D-Link DGS-3630-28SC User manual

D-Link
DGS-3630-28SC
20 1000Base-X SFP ports + 4 Combo 10 100 1000Base-T SFP ports +
4 10 GbE SFP+ ports L3 Stackable Managed Switch
Управляемый стекируемый коммутатор 3 уровня с 20 портами 1000Base-X
SFP, 4 комбо-портами 100 1000Base-T SFP и 4 портами 10GBase-X SFP+
Quick Installation Guide
Краткое руководство по установке

Infor ation in this docu ent is subject to change without notice.
© 2018 D-Link Corporation. All rights reserved.
Package Contents
Open the shipping carton of the Switch and carefully unpack its contents. The carton
should contain the following items:
One DGS-363 -28SC switch
One AC power cord
One console cable (RJ-45 to RS-232)
One console cable (USB to mini-USB)
One rack mounting kit (two brackets and screws)
Four rubber feet with adhesive backing
One power cord retainer set
One Quick Installation Guide
One CD
Installation Guidelines
This section will discuss the hardware installation guidelines that the user must follow in
order to properly and safely install this switch into the appropriate environment.
Visually inspect the power cord and see that it is fully secured to both the power
connector, on the Switch, and the electrical outlet that supplies power.
Install the Switch in a fairly cool and dry place within the acceptable operating
temperature and humidity ranges.
Install the Switch in a site free from strong electromagnetic field generators such as
motors, vibration, dust, and direct exposure to sunlight.
Installing the Switch without a Rack
This section is used to guide the user through installing the Switch in an area other than a
switch rack. Attach the included rubber feet to the bottom of the Switch. Take note that
there should be marked blocks on the bottom of the Switch to indicate where to attach the
rubber feet. These markings are usually found in each corner on the bottom of the device.
The rubber feet cushion the Switch, protecting the casing from scratches and preventing it
from scratching other surfaces.
Figure 1 — Attaching rubber feet to the Switch
2

Install the Switch on a sturdy, level surface that can support the weight of the Switch. Do
not place any heavy objects on the Switch. The power outlet should be within 1.82 meters
(6 feet) of the Switch. Make sure that there is proper heat dissipation from and adequate
ventilation around the Switch. Leave at least 1 cm (4 inches) of space at the front, sides,
and rear of the Switch for ventilation.
Installing the Switch in a Standard 19'' Rack
This section is used to guide the user through installing the Switch into a switch rack. The
Switch can be mounted in a standard 19"(1U) rack using the provided mounting brackets.
Fasten the mounting brackets to the sides of the Switch using the screws provided.
Figure 2 — Attaching rack- ount brackets to the Switch
Fasten the mounting brackets in any available open space in the rack using the screws
provided.
Figure 3 — Installing the Switch in a Rack
Installing Transceivers into the Transceiver Ports
The Switch is equipped with Small Form-factor Pluggable (SFP) and Enhanced Small
Form-factor Pluggable (SFP+) ports that can be used to connect various other networking
devices to this switch that do not support the standard RJ-45 wiring connection. These
ports are generally used to connect this switch to optical fiber connections and can be
used to connect devices to the Switch over great distances. The maximum distance that
the RJ-45 wiring connection can reach is 1 meters. Fiber optic connections can span
several kilometers.
3

Figure 4 — Inserting transceivers into the transceiver ports
Power On (AC Power)
Plug one end of the AC power cord into the power socket of the Switch and the other end
into the local power source outlet. After the system is powered on, the LED will blink green
to indicate that the system is booting up.
Power Failure (AC Power)
In the event of a power failure, just as a precaution, unplug the power cord from the
Switch. After the power returns, plug the power cord back into the power socket of the
Switch.
Installing Power Cord Retainer
To prevent accidental removal of the AC power cord, it is recommended to install the
power cord retainer together with the power cord.
With the rough side facing down, insert the tie wrap into the hole below the power socket.
Figure 5 — Insert Tie Wrap into the Switch
4

Plug the AC power cord into the power socket of the Switch.
Figure 6 — Connect the power cord to the Switch
Slide the retainer through the tie wrap until the end of the cord.
Figure 7 — Slide the Retainer through the Tie Wrap
Circle the tie of the retainer around the power cord and into the locker of the retainer.
Figure 8 — Circle around the power cord
5

Fasten the tie of the retainer until the power cord is secured.
Figure 9 — Secure the power cord
Installing the Redundant Power Supply (RPS)
The Redundant Power Supply (RPS) is designed to conform to the wattage requirements
of D-Link’s Ethernet and Gigabit switches. It is an external RPS unit enclosed in solid
metal case with sockets to connect AC or DC power sources on one end, and to connect
to a switch’s internal power supply on the other end. The RPS provides a low-cost, simple
solution to the problem of an inadvertent failure of the internal power supply of an Ethernet
switch, which can result in the shutdown of that switch, the devices attached to its ports, or
an entire network.
CAUTION: Do not connect the RPS to AC power before the DC power cable is
connected. This might damage the internal power supply.
CAUTION: Leave at least 15 cm (6 inches) of space at the rear of the Switch when
an RPS is installed to prevent cable damage.
DPS-500A and DPS-500DC Redundant Power Supplies
This RPS (DPS-5 A and DPS-5 DC) can be connected to the Switch’s RPS port using
a 14-pin DC power cable. A standard, three-pronged AC power cable connects the RPS to
the main power source.
6

Figure 10 — Connecting a DGS-3630 Series Switch to the DPS-500A
Installing the RPS into a Rack-mount Chassis
DPS-800
The DPS-8 is a standard-size (1 standard unit in height) rack-mountable unit designed
to hold up to two RPS units.
NOTE: This rack-mount chassis supports the following RPS units: DPS-5 A and
DPS-5 DC.
Figure 11 — Install the DPS-500A in the DPS-800
7

Figure 12 — Install the DPS-800 in an Equip ent Rack
Management Options
This switch provides multiple access platforms that can be used to configure, manage, and
monitor networking features available on this switch. Currently there are three
management platforms available which are described below.
Co and Line Interface (CLI)
This switch can be managed, out-of-band, by using the console port or the MGMT port on
the front panel of the Switch. Alternatively, the Switch can also be managed, in-band, by
using a Telnet connection to any of the LAN ports on the Switch. The command line
interface provides complete access to all switch management features.
SNMP-based Manage ent
The Switch can be managed with an SNMP-compatible console program. The Switch
supports SNMP v1, SNMPv2c and SNMPv3.
Web User Interface (Web UI)
The Web UI can be accessed from any computer running web browsing software from its
MGMT port, or LAN port when it is connected to any of the RJ-45 or SFP/SFP+ ports. The
Web UI on the Switch can also be accessed using an HTTPS (SSL) connection. This
management interface is a more graphical representation of the features that can be
viewed and configured on this Switch. Most of the features available through the CLI can
be accessed through the Web UI. Web browsers like Microsoft’s Internet Explorer, Mozilla
Firefox, or Google Chrome can be used.
Connecting to the Console Port
The front panel of the Switch provides an RJ-45 and a mini-USB console port to connect a
8

remote system for monitoring and configuring the Switch. Both ports require their
respective cables included with the Switch, to establish the physical connection.
NOTE: When an active console connection is made to both the RJ-45 console port
and the mini-USB console port at the same time, the mini-USB console port will
have higher priority.
Connecting to the RJ-45 Console Port
To use the RJ-45 console port, the following equipment is needed:
A terminal or a computer with both an RS-232 serial port and terminal emulation
software
A console cable with a male DB9 connector on one end and an RJ-45 connection
on the other
To connect the RJ-45 console port on the Switch to the computer:
Connect the male DB9 connector on the console cable (shipped with the Switch) to
the RS-232 serial port on the computer running terminal emulation software then
insert the RJ-45 connector into the RJ-45 console port on the front of the Switch.
To configure the terminal emulation software as follows:
Select the appropriate serial port (COM1 or COM2).
Set the data rate to 1152 baud.
Set the data format to 8 data bits, 1 stop bit, and no parity.
Set flow control to none.
Figure 13 — COM Port Configuration
To be able to view the boot procedure, the Switch needs to be rebooted. The simplest way,
at this stage, to reboot the Switch is to unplug and re-insert the power cable from and into
the power receptacle on the back of the Switch. After correctly configuring the terminal
settings and re-inserting the power cable, the boot procedure will appear in the terminal.
9

After the boot sequence has been completed, the console login screen will be displayed.
Connecting to the ini-USB Console Port
To use the mini-USB console port, the following equipment is needed:
A terminal or a computer with a USB 2. port and the ability to emulate a terminal
A console cable with a 5-pin mini-B male connector on one end and a USB Type A
male connecter on the other
Software to emulate a virtual COM port to be used in the terminal emulation
software (this software can be found on the CD included in this package and can
only be used on a Microsoft® Windows operating system)
To connect the mini-USB console port on the Switch to the computer:
1. Install the software to emulate a virtual COM port on the computer.
2. Connect the USB Type A male connecter on the console cable (shipped with the Switch)
to the USB port on the computer, then insert the mini-B male connector into the mini-USB
console port on the front of the Switch.
Figure 14 — Connect ini-USB Console Port
3. Check the serial port number in Device Manager. The name of the virtual COM port is
Prolific USB-to-Serial Co Port.
10