D-Link DGS-F1026P-E User manual

Product Quick Installation Guide
DGS-F1026P-E
26-Port Gigabit Switch with Long Reach PoE+ and 2 SFP Ports

1.1 Package Contents
The package contains the following items:
•PoE Switch
•Power Cord
•19”Rack Mounting Kit
•Quick Installation Guide
1.2 Safety Instructions
Use the following safety guidelines to ensure your own personal safety and to help protect
your equipment from potential damage.
•The power cable should be disconnected from the mains during the installation process;
•Wear a grounded anti-static wrist band to avoid the build-up of static electricity;
•Power the product only from the type of external power source indicated on the electrical ratings
label.
•Observe extension cable and power strip ratings. Make sure that the total ampere rating of all
products plugged into the extension cable or power strip does not exceed 80 percent of the ampere
ratings limit for the extension cable or power strip;
To avoid the risk of electric shock, do not open the switch housing.
•Do not use damaged power cords. Do not modify power cables or plugs.
1.3 Connecting Power
Connect one end of the power cord to the rear of the switch, and the other end to the mains power
outlet.

1.4 Product Connection Diagram
1.5 Product Installation
The DGS-F1026P-E switch can be installed on a desktop, shelf or mounted in a standard 19-inch rack. To
install the switch in a rack, attach the supplied mounting brackets to the side of the switch and fasten the
brackets to the sides of the switch using the screws from the switch mounting kit.

Align the brackets and rack holes. Fasten each bracket to the rack.
1.6 Product Ports Description
Port
Description
PoE 1-24
PoE Port: Support IEEE802.3af/at standard Power over Ethernet, used
to connect PD devices;
Ports 1 –8 PoE support cable lengths up to 250m @ 10Mbps (“Extend”
mode enabled);
Ports 9 –24 PoE, support cable lengths up to 100m.
Uplink
SFP port: use suitable transceiver to expand network, connect NVR, PC,
aggregation switch, etc.
AC power input
Connect power cord to the mains power outlet.

1.7 Product Specifications
Switch Modes
Extend: Supports long reach PoE delivery, up to 250m.
(Cat 5 or better cabling is recommended)
VLAN: Isolates ports from each other. Adds security and improves network
performance by constraining broadcast traffic.
QOS: Introduces application prioritisation. Traffic with higher priority (e.g. Voice
over IP) will be forwarded ahead of the queue.
PoE: Automatically restarts a remote device by disabling and re-enabling PoE on
the port if it detects the remote device has locked up (no incoming traffic).
Network Port
24 x 10/100Mbps/1000Mbps PoE RJ45 ports (Port 1 –Port 24)
2 SFP uplink
Transfer Rate
1000Mbps full Duplex, 10 or 100 or 1000Mbps Half Duplex (Downlink)
Network Protocol
standards
IEEE 802.3i, IEEE 802.3u, IEEE 802.3x, IEEE 802.3ab, IEEE 802.3z, IEEE 802.3az, IEEE
802.3af, IEEE 802.3at
Performance
Bandwidth: 52 Gbps (non-blocking)
Network delay（1000 to 100Mbps): maximum 10μs (using 64-byte packet)
Frame filtering and transmission rate:
10M port maximum 14,800pps
100M port maximum 148,800pps
1000M port maximum 148,8800pps
LED indicator
Power
RESV
LINK/ACT
PoE pins
1/2(+), 3/6(-)
Power
Max power for single port 30 W
Total Power Budget: 250 W
Dimensions
Size（L x W x H): 440mm x 180mm x 44mm
Weight: 3.0 kg
Environment
Operating Temperature: 0°- 40°C
Operating Humidity: 10% - 90%, Non-condensing
Safety
CE/ROHS/FCC