D-Link DGS-6600-48TS User manual

This document will guide you through the basic
installation process for your new D-Link
chassis-based Switch.
Building Networks for People
DGS-6600 Series
Documentation also available on CD
and D-Link Website
Quick Installation Guide
4 Slot Chassis-Based Switch

2 u D-Link DGS-6604 Modular Switch
ENGLISH
About This Guide
This guide contains step by step instructions
for setting up the D-Link DGS-6604 chassis-
based switch. Please note that the model you
have purchased may appear slightly different
from those shown in the illustrations.
Please read this manual carefully before using
the product, paying special attention to safety
warnings so as to avoid injury or damage to
equipment.
This manual is intended for users who have
experience in installing and maintaining
network hardware, and assumes that users
are familiar with standard networking terms
and concepts.
Product Overview
D-Link’s DGS-6604 chassis-based switch is
an intelligent and high-performance multi-layer
LAN device designed for enterprise campus
and metropolitan area networks (MAN). It is
ideal for deployment in environments where
uninterrupted network applications and a high
level of performance, security and control are
required.
Featuring exible modular architecture and
industry standard compliance, the switch
provides scalable expansion and a high
level of investment protection for businesses
and telecom carriers to deploy Gigabit and
10-Gigabit packet switching and routing for
ofce networking and Ethernet-based Internet
services to homes.
Warning s
Power Supply Safety Warning
Ground the device before power-
ing on to guard against power
surges.
Be sure that all cables are ground-
ed correctly.
Static Electricity Protection
Warning
Always wear an anti-static wrist
strap when contacting the chassis
to prevent static damage.
Laser Safety Warning
CLASS 1 LASER PRODUCT
Directly looking at the optical in-
terface or optical bers may cause
eye damage.
Fan Safety Warning
The fan mechanism is dangerous.
Avoid touching the area near the
fan.
Transportation Safety Warming
The device and components may
comprise more than 27 kg in total.
Use care when inserting or remov-
ing heaving components.
Maintenance Warning
Maintenance should only be car-
ried out by qualied service techni-
cians

D-Link DGS-6604 Modular Switch u 3
ENGLISH
Preparation for Installation
To ensure normal operation and prolonged life
of the DGS-6604, the appropriate temperature
and humidity must be maintained in the equip-
ment room.
If the equipment room’s temperature and
humidity do not meet the requirements. the
equipment may sustain damage.
Operating Temperature Operating Humidity
0ºC-50ºC 10%-90% RH
non-condensed
Table 1. Temperature and Humidity
Requirements
Notes:
1. The ambient temperature and
humidity should be measured
at the point that is 1.5m above
the oor and 0.4m in front of the
equipment when there is no pro-
tective plate in front or back of the
equipment rack
2. The short-term working condi-
tions apply where the continuous
working period does not exceed 48
hours and the cumulative total pe-
riod within a year does not exceed
15 days
Static Discharge Damage Prevention
To prevent damage from static electricity,
please conform to the following guidelines:
1. Be sure to install an adequate ground for
all electronic equipment.
2. Use appropriate dust prevention measures.
3. Maintain the required humidity in the oper-
ating environment
4. Always wear an anti-static wrist strap when
working around any electronic circuitry.
5. Hold a circuit board by its edges. Do not
touch any components on the PCB.
6. Do not allow clothing to touch a circuit
board. An antistatic wrist strap can only
prevent static electricity from the human
body, but cannot mitigate static electricity
from clothing.
Moving the Device
The DGS-6604 is quite heavy. When handling,
please pay close attention to the following
guidelines:
• Avoid moving the equipment frequently.
• If you nd the chassis weight unbearable,
do not attempt to lift the equipment alone.
• Lift and move the chassis using the han-
dles on the top panel .
• Turn off all power supplies and unplug all
power cables before moving the equip ment.
• Completely loosen the thumb/Phillips
screws and pull the card levers to remove
each and all line cards, fan tray, and power
mod ules from the chassis before moving it.
Figure 1. Correctly Moving the DGS-6604
Do not move the equipment by
grasping the panels, power sup-
ply handles, or ventilation holes,
as they are not designed to bear
weight.

4 u D-Link DGS-6604 Modular Switch
ENGLISH
System Grounding Requirements:
Proper grounding will help to ensure stable
and reliable operation of the DGS-6604. Be
sure to verify that the grounding conditions
at the installation meet the grounding
requirements and ground all devices
appropriately.
Ground Connection
Power Requirements
The power consumption and heat dissipation
gures of the various DGS-6604 components are
listed in the table below:
DGS-6600 Series
Module
Maximum
Power
Consumption
(W)
Heat
Dissipation
(BTU/Hour)
DGS-6600-CM 54 184
DGS-6600-48T 110 375
DGS-6600-48S 119 405
DGS-6600-48TS 114 390
DGS-6600-48P 873 2979
DGS-6600-8XG 200 684
DGS-6600-24SC2XS 106 360
DGS-6600-FAN
Fan Tray
43 144
DGS-6600-PWR
AC Power Supply
854
(@110VAC
or 220 VAC)
2913
(@110VAC
or 220 VAC)
Figure 2. Grounding of the DGS-6604
Note:
All grounding conductors should
be connected before the AC power
is applied to the DGS-6604 in-
stalled AC power supplies.
The DGS-6604 with AC power
supplies must be grounded with
a minimum of 0.823 mm2 (or
18AWG) of conductive ground-
ing cable. This cable is connected
between the Equipment Room
Ground and the DGS-6604 Chas-
sis Ground Terminal.
Table 2. Card Power Requirements
Note:
The DGS-6604 provides either
1+1, 2+1, or 3+1 redundant AC
power supplies. D-Link
recommends to use multiple
power supplies for the equipment
to ensure continuous and stable
operation. Redundant power
supplies help to prevent
unexpected power failures.
Redundant power supplies must
be identical.

D-Link DGS-6604 Modular Switch u 5
ENGLISH
Installation Tools Requirements
Type Tools Remarks
Common
Tools
Claw hammer,
pliers
Unpack wooden
case and
transportation case.
Phillips-head
screwdriver,
straight
screwdriver,
spanner
Disassemble
chassis, power
supply, fan and
modules
Power supply
cables,
network
cables, optical
bers and
distribution
cables
Connect the
interfaces.
Ruler, long
tapeline,
marker pen
Measure the
installation position.
Bolts, diagonal
pliers, straps
Mount the chassis.
Special
purpose
tools
Anti-static tool Prevent static
electricity.
Wire stripper,
crimping pliers
Create network
cables and
grounding cables.
Meter Multimeter Test power supply
and DC resistance.
500V
Megohm-
meter
Test the insulation
and grounding
resistance
Table 3. Required Tools
Installation Site
Requirements
The DGS-6604 must be used indoors. To
ensure the normal operation and prolonged
useful life of the equipment, the installation
site must meet the following requirements.
Requirements for Rack Mounting
If you plan to mount the DGS-6604 in a frame,
please observe the following guidelines:
• Install the switch in an open cabinet if
pos sible. If you install the switch inside
a closed cabinet please ensure that the
cabi net has a good ventilation and heat
dissipation system.
• Ensure that the cabinet is durable enough
to bear the weight of the DGS-6604 and its
installation accessories.
• Ensure that the dimensions of the cabinet
provide enough space for the installation
of the front, rear, left and right panels of
the DGS-6604 for the purpose of heat
dissipation.
• The frame should be properly grounded.
Ventilation Requirements
Following gure shows the ventilation
requirements of the DGS-6604. You must
reserve sufcient space near the vents to
ensure proper ventilation. After the cables
have been connected, they should be
arranged into bundles or placed on the cabling
rack to prevent the obstruction of air intakes
and vents.
Figure 3. Ventilation of the DGS-6604
Mounting the DGS-6604 into the Cabinet
1. Lift the chassis (seek assistance if the
chassis is more then you can lift safely)
while keeping it level Slowly move it to the
front of the frame.
2. Keeping the DGS-6604 level, lift it to a
posi tion slightly higher than the tray of the
slide rail of the cabinet. Set the chassis
onto the tray or the slide rail, and push it
into the cabinet.
3. Fasten the DGS-6604 to the cabinet with
screws. Fastening notches are on both the
left and right sides of the front panel on the

6 u D-Link DGS-6604 Modular Switch
ENGLISH
equipment frame. Use screws to fasten
them to the bracket of the cabinet/ Once
fastened, the equipment should be stable
and immobile.
Installing the Fan Tray
The DGS-6600-FAN fan tray is used as the
DGS-6604’s ventilation system. Carry out the
following to install the fan tray:
1. Use the thumb-screws to remove the fan
tray blank panel.
2. Insert the fan tray into the guide rail of the
fan tray slot.
3. Secure the fan tray by tightening the fan
tray’s captive-screws.
Figure 4. Installing the Fan Tray
Installing the Power Supply(s)
The DGS-6604 switch is powered up using an
AC power supply. The procedure for installing
the AC power supply is shown in the diagram
below:
Figure 5. Installing the Power Supply
Connecting the System Ground
A working ground GND is installed on the back
of DGS-6604. GND should be directly
connected to the ground bar of the equipment
room. If a digital grounding bar and an analog
grounding bar exist in the equipment room, the
GND should be connected to the digital bar.
Ground Connection
Figure 6. Ground Connections on the back of the
DGS-6604
Precautions.
The sectional area of the grounding cable
(min. of 18AWG) should be selected to safely
conduct the maximum possible current. Use
insulated cables of good conductivity.
• Do not use bare wire.
• The grounding resistance for combined
grounding should be less than 1 Ohm (Ω).
Simple Grounding Steps
• Unfasten the nut on the rear grounding
post of the equipment.
• Afx the terminal of the grounding cable to
the grounding pole.
• Fasten the nut back on the grounding post.
• Connect the other end of the grounding
cable to a suitable grounding bar.

D-Link DGS-6604 Modular Switch u 7
ENGLISH
Installing the Air Filter of the DGS-6604
On the back of the chassis on the edge of the
right-side is a vertical slot where the air lter
can be tted. Slide in a cleaned or new air lter
into the slot as per the following diagram. Then
screw the two thumb/Phillips screws (see the
diagram arrows) to secure the air lter into the
chassis. With the air lter installed screw-in two
screws on the side of the chassis as indicted
by the red arrows in the diagram.
Figure 7. Installing the Air Filter
Air lter installation is recommend-
ed as the last step of the chassis
installation.
Connecting the AC Power Supply to the
Power Module
Use the related AC power cable to connect to
the AC power module panel, as indicated in
the following diagram:
Figure 8. Connecting AC to the Power Module
AC Power Supply Connection Precaution
• Verify that the provided external power
sup ply matches the power module installed
in the Switch before connecting the power
supply.
• Use a power cable with a standard 3-pin
connector to make the power connection.
• Ensure that the connected power cables
have good contacts.
• Once the power cable is plugged-in at both
power outlet and the power supply, the
power supply will immediately start.
Simple AC Power Connection Steps
1. Insert the power cable’s plug into the
power module.
2. Secure the power cable to the cable clip on
the right.
3. Connect the other end of the power cable
into the corresponding socket or connector.

8 u D-Link DGS-6604 Modular Switch
ENGLISH
Connecting the Serial Cable of the Man-
agement Module
Simple CPU Module Cable Connection
1. Connect the RJ45 connector of an Ethernet
cable to the Ethernet port of the Switch’s
management module (DGS-6600-CM) and
connect the other end of the cable to any
TCP/IP capable device that is able to exe-
cute Telnet or SSH.
- or -
2. Connect the standard DB9 end of the
serial cable to the RS-232 serial port of
the Switch’s management module and the
other end to the PC/Notebook or control
terminal.
- or -
3. Connect a USB cable with a USB Standard
B Connector to the Standard B receptacle
on the Switch’s management module. Con-
nect the other end to a computer equipped
with a USB port capable of supporting a
serial interface using the PL-2303 USB
Serial Driver SW from Prolic Technology
Inc..
Removing Boards from the DGS-6604
Carry out the following steps to remove boards
from the DGS-6604:
1. Unplug all copper/ber cabling, i.e. RJ45
twisted-pair and ber optic cables, from the
board to be removed.
2. Loosen and unscrew the panel’s two cap-
tive screws.
3. Use both hands to pull the levers, on the
left and right hand sides of the board, to
remove the board from the DGS-6604, as
shown in the following diagram.
Caution
Before removing/adding a board,
always wear an anti-static wrist
strap.
Take care not to hold the edge of
the PCB or collide the components
of the PCB..
Figure 9. Removing a board from the chassis
Installing Boards on the DGS-6604
Carry out the following steps to install boards
in the DGS-6604:
1. Remove the component card or blank panel
as instructed in the section.
2. Insert the new board into the guide rail of
the vacant slot.
3. Use the levers on the left and right hand
side to push the board into position and
tighten the two captive screws on the board
using a straight screw driver.
Caution
1. Take care not to hold the
edge of the PCB or collide the
compo nents of the PCB.
2. Always use the levers to plug/
unplug a PCB module. Never
use force to remove a PCB
module.

D-Link DGS-6604 Modular Switch u 9
ENGLISH
Figure 10. Installation Check
Installation Check
Verify that the external AC power supply
provides the correct voltage and frequency.
Verify that the cabinet has been fastened
completely, and does not move or tilt.
Verify that the Power Supplies, CM and Line
Cards have been installed in the chassis.
Verify that the optical ber and twisted pair
cables match their respective interfaces.
Verify that the cables have been bound
appropriately and are not subject to any
excess stress.
Verify that the power cables are in good
condition and comply with safety requirements.
Verify that the power module has been rmly
installed into the backplane connector.
Turn on the power switch and verify that the
power module is operating correctly.
Unpacking Inspection
Requirements
Checklist
1. DGS-6604 Chassis Carton
• DGS-6604 Chassis (no cards installed)
1. Card Module Carton (s)
• 1 CM Card DGS-6600-CM
• Line Cards (specic per order)
• Power Supplies Units (number specic per
order)
2. DGS-6604 Accessories Carton including:
• AC Power Cord
• RS-232 Console Cable (9 pin D-Sub)
• USB Console Cable (Type A to Type B)
• Fan Tray
• Air Filter
• CD software and manual
• QIG
Management Options
The system may be managed out-of-band
through the console port(s) and Ethernet port
on the Control Module or in-band using Telnet/
SSH. Each Switch must be assigned its own IP
address, which is used for communication with
an SNMP network manager or other TCP/IP
application (for example BOOTP, TFTP). The
Switch’s default IP address is 10.90.90.90 (out-
of-band IP address). The user can change the
default IP address to meet the specications of
your networking address scheme.
Connecting the Console Port (USB or 9
Pin D-Sub)
The switch provides a USB or 9 Pin D-Sub
Serial Connection to a computer or terminal
for monitoring and conguration. To use
the console port, you need the following
equipment:
• A terminal or a computer with a 9 pin serial
port /USB port and the ability to emulate a
terminal.
• A null modem or cross-over RS-232 cable
with a female DB-9 connector for the
switch’s console port.
- or -

10 u D-Link DGS-6604 Modular Switch
ENGLISH
• A USB cable (with a Type B USB connector
for the switch’s USB console port) and the
Serial USB driver installed on the computer
used to connect to the console.
Download the USB-Serial Driver here:
http://www.prolic.com.tw/eng/
downloads.asp?ID=31
Conrm the driver for your Operating
System is for the X chip series.
To connect a terminal to the console port
1. Connect the supplied RJ-45-to DB-9 adapt-
er cable to the standard 9-pin serial port on
the PC. Connect the other end of the cable
to the console port on the switch. Set the
terminal emulation software as fol lows:
• Baud rate: 115200
• Data bits: 8
• Parity: None
• Stop bits: 1
• Flow control: None
2. Select VT100 for the terminal emulation
mode.
3. After you have correctly set up the terminal,
plug the power cable into the power sup-
plies on the switch. The boot sequence will
appear in the terminal.
4. Press the Enter key at the password
prompts. There is no default password for
the Switch.
5. Enter the commands to complete your de-
sired tasks. Many commands require ad-
ministrator-level access privileges. See the
CLI Reference Guide on the documen tation
CD for a list of all commands and additional
information using the CLI.
Telnet Management Users may also access
the switch CLI by using PC’s Command Prompt.
To access it from your computer, users must rst
ensure that a valid connection is made through
the Ethernet port of the Switch and your PC,
and then click Start > Programs > Accessories >
Command Prompt on your computer. Once the
console window opens, enter the command
telnet 10.90.90.90 (depending on congured
IP address) and press Enter on your keyboard.
You should be directed to the opening console
screen for the CLI of the switch, press the En-
ter key at the password prompts. There is no
default password for the Switch.
SNMP-Based Management
You can manage the Switch with D-Link
D-View or any SNMP-compatible console
program. The SNMP function is disabled by
default for D-Link managed switches.
Additional Information
If you are encountering problems setting up
your network, please refer to the User’s Guide
that comes with the switch. It contains many
more rules, charts, explanations and examples
to help you get your network up and running.
Additional help is available through our of-
ces listed online. To learn more about D-Link
products or marketing information, please visit
the website http://www.dlink.com, which will
re-direct you to your appropriate local D-Link
website.
Technical Support
United Kingdom (Mon-Fri)
website: http://www.dlink.co.uk
FTP: ftp://ftp.dlink.co.uk
Home Wireless/Broadband 0871 873 3000
(9.00am–06.00pm, Sat 10.00am-02.00pm)
Managed, Smart, & Wireless Switches, or
Firewalls 0871 873 0909 (09.00am- 05.30pm)
(BT 10ppm, other carriers may vary.)
Ireland (Mon-Fri)
All Products 1890 886 899 (09.00am-06.00pm,
Sat 10.00am-02.00pm)
Phone rates: €0.05ppm peak, €0.045ppm off
peak times