D-Link DGS-1024D - Switch User manual

DGS-1016D/DGS-1024D
Quick Installation Guide
Gigabit Desktop Switch
Documentation is also available on the D-Link website
This document will guide you
through the basic installation
process for your new D-Link
Gigabit Desktop Switch.

11
ENGLISH
About This Guide
The D-Link DGS-1016D/1024D 16/24-Port Gigabit
Desktop Switch is a stand-alone plug-and-play
device. This Quick Installation Guide gives step-by-
step instructions for setting up the device. The model
you have purchased may appear slightly different
from the images shown in this guide. For more
detailed information about the switch, installation
process, making network connections, and technical
specications, please refer to the User Manual or visit
http://www.dlink.com
Package Contents
These are the items included with your purchase:
• D-Link DGS-1016D 16-Port or DGS-1024D
24-Port 10/100/1000BASE-T Gigabit
Ethernet Switch
• AC power cord
• Four rubber feet
• Screws and two mounting brackets
• Quick Install Guide
• Power cord retainer
• Tie wrap
If any of the above items are missing, please contact
your D-Link reseller for replacement.
Before Connecting to the
Network
As with any electronic device, you should place
the equipment where it will not be subjected to
extreme temperatures, humidity, or electromagnetic
interference. Specically, the site you select should
meet the following requirements:
A. Install the DGS-1016D / DGS-1024D in a fairly
cool and dry place. See Technical Specications
page in the manual for the acceptable operation
temperature and humidity ranges.
B. Install the switch in a site free from vibration, dust,
and direct sunlight.
C. Leave at least 10cm of space on the left and right
hand side of the switch for ventilation.
D. Visually inspect the power cable and ensure that
it is rmly inserted into a suitable power outlet.
Switch Installation
The DGS-1016D/1024D can easily be mounted in an
EIA standard size 19-inch rack which can be placed
in a wiring closet with other equipment or placed on a
desktop or shelf.
Desktop or Shelf Installation
When installing the switch on a desktop or shelf, use
the rubber feet provided. Position and apply the rubber
feet to the bottom corners of the DGS-1016D/1024D
switch.
Rack Installation
To install in a rack, attach the mounting brackets
to the switch’s side panels (one on each side) and
secure them with the screws provided. Then, use the
hardware provided with the equipment rack to mount
the switch in the rack.

22
ENGLISH
Installing a Power Cord
Retainer
Installation of a power cord retainer is recommended
to prevent accidental removal of the AC power cord.
A. Insert a tie wrap with the rough side facing down
into the hole below the power socket.
Insert tie wrap
B. Connect the AC power cord into the AC power
inlet of the switch.
Connect the power cord to the switch
C. Attach the retainer to the tie wrap and slide it up to
the end of the cord.
Attach the retainer to the tie wrap
D. Wrap the retainer around the power cord and
place the free end into the fastener.
Wrap the retainer around the power cord
E. Fasten the retainer by pulling on it until secure.
Secure the power cord
F. Connect the AC power cord to an electrical outlet.
Connecting the DGS-1016D/
DGS-1024D to your network
A. Power
The switch can be used with AC power sources 100
- 240 VAC, 50 - 60 Hz. The switch’s power supply
will adjust to the local power source automatically
and may be turned on without having any or all LAN
segment cables connected.
B. Ethernet
These ports support network speeds of 10 Mbps,
100 Mbps, or 1000 Mbps, and can operate in
half-duplex and full-duplex transfer modes. These
ports also support automatic MDI/MDIX crossover
detection, which gives the switch true “plug and
play” capabilities. Just connect any network cable
between the switch and the device, and the switch
will automatically detect the settings of the device and
adjust itself accordingly.

33
ENGLISH
LED Indicators
The LED indicators allow you to monitor, diagnose,
and troubleshoot potential problems with the switch,
connection, or attached devices.
LED Color State Indication
Power Green Light on Power on
Light off Power off
Link/Act/
Speed
Green
On Connection (or link) at
1000 Mbps
Blinking
Reception or
Transmission at 1000
Mbps
Amber
On Connection (or link) at
10/100 Mbps
Blinking
Reception or
Transmission at 10/100
Mbps
Cable Diagnostics (During Boot Only)
Port Link/Act/
Speed LED Color Status
Green No Faults Detected /Good Cable
Connection
Amber Open or Short Circuit
DIP Switches
The DIP switches on the front panel allow easy
conguration of the advanced features of the DGS-
1016D and DGS-1024D.
DIP
Switch Function Controlled Default
EEE Enables/Disable IEEE 802.az
Energy-Efcient Ethernet Feature Off
Flow
Control
Enables/Disable Flow Control
Feature On
Port
Isolation
and
Storm
Control
Port Isolation: See Below
Storm Control: When enabled, a
broadcast storm control threshold
value of 128 kbps will be applied
to incoming broadcast packets on
all ports.
Off
Port Isolation:
DGS-1016D - When enabled, ports 1 to 15 will
be isolated from each other, but will still be able to
communicate with port 16. Port 16 will be able to
communicate with all the ports available on this switch.
DGS-1024D - When enabled, ports 1 to 23 will
be isolated from each other, but will still be able to
communicate with port 24. Port 24 will be able to
communicate with all the ports available on this switch.
Note: The switch must be power cycled
after changing DIP Switch settings for new
settings to take effect.
Additional Information
Additional help and product information is available
online at http://www.dlink.com.
Warranty Information
Please visit http://warranty.dlink.com/ for warranty
information for your region.
©2015 D-Link Corporation. All rights reserved.
Trademarks or registered trademarks are the property
of their respective holders. Software and specications
subject to change without notice.

NOTES

Ver.7.20(CA)_130X183
2015/06/10
29072600S1016D8

DGS-1016D/DGS-1024D
Guide d'installation rapide du
commutateur Gigabit pour ordinateur de
bureau
Documentation également disponible sur le site Web de D-Link
Ce document vous guidera tout au
long de la procédure d'installation
de base de votre nouveau Gigabit
pour ordinateur de bureau de D-Link.