mbps.
4
PoE
(Ports
1 to 8)
Solid
green
The port is providing power to the
connected PoE-powered device.
Blinking
amber
Indicates a PoE-powered device is
connected to this PoE port, but the switch
has insucient remaining power budget
to power the device.
O There is no PoE-powered device
connected to this port.
Table 1
Front Panel Connectors
1 2 3
Figure 2
#Item Description
1Ports 1 ~ 8
10/100/1000 Mbps PoE-capable ports for
connecting Ethernet devices and PoE-
powered devices.
2Port 9
10/100/1000 Mbps Ethernet uplink port
for connecting to another switch using an
Ethernet cable.
3Port 10 100/1000 Mbps SFP uplink port for installing a
compatible SFP transceiver.
Table 2
Rear Panel Connectors
1 2 34
Figure 3
#Item Description
1Power Input This is used to connect the power cable to the
switch.
2Power Cord
Retainer Slot
This is used for securing the power cord
retainer to the switch.
3Switch GND This is used to connect the switch to ground.
4Kensington
Lock Input
This is used to attach a Kensington security
lock.
Table 3
Before You Begin
This Quick Installation Guide gives you step-by-
step instructions for setting up your DGS-1010MP
10-Port Unmanaged Gigabit PoE Switch. The model
you have purchased may appear slightly dierent
from the one shown in the illustrations. For more
detailed information about the switch, please refer
to the User Manual.
Package Contents
This DGS-1010MP package should include the
following items:
• 1 x DGS-1010MP
• 1 x Power cord
• 1 x Power cord retainer
• 1 x Rack mount kit and rubber feet
• 1 x Quick Installation Guide
If any of the above items are damaged or missing,
please contact your local D-Link reseller.
Hardware Overview
LED Indicators
1 2 3
4
Figure 1
# LED Status Description
1Power
Solid
green
The device is powered on.
O The device is powered o.
2PoE Max
Solid
amber
Indicates that the total PoE power output
of the switch has exceeded the Guard
Band threshold of 118 W, but is still below
the total budget of 125 W.
Blinking
amber
The total PoE budget of 125 W has been
exceeded and no additional devices can
be powered through the switch.
O The total PoE power consumption is below
the 118 W Guard Band threshold.

2
ENGLISH
Hardware Installation
Before You Begin
Observe the following precautions to help prevent
shutdowns, equipment failures, and personal injury:
• Install the DGS-1010MP in a cool and dry
place. Refer to the technical specications in
the user manual for the acceptable operating
temperature and humidity ranges.
• Install the switch in a site free from strong
electromagnetic sources, vibration, dust, and
direct sunlight.
• Leave at least 10 cm of space to the left and right-
hand side of the switch for ventilation.
• Visually inspect the power connector and make
sure that it is fully secured to the power cord.
• Do not stack any devices on top of the switch.
Using the Switch on a Flat Surface
The included rubber feet can be placed on the
bottom of the device to prevent it from damaging
the surface it is placed on.
1. Remove the rubber feet from the backing.
2. Stick one pad on each corner on the bottom of
the switch.
Figure 4
Mounting the Switch in a Rack
The DGS-1010MP can be mounted into a standard
19” server rack.
1. Attach the included mounting brackets to the
sides of the switch and secure them using the
provided screws.
Figure 5
2. Install the switch into the rack.
3. Use the screws that were provided with the rack
to secure the switch to the rack.
Figure 6
Grounding the Switch
This step must be completed before powering on
the switch.
Required tools and equipment for grounding
• Grounding screw (included) and one M4x6
(metric) pan-head screw (not included).
• Grounding cable (not included). The grounding
cable should be sized according to local and
national installation requirements. Depending
on the power supply and system, a 12 to 6 AWG
copper conductor is required for installation.
Commercially available 6 AWG wire is
recommended. The length of the cable depends
on the proximity of the switch to proper
grounding facilities.
• A screwdriver (not included).
Note: Verify that the system is powered o.
1. Remove the grounding screw from the back of
the device and place the #8 terminal lug ring of
the grounding cable on top of the grounding
screw opening.
2. Insert the grounding screw back into the screw
opening and use a screwdriver to tighten the
grounding screw.

3
ENGLISH
3. Attach the terminal lug ring at the other end
of the grounding cable to an appropriate
grounding source.
4. Verify that the connection between the
grounding connector on the switch and the
grounding source is secure.
Powering On the Switch
1. Connect the power cord to the power connector
on the switch.
2. Plug the other end of the power cord into a
nearby power socket.
Attaching the Power Cord Retainer
To prevent the power from accidently being
disconnected, it is recommend to install the included
power cord retainer.
1. With the smooth side facing up, insert the tie into
the opening below the power socket.
Figure 7
2. Plug the power cord into the power socket on
the switch.
Figure 8
3. Slide the retainer through the tie until it has
reached the end of the power cord.
Figure 9
4. Wrap the tie of the retainer strip around the
power cord and back into the retainer to lock it.
Fasten the tie until the power cord is secured.
Figure 10
Connecting to the Network
The switch can be integrated into the network
through one of the following connection methods:
Switch to End Node or Powered Device
Use a standard Ethernet cable to connect the switch
to PCs with an 10/100/1000 Mbps RJ-45 interface,
or connect and power remote IEEE 802.3af/at-
compliant devices, such as IP cameras or IP phones
using PoE.

4
ENGLISH
Switch to Hub or Switch
Connect the switch to another switch or hub using
the RJ-45 or SFP uplink ports.
Switch to Server
Connect the switch to a network backbone or
network server using the RJ-45 or SFP uplink ports.

5
ENGLISH
NOTES

Version 1.10(NA)_130x183
November 5, 2018
5402132
Copyright ©2018 All rights reserved. D-Link and the D-Link logo are registered trademarks of D-Link Corporation or its
subsidiaries. Other trademarks are the property of their respective owners. Product specications, size and shape are subject to
change without notice, and actual product appearance may dier from that depicted on the packaging. Visit dlink.com (US) or
dlink.ca (Canada) for more details.
Technical Support
Having trouble installing your new product? D-Link’s website contains the latest
user documentation and software updates for D-Link products. U.S. and Canadian
customers can contact D-Link Technical Support through our website.
United States
Internet: http://support.dlink.com
Canada
Internet: http://support.dlink.ca