D-Link DXS-3610 Series Manual

DXS-3610 Series 100 Gigabit Ethernet Managed Switch
Hardware Installation Guide

DXS-3610 Series Layer 3 Stackable 10GbE Managed Switch Hardware Installation Guide
ii
Information in this document is subject to change without notice. Reproduction in any manner whatsoever, without the written
permission of D-Link Corporation, is strictly forbidden.
Trademarks used in this text: D-Link and the D-LINK logo are trademarks of D-Link Corporation; Microsoft and Windows are
registered trademarks of Microsoft Corporation.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or
their products. D-Link Corporation disclaims any proprietary interest in trademarks and trade names other than its own.
© 2020 D-Link Corporation. All rights reserved.
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
D-Link Corporate
17595 Mt. Hermann Street
Fountain Valley, CA 92708
[phone]
CE Mark Warning
This equipment is compliant with Class A of CISPR 32. In a residential environment, this equipment may cause radio interference.
Avertissement Concernant la Marque CE
Cet équipement est conforme à la classe A de la norme CISPR 32. Dans un environnement résidentiel, cet équipement peut
provoquer des interférences radio.
VCCI Warning
この装置は、クラス A機器です。この装置を住宅環境で使用すると電波妨害を引き起こすことがあります。この場合には使用者が
適切な対策を講ずるよう要求されることがあります。 VCCI-A
BSMI Notice
此為甲類資訊技術設備，於居住環境中使用時，可能會造成射頻擾動，在此種情況下，使用者會被要求採取某些適當的對策。
Safety Compliance
Warning: Class 1 Laser Product: When using a fiber optic media expansion module, never look at the transmit laser while it is
powered on. In addition, never look directly at the fiber TX port and fiber cable ends when they are powered on.
Avertissement: Produit Laser de Classe 1: Ne regardez jamais le laser tant qu’il est sous tension. Ne regardez jamais
directement le port TX (Tramsmission) à fibres optiques et les embouts de câbles à fibres optiques tant qu’ils sont sous tension.

DXS-3610 Series Layer 3 Stackable 10GbE Managed Switch Hardware Installation Guide
iii
Table of Contents
Intended Readers ................................................................................................................................................... v
Typographical Conventions .................................................................................................................................... v
Notes and Cautions ................................................................................................................................................ v
1. Introduction........................................................................................................................................................... 1
Switch Description .................................................................................................................................................. 1
Switch Series .......................................................................................................................................................... 1
Package Contents .................................................................................................................................................. 1
2. Hardware Components ........................................................................................................................................ 2
Front Panel Components........................................................................................................................................ 2
Front Panel LED Indicators ............................................................................................................................... 3
Rear Panel Components ........................................................................................................................................ 5
Rear Panel LED Indicators................................................................................................................................ 6
Side Panel Components ......................................................................................................................................... 6
3. Installation ............................................................................................................................................................. 7
Installation Guidelines............................................................................................................................................. 7
Installing the Switch without a Rack ....................................................................................................................... 7
Installing the Switch in a Standard 19" Rack.......................................................................................................... 8
Installing Transceivers into the Transceiver Ports................................................................................................10
Installing PSU Modules into the PSU Module Slots .............................................................................................12
Installing AC PSU Modules ............................................................................................................................. 12
Installing DC PSU Modules .............................................................................................................................13
Installing Fan Modules into the Fan Module Slots................................................................................................16
Smart Fans ...................................................................................................................................................... 17
4. Switch Connections ........................................................................................................................................... 18
Stacking the Switch ..............................................................................................................................................18
Switch to Switch....................................................................................................................................................20
Switch to Server....................................................................................................................................................20
Switch to End Node ..............................................................................................................................................21
5. Switch Management ........................................................................................................................................... 22
Management Options ........................................................................................................................................... 22
Command Line Interface (CLI) ............................................................................................................................. 22
Connecting to the Console Port ......................................................................................................................22
Logging into the CLI ........................................................................................................................................23
Creating a User Account .................................................................................................................................23
Configuring the IP Address.............................................................................................................................. 23
Web User Interface (Web UI) ............................................................................................................................... 24
Connecting to the Web UI ...............................................................................................................................24
Logging into the Web UI..................................................................................................................................24
Web Interface Navigation ................................................................................................................................ 25
SNMP-based Management .................................................................................................................................. 26
Connecting using SNMP ................................................................................................................................. 26
Traps................................................................................................................................................................26
Management Information Base (MIB) ............................................................................................................. 26
Appendix A - Technical Specifications....................................................................................................................... 27
Appendix B - Cables and Connectors......................................................................................................................... 32
Ethernet Cable......................................................................................................................................................32
Console Cable ......................................................................................................................................................33

DXS-3610 Series Layer 3 Stackable 10GbE Managed Switch Hardware Installation Guide
iv
Safety/Sécurité .............................................................................................................................................................. 34
Safety Instructions ................................................................................................................................................ 34
Safety Cautions ...............................................................................................................................................34
Consignes de sécurité ..........................................................................................................................................35
Précautions de sécurité................................................................................................................................... 35
General Precautions for Rack-Mountable Products ............................................................................................. 37
Protecting Against Electrostatic Discharge...........................................................................................................38
Warranty & Technical Support .................................................................................................................................... 39

DXS-3610 Series Layer 3 Stackable 10GbE Managed Switch Hardware Installation Guide
v
Intended Readers
The DXS-3610 Series 100 Gigabit Ethernet Managed Switch Hardware Installation Guide contains detailed
information about the hardware specifications of the switches in this series. It also contains brief information on how to
configure and manage a switch in this series. This manual is intended for advanced level users that are familiar with
network management concepts and terminology. For all practical reasons, all the switches in this series will simply be
referred to as the Switch throughout this manual.
Typographical Conventions
Convention Description
Boldface Font This convention is used to place emphasis on keywords. It also indicates a button,
toolbar icon, menu, menu item, system message, or a prompt appearing on the
screen. For example, click the Apply button.
Initial capital letter This convention is used to indicate a window name or keyboard key. For example,
press the Enter key.
Blue Courier Font
This convention is used to represent a CLI example.
Notes and Cautions
NOTE: A note indicates important information that helps you make better use of your device.
CAUTION: A caution indicates a potential for property damage, personal injury, or death.
ATTENTION :Une précaution indique un risque de dommage matériel, de blessure corporelle ou de
mort.

DXS-3610 Series Layer 3 Stackable 10GbE Managed Switch Hardware Installation Guide
1
1. Introduction
Switch Description
Switch Series
Package Contents
Switch Description
The DXS-3610 series is the latest generation of Managed switches from D-Link. Switches in this series feature a wide
selection of different ports types and speeds that can be used to interconnect a variety of networking devices to
communicate with each other. The QSFP28 and SFP+ ports, with fiber-optical cabling, can be used to uplink
connections that may span over great distances. Switches in this series also implement D-Link’s innovative third
generation Green Ethernet technology (IEEE 802.3az) to save power from links that are inactive by turning LEDs off
based on a customized schedule and by allowing ports to automatically enter a hibernated state.
Switch Series
The following switches are part of the DXS-3610 series:
•DXS-3610-54T - L3 stackable 10GbE managed switch with 48 RJ45 10 Gbps and 6 QSFP28 100 Gbps ports
•DXS-3610-54S - L3 stackable 10GbE managed switch with 48 SFP+ 10 Gbps and 6 QSFP28 100 Gbps ports
Package Contents
Open the shipping carton of the Switch and carefully unpack its contents. The carton should contain the following
items:
•One DXS-3610 series switch
•Two pre-installed AC power supply modules (DXS-PWR700AC)
•Five pre-installed fan modules with front-to-back-airflow (DXS-FAN200)
•Two AC power cords
•One RJ45 to RS-232 console cable
•One micro-USB to Type-A USB cable
•Four rubber feet with adhesive backing
•One rack mounting kit, containing two brackets and a number of screws
•One quick installation guide
NOTE: If any item is missing or damaged, please contact your local D-Link reseller for replacement.

DXS-3610 Series Layer 3 Stackable 10GbE Managed Switch Hardware Installation Guide
2
2. Hardware Components
Front Panel Components
Rear Panel Components
Side Panel Components
Front Panel Components
The front panel features components like LED indicators, a Console port, an MGMT port, a micro-USB port, a reset
button, and a variety of Ethernet ports. These components are described in detail below.
This following table lists the front panel components on all the switches in the series:
Port Description
Console Port The console port can be used to connect to the CLI of the Switch. This Out-Of-
Band (OOB) connection can be made from the serial port of an administrative node
to the RJ45 console port on the front panel of the Switch. The console cable
(included in the package) must be used for the connection.
MGMT Port The management (MGMT) port can be used to connect to the CLI or the Web UI of
the Switch. SNMP-enabled connectivity can also be made through this port. This
OOB connection can be made from a standard LAN adapter to the RJ45 MGMT
port on the front panel of the Switch. This connection operates at 10/100/1000
Mbps.
Micro-USB Port The micro-USB port provides additional storage space for firmware images and
configuration files that can be copied to and from the Switch. Only endpoint
devices like USB flash drives are supported.
Reset Button The reset button can be used to reboot the switch or to reset the switch to its
factory default settings depending on how long this button is pressed.
•Press and hold for less than 5 seconds
This reboots the Switch. All unsaved configurations will be lost.
•Press and hold for between 5 and 10 seconds
This resets the software configuration on the Switch to the factory default
settings.
Information Tag The sliding information tag is discretely located on the front panel, right next to the
QSFP28 ports, and contains the product code, hardware version, serial number,
and MAC address of the Switch. The QR code can be scanned to quickly obtain
the abovementioned information.
Figure 2-1 DXS-3610-54T Front Panel
This following table lists the front panel components unique to the DXS-3610-54T:
Port Type Port Number Description
RJ45 Ports
(1/10 Gbps)
Ports 1 to 48 This switch is equipped with 48 RJ45 Ethernet ports that can
operate at 1 and 10 Gbps wire-speeds.
QSFP28 Ports
(40/100 Gbps)
Ports 49 to 54 This switch is equipped with 6QSFP28 ports that can operate
at 40 and 100 Gbps wire-speeds and support a wide
collection of QSFP+/QSFP28 transceivers.

DXS-3610 Series Layer 3 Stackable 10GbE Managed Switch Hardware Installation Guide
3
Figure 2-2 DXS-3610-54S Front Panel
This following table lists the front panel components unique to the DXS-3610-54S:
Port Type Port Number Description
SFP+ Ports
(1/10 Gbps)
Ports 1 to 48 This switch is equipped with 48 SFP+ ports that can operate
at 1 and 10 Gbps wire-speeds and support a wide collection
of SFP/SFP+ transceivers.
QSFP28 Ports
(40/100 Gbps)
Ports 49 to 54 This switch is equipped with 6QSFP28 ports that can operate
at 40 and 100 Gbps wire-speeds and support a wide
collection of QSFP+/QSFP28 transceivers.
Front Panel LED Indicators
The LED indicators provide valuable information in a variety of ways like their color, blinking times, and location.
Figure 2-3 DXS-3610-54T Front Panel LED Indicators
Figure 2-4 DXS-3610-54S Front Panel LED Indicators
The front panel LED indicators are described in the following table:
LED Color Status Description
Locator Blue On (Solid) User logged in
- Off Locator function is disabled
Power Green On (Solid) Power on
On (Blinking) Performing system self-test
Amber On (Solid) PSU failed or Voltage/Current/Temperature too high
- Off Power off
Status Green On (Solid) POST passed and normal operation
On (Blinking) POST in progress
Amber On (Blinking) POST/PSU/Fan failed or Temperature too high
- Off Power off
Fan Green On (Solid) Fan operation normal

DXS-3610 Series Layer 3 Stackable 10GbE Managed Switch Hardware Installation Guide
4
LED Color Status Description
Amber On (Blinking) Fan error
- Off Power off
Link/Act
(Out-Of-Band port)
Green On (Solid) Active connection through the port
On (Blinking) Data transmitted and received through the port
- Off Inactive connection, no link present, or port disabled
Link/Act
(10GE RJ45 ports)
Green On (Solid) Active connection at 10 Gbps through the port
On (Blinking) Data transmitted and received through the port
Amber On (Solid) Active connection at 1 Gbps through the port
On (Blinking) Data transmitted and received through the port
- Off Inactive connection, no link present, or port disabled
Link/Act
(10GE SFP+ ports)
Green On (Solid) Active connection at 10 Gbps through the port
On (Blinking) Data transmitted and received through the port
Amber On (Solid) Active connection at 1 Gbps through the port
On (Blinking) Data transmitted and received through the port
- Off Inactive connection, no link present, or port disabled
Link/Act
(100GE QSFP28 ports)
White
(LED 1)
On (Solid) Active connection at 100 Gbps through the port
On (Blinking) Data transmitted and received through the port
Blue
(LED 4)
On (Solid) Active connection at 40 Gbps through the port
On (Blinking) Data transmitted and received through the port
- Off Inactive connection, no link present, or port disabled
Stacking (Master)
(100GE QSFP28 ports)
White
(LED 1)
Amber
(LED 2)
On (Solid) Active connection at 100 Gbps through the port and the
Switch is the Master switch in the stack
On (Blinking) Data transmitted and received through the port
- Off No link present
Stacking (Slave)
(100GE QSFP28 ports)
Amber
(LED 3)
Blue
(LED 4)
On (Solid) Active connection at 100 Gbps through the port and the
Switch is a Slave switch in the stack
On (Blinking) Data transmitted and received through the port
- Off No link present
The behavior of the LEDs during the booting or rebooting process is described per phase in the following table:
Phase LED(s) Behavior
Phase 1 Locator Lights solid blue during this phase.
Power Remains off during this phase.
Status Remains off during this phase.
Fan Remains off during this phase.
Port Link/Act Remains off during this phase.
Phase 2 Locator Turns off during this phase.
Power Turns off during this phase.
Status Turns off during this phase.

DXS-3610 Series Layer 3 Stackable 10GbE Managed Switch Hardware Installation Guide
5
Phase LED(s) Behavior
Fan Turns off during this phase.
Port Link/Act Lights solid amber during this phase.
Phase 3 Locator Lights solid green during this phase.
Power Lights solid green during this phase.
Status Blinks green during this phase.
Fan Lights solid green during this phase.
Port Link/Act Lights solid amber during this phase.
System Ready All Return to normal operation behavior.
Rear Panel Components
The rear panel features components like LED indicators, PSU (Power Supply Unit) modules, fan modules, and an
electrical grounding point. These components are described in detail below.
CAUTION: When two PSU modules are installed, they must be the same type (two ACs or two DC) and
also use the same airflow direction (back-to-front or front-to-back).
ATTENTION :Lorsque deux modules d'alimentation sont installés, ils doivent être du même type (deux
CA ou deux CC) et utiliser le même sens du flux d'air (dos à dos ou face à face).
Figure 2-5 DXS-3610-54T/DXS-3610-54S Rear Panel (AC PSU)
Figure 2-6 DXS-3610-54T/DXS-3610-54S Rear Panel (DC PSU)
This following table lists the rear panel components on the Switch:
Port Description
Switch GND Use an electrical grounding wire and connect one end of the wire to the switch
GND and the other end of the wire to an electrical grounding point most commonly
found on the Switch mounting rack itself.
Fan Modules These are five hot-swappable, redundant (4+1) fan module slots on the rear panel
of the Switch. The following fan modules can be installed in these slots:
•DXS-FAN200 (Fan module with Front-to-Back airflow)
•DXS-FAN200-B (Fan module with Back-to-Front airflow)
When five fans modules are installed, four fan modules will be active and the fifth
fan module will be passive until one of the four active fan modules fail.
Power Supply Module Slots There are two load-sharing power supply module slots on the rear panel of the
Switch. The following power supply modules can be installed in these slots:
•DXS-PWR700AC (AC PSU with Front-to-Back airflow)
•DXS-PWR700AC-B (AC PSU with Back-to-Front airflow)
•DXS-PWR1000DC (-48V DC PSU with Front-to-Back airflow)

DXS-3610 Series Layer 3 Stackable 10GbE Managed Switch Hardware Installation Guide
6
Port Description
•DXS-PWR1000DC-B (-48V DC PSU with Back-to-Front airflow)
When two PSU modules are installed, they will share the power load between
them.
Rear Panel LED Indicators
The LED indicators provide valuable information in a variety of ways like their color, blinking times, and location.
Figure 2-7 DXS-3610-54T/DXS-3610-54S Rear Panel LED Indicators
The rear panel LED indicators are described in the following table:
LED Color Status Description
Power Supply Module Green On (Solid) Normal power supply module operation
On (Blinking) PSU module is off but standby power is supplied
Amber On (Solid) PSU/Fan failed or PSU shutdown due to critical event
On (Blinking) Warning event occurred (Power/Current/Temperature
too high or fan is too slow)
- Off Power off or PSU is on but with warning events
Fan Module Green On (Solid) Fan operation is normal
On (Blinking) Fan error occurred
- Off Power off
Side Panel Components
The side panels feature components like rack-mounting screw holes and rack-mounting slider pegs.
Figure 2-8 DXS-3610-54T/DXS-3610-54S Side Panels

DXS-3610 Series Layer 3 Stackable 10GbE Managed Switch Hardware Installation Guide
7
3. Installation
Installation Guidelines
Installing the Switch without a Rack
Installing the Switch in a Standard 19" Rack
Installing Transceivers into the Transceiver Ports
Installing PSU Modules into the PSU Module Slots
Installing Fan Modules into the Fan Module Slots
Installation Guidelines
This section will discuss the hardware installation guidelines that the user must follow in order to properly and safely
install this switch into the appropriate environment.
•Visually inspect the power cord and see that it is fully secured to both the power connector, on the Switch, and
the electrical outlet that supplies power.
•Install the Switch in a fairly cool and dry place within the acceptable operating temperature and humidity
ranges. For more information about the acceptable operating temperature and humidity ranges, refer to the
Physical and Environmental section.
•Install the Switch in a site free from strong electromagnetic field generators such as motors, vibration, dust, and
direct exposure to sunlight.
Installing the Switch without a Rack
This section is used to guide the user through installing the Switch in an area other than a switch rack. Attach the
included rubber feet to the bottom of the Switch. Take note that there should be marked blocks on the bottom of the
Switch to indicate where to attach the rubber feet. These markings are usually found in each corner on the bottom of
the device. The rubber feet cushion the Switch, protecting the casing from scratches and preventing it from scratching
other surfaces.
Figure 3-1 Attaching rubber feet to the Switch
Install the Switch on a sturdy, level surface that can support the weight of the Switch. Do not place any heavy objects
on the Switch. The power outlet should be within 1.82 meters (6 feet) of the Switch. Make sure that there is proper

DXS-3610 Series Layer 3 Stackable 10GbE Managed Switch Hardware Installation Guide
8
heat dissipation from and adequate ventilation around the Switch. Leave at least 10 cm (4 inches) of space at the
front, sides, and rear of the Switch for ventilation.
Installing the Switch in a Standard 19" Rack
This section is used to guide the user through installing the Switch into a switch rack. The Switch can be mounted in a
standard 19"(1U) rack using the rack mounting kit included in the package contents.
Fasten the frontal rack-mounting brackets to the front-sides of the Switch using the screws provided.
Figure 3-2 Attaching the frontal rack-mounting brackets
Figure 3-3 Frontal rack-mounting brackets attached

DXS-3610 Series Layer 3 Stackable 10GbE Managed Switch Hardware Installation Guide
9
Slide the rear rack-mounting slider brackets into place, as illustrated below.
Figure 3-4 Positioning the rear rack-mounting brackets
Fasten the mounting brackets in any available open space in the rack using the screws provided.
Figure 3-5 Installing the Switch in a Rack
Make sure that there is adequate space around the Switch to allow for proper airflow, ventilation, and cooling.

DXS-3610 Series Layer 3 Stackable 10GbE Managed Switch Hardware Installation Guide
10
Installing Transceivers into the Transceiver Ports
Switches in this series are equipped with QSFP28 ports and the DGS-3610-54S is equipped with SFP+ ports. These
ports can be used to connect various networking devices to this switch that do not support the standard RJ45 wiring
connection. These ports are generally used to connect this switch to optical fiber connections and can be used to
connect devices to the Switch over great distances. The maximum distance that the RJ45 wiring connection can reach
is 100 meters. Fiber optic connections can span several kilometers.
NOTE:
•The DXS-3610-54T and DXS-3610-54S is equipped with QSFP28 ports.
•Only the DXS-3610-54S is equipped with SFP+ ports.
The figure below illustrates how to properly insert QSFP+/QSFP28 transceivers into the 100GE QSFP28 ports.
Figure 3-6 Inserting QSFP+/QSFP28 transceivers into the QSFP28 ports

DXS-3610 Series Layer 3 Stackable 10GbE Managed Switch Hardware Installation Guide
11
The figure below illustrates how to properly insert SFP/SFP+ transceivers into the 10GE SFP+ ports.
Figure 3-7 Inserting SFP/SFP+ transceivers into the SFP+ ports
NOTE: For the full list of D-Link SFP/SFP+/QSFP+/QSFP28 transceivers that are supported on the
Switch, refer to the Supported SFP/SFP+/QSFP+/QSFP28 Transceivers table on page 30.
NOTE: Only use pluggable optical modules and Direct-Attach Cables (DAC) that meet the following
regulatory requirements:
•Class 1 Laser Product
•UL and/or CSA registered component for North America
•FCC 21 CFR Chapter 1, Sub-chapter J in accordance with FDA & CDRH requirements
•IEC/EN 60825-1/-2: 2007 2nd edition or later, European Standard

DXS-3610 Series Layer 3 Stackable 10GbE Managed Switch Hardware Installation Guide
12
Installing PSU Modules into the PSU Module Slots
The Switch supports the installation of AC PSU (Power Supply Unit) modules and/or DC PSU modules into the PSU
module slots.
NOTE: The PSU modules support a specific airflow direction. This airflow direction must be the same as
the fan module(s) installed. The default airflow direction is front-to-back on all the installed PSU
modules and fan modules.
Installing AC PSU Modules
The Switch is shipped with two pre-installed AC PSU modules. This section can be referenced when one or more AC
PSU modules need to be replaced.
CAUTION: Make sure that the AC power cord is removed from the Switch and that the Switch is not
receiving any power. The power, fan, and other LED indicators must be off.
ATTENTION :Assurez-vous que le cordon d'alimentation CA est débranché du commutateur et que le
commutateur ne reçoit pas de courant. L'alimentation, le ventilateur et les autres voyants à LED
doivent être éteints.
To remove an existing AC PSU module, press the release clip to the side and gently pull the AC PSU module out of
the PSU module slot.
Insert the new AC PSU module into the PSU module slot until the release clip securely clicks into place.
Figure 3-8 Installing an AC PSU Module

DXS-3610 Series Layer 3 Stackable 10GbE Managed Switch Hardware Installation Guide
13
Figure 3-9 Installed AC PSU Module
A second AC PSU module can be installed into the second PSU module slot labelled PSU-2. If the primary AC PSU
fails, the second AC PSU is used to provide AC power to the Switch. This takes place immediately and automatically.
When the AC PSU module is securely installed, plug one end of the AC power cord into the AC power socket on the
AC PSU module and the other end of the AC power cord into a properly grounded AC power source outlet. There is
no power switch/button on the Switch. The system will automatically power on and adjust its power settings to adapt to
any voltage supplied within the 100~240VAC range at 50~60Hz.
Installing DC PSU Modules
Switches in this series can also be shipped with two pre-installed DC PSU modules. This section can be referenced
when one or more DC PSU modules need to be replaced.
CAUTION: Make sure that the DC power supply source is disconnected from the Switch and that the
Switch is not receiving any power. The power, fan, and other LED indicators must be off.
ATTENTION :Assurez-vous que la source d'alimentation CC est déconnectée du commutateur et que
celui-ci n’est pas alimenté. L'alimentation, le ventilateur et les autres voyants à LED doivent être
éteints.
To remove an existing DC PSU module, press the release clip to the side and gently pull the DC PSU module out of
the power supply module slot.

DXS-3610 Series Layer 3 Stackable 10GbE Managed Switch Hardware Installation Guide
14
Insert the new DC PSU module into the power supply module slot until the release clip securely clicks into place.
Figure 3-10 Installing a DC PSU Module
Figure 3-11 Installed DC PSU Module
A second DC PSU module can be installed into the second PSU module slot labelled PSU-2. If the primary DC PSU
fails, the second DC PSU is used to provide DC power to the Switch. This takes place immediately and automatically.

DXS-3610 Series Layer 3 Stackable 10GbE Managed Switch Hardware Installation Guide
15
When the DC PSU module is securely installed, insert the one end of the DC power cord, with the plug, into the
matching DC power socket on the DC PSU module and the other end of the DC power cord to the DC power source (-
48VDC/5.2A). Make sure that the connection polarity (positive and negative) is correct to avoid any damaged.
Figure 3-12 Connecting a DC Battery to the DC Power Supply Module
There is no power switch/button on the Switch. The Switch will power on automatically.
CAUTION: Before connecting the DC power cable to the DC power input socket, on the switch, the DC
power cable must be properly connected to DC source, at your facility, by a qualified, licensed
electrician.
ATTENTION :Avant de brancher le câble d'alimentation CC à la prise d'alimentation CC, sur le
commutateur, le câble d'alimentation CC doit être correctement branché à la source CC, dans votre
installation, par un électricien qualifié et agréé.
CAUTION: When installing a DC-powered switch, ground the chassis before connecting the switch to
the DC power source and following the following instructions:
•Use a minimum of 18 AWG stranded copper wire for grounding. The wire should be long enough
to reach from the installed switch to the facility ground point.
•Ground additional hardware appropriately to the earth ground connection at your site.
•Connect the DC power cable to a DC main circuit breaker rated no greater than 15A.
ATTENTION :Lorsque vous installez un commutateur alimenté en courant continu, mettez le châssis à
la terre avant de connecter le commutateur à la source d'alimentation en courant continu et suivez
les instructions ci-après:
•Utilisez un minimum de fil de cuivre toronné de 18 AWG pour la mise à la terre. Le fil doit être
suffisamment long pour aller du commutateur installé au point de mise à la terre de l'installation.
•Mettez à la terre le matériel supplémentaire en fonction de la prise de terre de votre site.
•Connectez le câble d'alimentation DC à un disjoncteur principal DC d'une puissance maximale de
15A.