D-Link xStack DGS-3120 Series Instruction Manual

xStack® DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
I
Table of Contents
Chapter 1 Using Command Line Interface ....................................................................................................1
Chapter 2 Basic Command List.....................................................................................................................8
Chapter 3 802.1Q VLAN Command List .....................................................................................................23
Chapter 4 802.1X Command List ................................................................................................................38
Chapter 5 Access Authentication Control Command List............................................................................62
Chapter 6 Access Control List (ACL) Command List ................................................................................103
Chapter 7 Access Control List (ACL) Egress Command List (RI and EI Mode Only)...............................123
Chapter 8 Address Resolution Protocol (ARP) Command List .................................................................142
Chapter 9 ARP Spoofing Prevention Command List.................................................................................147
Chapter 10 Asymmetric VLAN Command List ............................................................................................149
Chapter 11 Auto-Configuration Command List............................................................................................151
Chapter 12 Basic Commands Command List .............................................................................................153
Chapter 13 BPDU Attack Protection Command List ...................................................................................171
Chapter 14 Cable Diagnostics Command List.............................................................................................176
Chapter 15 Command Logging Command List ...........................................................................................179
Chapter 16 Compound Authentication Command List................................................................................182
Chapter 17 Configuration Command List ....................................................................................................193
Chapter 18 Configuration Trap Command List............................................................................................198
Chapter 19 Connectivity Fault Management (CFM) Command List (RI and EI Mode Only).......................200
Chapter 20 Connectivity Fault Management (CFM) Extension Command List (RI and EI Mode Only)......228
Chapter 21 CPU Interface Filtering Command List .....................................................................................232
Chapter 22 Debug Software Command List................................................................................................243
Chapter 23 Denial-of-Service (DoS) Attack Prevention Command List ......................................................286
Chapter 24 DHCP Local Relay Command List............................................................................................290
Chapter 25 DHCP Relay Command List .....................................................................................................294
Chapter 26 DHCP Server Command List (RI Mode Only) ..........................................................................318
Chapter 27 DHCP Server Screening Command List...................................................................................337
Chapter 28 DHCPv6 Relay Command List .................................................................................................349
Chapter 29 Digital Diagnostic Monitoring (DDM) Command List (RI and EI Mode Only)...........................359
Chapter 30 Distance Vector Multicast Routing Protocol (DVMRP) Command List (RI Mode Only)...........366
Chapter 31 Domain Name System (DNS) Resolver Command List ...........................................................373
Chapter 32 D-Link License management System (DLMS) Command List.................................................380
Chapter 33 D-Link Unidirectional Link Detection (DULD) Command List (RI and EI Mode Only)..............382
Chapter 34 Energy Efficient Ethernet (EEE) Command List.......................................................................384

xStack® DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
II
Chapter 35 Ethernet Ring Protection Switching (ERPS) Command List (RI and EI Mode Only)................386
Chapter 36 FDB Command List...................................................................................................................396
Chapter 37 Filter Command List..................................................................................................................406
Chapter 38 Flash File System (FFS) Command List...................................................................................409
Chapter 39 Gratuitous ARP Command List.................................................................................................420
Chapter 40 Internet Group Management Protocol (IGMP) Command List (RI Mode Only)........................426
Chapter 41 IGMP Proxy Command List (RI Mode Only).............................................................................434
Chapter 42 IGMP Snooping Command List ................................................................................................439
Chapter 43 IP-MAC-Port Binding (IMPB) Command List (RI and EI Mode Only).......................................463
Chapter 44 IP Multicast (IPMC) Command List (RI Mode Only).................................................................490
Chapter 45 IP Route Filter Command List (RI Mode Only).........................................................................492
Chapter 46 IP Tunnel Command List (RI Mode Only).................................................................................499
Chapter 47 IPv6 Neighbor Discover Command List....................................................................................507
Chapter 48 IPv6 Route Command List........................................................................................................514
Chapter 49 Japanese Web-Based Access Control (JWAC) Command List...............................................517
Chapter 50 Jumbo Frame Command List ...................................................................................................541
Chapter 51 Layer 2 Protocol Tunneling (L2PT) Command List ..................................................................543
Chapter 52 Link Aggregation Command List...............................................................................................547
Chapter 53 Link Layer Discovery Protocol (LLDP) Command List .............................................................554
Chapter 54 Loopback Detection (LBD) Command List ...............................................................................580
Chapter 55 Loopback Interface Command List (RI Mode Only) .................................................................586
Chapter 56 MAC Notification Command List...............................................................................................589
Chapter 57 MAC-based Access Control Command List .............................................................................594
Chapter 58 MAC-based VLAN Command List ............................................................................................611
Chapter 59 MD5 Configuration Command List (RI Mode Only)..................................................................614
Chapter 60 Mirror Command List ................................................................................................................617
Chapter 61 Multicast Listener Discovery Protocol (MLD) Command List (RI Mode Only)..........................623
Chapter 62 MLD Proxy Command List (RI Mode Only) ..............................................................................626
Chapter 63 MLD Snooping Command List..................................................................................................631
Chapter 64 MSTP debug enhancement Command List..............................................................................652
Chapter 65 Multicast Filter Command List...................................................................................................659
Chapter 66 Multicast VLAN Command List.................................................................................................670
Chapter 67 Network Load Balancing (NLB) Command List........................................................................684
Chapter 68 Network Monitoring Command List...........................................................................................690
Chapter 69 OAM Command List (RI and EI Mode Only).............................................................................696
Chapter 70 Open Shortest Path First (OSPF) Version 2 Command List (RI Mode Only)...........................704

xStack® DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
III
Chapter 71 OSPF Version 3 Command List (RI Mode Only)......................................................................725
Chapter 72 Password Recovery Command List..........................................................................................744
Chapter 73 Peripherals Command List........................................................................................................747
Chapter 74 Ping Command List...................................................................................................................754
Chapter 75 Policy Route Command List (RI Mode Only)............................................................................757
Chapter 76 Port Security Command List.....................................................................................................760
Chapter 77 Power over Ethernet (PoE) Command List (DGS-3120-24PC and DGS-3120-48PC Only)
768
Chapter 78 Power Saving Command List ...................................................................................................774
Chapter 79 PPPoE Circuit ID Insertions Command List (RI and EI Mode Only) ........................................780
Chapter 80 Protocol Independent Multicast (PIM) Command List (RI Mode Only).....................................784
Chapter 81 PIM for IPv6 Command List (RI Mode Only) ............................................................................802
Chapter 82 Protocol VLAN Command List..................................................................................................821
Chapter 83 QinQ Command List (RI and EI Mode Only) ............................................................................827
Chapter 84 Quality of Service (QoS) Command List...................................................................................835
Chapter 85 Reboot Schedule Command List..............................................................................................852
Chapter 86 Remote Switched Port ANalyzer (RSPAN) Command List ......................................................855
Chapter 87 Routing Information Protocol (RIP) Command List (RI Mode Only).........................................861
Chapter 88 RIPng Command List (RI Mode Only)......................................................................................866
Chapter 89 Routing Command List .............................................................................................................872
Chapter 90 RPC PortMapper Command List ..............................................................................................888
Chapter 91 Safeguard Engine Command List.............................................................................................890
Chapter 92 SD Card Management Command List......................................................................................892
Chapter 93 Secure File Transfer Protocol (SFTP) Command List..............................................................899
Chapter 94 Secure Shell (SSH) Command List ..........................................................................................902
Chapter 95 Secure Sockets Layer (SSL) Command List............................................................................915
Chapter 96 Spanning Tree Protocol (STP) Command List .........................................................................922
Chapter 97 Surveillance VLAN Command List............................................................................................935
Chapter 98 sFlow Command List (RI and EI Mode Only) ...........................................................................941
Chapter 99 Show Technical Support Command List...................................................................................953
Chapter 100 Simple Mail Transfer Protocol (SMTP) Command List.............................................................956
Chapter 101 Simple Network Management Protocol (SNMP) Command List..............................................961
Chapter 102 Single IP Management Command List.....................................................................................990
Chapter 103 Stacking Command List (EI and SI Mode Only).....................................................................1000
Chapter 104 Static Multicast Route Command List (RI Mode Only) ...........................................................1008
Chapter 105 Syslog and Trap Source-interface Command List..................................................................1011

xStack® DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
IV
Chapter 106 System Log Command List.....................................................................................................1015
Chapter 107 System Severity Command List..............................................................................................1027
Chapter 108 Telnet Client Command List....................................................................................................1029
Chapter 109 TFTP Client Command List.....................................................................................................1030
Chapter 110 Time and SNTP Command List..............................................................................................1035
Chapter 111 Trace Route Command List....................................................................................................1043
Chapter 112 Traffic Control Command List.................................................................................................1046
Chapter 113 Traffic Segmentation Command List ......................................................................................1052
Chapter 114 Trusted Host Command List...................................................................................................1054
Chapter 115 UDP Helper Command List.....................................................................................................1058
Chapter 116 Virtual Router Redundancy Protocol (VRRP) Command List (RI Mode Only).......................1063
Chapter 117 VLAN Counter Command List (RI and EI Mode Only) ...........................................................1071
Chapter 118 VLAN Trunking Command List ...............................................................................................1076
Chapter 119 Voice VLAN Command List ....................................................................................................1081
Chapter 120 Web-Based Access Control (WAC) Command List................................................................1092
Chapter 121 Weighted Random Early Detection (WRED) Command List..................................................1108
Appendix A Password Recovery Procedure ..............................................................................................1115
Appendix B System Log Entries.................................................................................................................1117
Appendix C Trap Log Entries .....................................................................................................................1132
Appendix D RADIUS Attributes Assignment ..............................................................................................1141
Appendix E IETF RADIUS Attributes Support............................................................................................1144

xStack® DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
1
Chapter 1 Using Command Line
Interface
The Switch can be managed through the Switch’s serial port, Telnet, SNMP or the Web-based
management agent. The Command Line Interface (CLI) can be used to configure and manage the
Switch via the serial port or Telnet interfaces.
This manual provides a reference for all of the commands contained in the CLI. Every command
will be introduced in terms of purpose, format, description, parameters, and examples.
Configuration and management of the Switch via the Web-based management agent are
discussed in the Web UI Reference Guide. For detailed information on installing hardware please
also refer to the Hardware Installation Guide.
1-1 Accessing the Switch via the Serial Port
The Switch’s serial port’s default settings are as follows:
• 115200 baud
• no parity
• 8 data bits
• 1 stop bit
A computer running a terminal emulation program capable of emulating a VT-100 terminal and a
serial port configured as above are then connected to the Switch’s Console port via an included
RS-232 to RJ-45 convertor cable.
With the serial port properly connected to a management computer, the following screen should be
visible.
DGS-3120-24TC Gigabit Ethernet Switch
Command Line Interface
Firmware: Build 4.00.015
Copyright(C) 2014 D-Link Corporation. All rights reserved.
UserName:
PassWord:
DGS-3120-24TC:admin#
There is no initial username or password. Just press the Enter key twice to display the CLI input
cursor −DGS-3120-24TC:admin# .This is the command line where all commands are input.
NOTE: When Switches with different modes or different firmware versions are stacked together,
the following warning message will appear after the initial login:

xStack® DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
2
DGS-3120-24TC Gigabit Ethernet Switch
Command Line Interface
Firmware: Build 4.00.015
Copyright(C) 2014 D-Link Corporation. All rights reserved.
UserName:
PassWord:
WARNING: The stacking members are working on different firmware.
DGS-3120-24TC:admin#
1-2 Setting the Switch’s IP Address
Each Switch must be assigned its own IP Address, which is used for communication with an
SNMP network manager or other TCP/IP application (for example BOOTP, TFTP). The Switch’s
default IP address is 10.90.90.90. You can change the default Switch IP address to meet the
specification of your networking address scheme.
The Switch is also assigned a unique MAC address by the factory. This MAC address cannot be
changed, and can be found on the initial boot console screen – shown below.
Boot Procedure V3.00.501
-------------------------------------------------------------------------------
Power On Self Test ........................................ 100 %
MAC Address : 10-BF-48-D0-E0-E0
H/W Version : B1
Please Wait, Loading V4.00.015 Runtime Image .............. 100 %
UART init ................................................. 100 %
Starting runtime image
Device Discovery .......................................... |
The Switch’s MAC address can also be found in the Web management program on the Switch
Information (Basic Settings) window on the Configuration menu.
The IP address for the Switch must be set before it can be managed with the Web-based manager.
The Switch IP address can be automatically set using BOOTP or DHCP protocols, in which case
the actual address assigned to the Switch must be known.
Starting at the command line prompt, enter the commands config ipif System ipaddress
xxx.xxx.xxx.xxx/yyy.yyy.yyy.yyy. Where the x’s represent the IP address to be assigned to the
IP interface named System and the y’s represent the corresponding subnet mask.
Alternatively, you can enter config ipif System ipaddress xxx.xxx.xxx.xxx/z. Where the x’s
represent the IP address to be assigned to the IP interface named System and the zrepresents
the corresponding number of subnets in CIDR notation.

xStack® DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
3
The IP interface named System on the Switch can be assigned an IP address and subnet mask
which can then be used to connect a management station to the Switch’s Telnet or Web-based
management agent.
DGS-3120-24TC:admin# config ipif System ipaddress 10.24.22.100/255.0.0.0
Command: config ipif System ipaddress 10.24.22.100/8
Success.
DGS-3120-24TC:admin#
In the above example, the Switch was assigned an IP address of 10.24.22.100 with a subnet mask
of 255.0.0.0. The system message Success indicates that the command was executed
successfully. The Switch can now be configured and managed via Telnet, SNMP MIB browser and
the CLI or via the Web-based management agent using the above IP address to connect to the
Switch.
There are a number of helpful features included in the CLI. Entering the ?command will display a
list of all of the top-level commands.
DGS-3120-24TC:admin#?
Command: ?
..
?
cable_diag ports
cd
cfm linktrace
cfm lock md
cfm loopback
change drive
clear
clear address_binding dhcp_snoop binding_entry ports
clear address_binding nd_snoop binding_entry ports
clear arptable
clear attack_log
clear cfm pkt_cnt
clear counters
clear dhcp binding
clear dhcp conflict_ip
clear ethernet_oam ports
clear fdb
clear igmp_snooping statistics counter
clear jwac auth_state
clear log
CTRL+C ESC qQuit SPACE nNext Page ENTER Next Entry aAll
When entering a command without its required parameters, the CLI will prompt you with a Next
possible completions: message.

xStack® DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
4
DGS-3120-24TC:admin#config account
Command: config account
Next possible completions:
<username 15>
DGS-3120-24TC:admin#
In this case, the command config account was entered with the parameter <username 15>. The
CLI will then prompt to enter the <username 15> with the message, Next possible completions:.
Every command in the CLI has this feature, and complex commands have several layers of
parameter prompting.
In addition, after typing any given command plus one space, users can see all of the next possible
sub-commands, in sequential order, by repeatedly pressing the Tab key.
To re-enter the previous command at the command prompt, press the up arrow cursor key. The
previous command will appear at the command prompt.
DGS-3120-24TC:admin#config account
Command: config account
Next possible completions:
<username 15>
DGS-3120-24TC:admin#config account
In the above example, the command config account was entered without the required parameter
<username 15>, the CLI returned the Next possible completions: <username 15> prompt. The
up arrow cursor control key was pressed to re-enter the previous command (config account) at
the command prompt. Now the appropriate username can be entered and the config account
command re-executed.
All commands in the CLI function in this way. In addition, the syntax of the help prompts are the
same as presented in this manual −angle brackets < > indicate a numerical value or character
string, braces { } indicate optional parameters or a choice of parameters, and brackets [ ] indicate
required parameters.
If a command is entered that is unrecognized by the CLI, the top-level commands will be displayed
under the Available commands: prompt.

xStack® DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
5
DGS-3120-24TC:admin#the
Available commands:
.. ? cable_diag cd
cfm change clear config
copy create debug del
delete dir disable download
enable erase execute format
install login logout md
move no ping ping6
rd reboot reconfig rename
reset save show smtp
telnet traceroute traceroute6 upload
DGS-3120-24TC:admin#
The top-level commands consist of commands such as show or config. Most of these commands
require one or more parameters to narrow the top-level command. This is equivalent to show what?
or config what? Where the what? is the next parameter.
For example, entering the show command with no additional parameters, the CLI will then display
all of the possible next parameters.
DGS-3120-24TC:admin#show
Command: show
Next possible completions:
802.1p 802.1x aaa access_profile
account accounting acct_client address_binding
arp_spoofing_prevention arpentry asymmetric_vlan
attack_log auth_client auth_diagnostics
auth_session_statistics auth_statistics authen
authen_enable authen_login authen_policy authentication
authorization autoconfig backup bandwidth_control
boot_file bpdu_protection cfm command
command_history community_encryption config
cpu cpu_filter current_config ddm
device_status dhcp dhcp_local_relay dhcp_relay
dhcp_server dhcpv6_local_relay dhcpv6_relay
dlms dos_prevention dot1v_protocol_group
dscp duld dvmrp ecmp
eee egress_access_profile egress_flow_meter
environment erps error ethernet_oam
execute_config fdb filter flow_meter
gratuitous_arp greeting_message gvrp hol_prevention
host_name igmp igmp_proxy igmp_snooping
ip ip_tunnel ipfdb ipif
ipif_ipv6_link_local_auto ipmc ipmroute
iproute ipv6 ipv6route jumbo_frame
jwac l2protocol_tunnel lacp_port led
limited_multicast_addr link_aggregation lldp
lldp_med log log_save_timing
log_software_module loopback loopdetect

xStack® DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
6
mac_based_access_control mac_based_access_control_local
mac_based_vlan mac_notification max_mcast_group
mcast_filter_profile md5 mirror
mld mld_proxy mld_snooping multicast
multicast_fdb name_server nlb ospf
ospfv3 packet password_recovery per_queue
pim pim-ssm pim6 policy_route
port port_group port_security
port_security_entry port_vlan ports
power_saving pppoe private_vlan pvid
qinq radius reboot rip
ripng rmon route route_map
router_ports rspan safeguard_engine scheduling
scheduling_mechanism serial_port session
sflow sftp sim smtp
snmp sntp ssh ssl
stack_device stack_information stacking_mode
storage_media_info stp surveillance_vlan
switch syslog system_severity tech_support
terminal time time_range traffic
traffic_segmentation trap trusted_host
udp_helper utilization vlan vlan_counter
vlan_translation vlan_trunk voice_vlan vrrp
wac wred
DGS-3120-24TC:admin#
In the above example, all of the possible next parameters for the show command are displayed. At
the next command prompt, the up arrow was used to re-enter the show command, followed by the
account parameter. The CLI then displays the user accounts configured on the Switch.
1-3 Command Syntax Symbols
Syntax Description
angle brackets < > Encloses a variable or value. Users must specify the variable or value.
For example, in the syntax
config command_history <value 1-40>
users must enter how many entries for <value 1-40> when entering the
command. DO NOT TYPE THE ANGLE BRACKETS.
square brackets [ ] Encloses a required value or list of required arguments. Only one value or
argument must be specified. For example, in the syntax
create account [admin | operator | power_user | user] <username 15>
{encrypt [plain_text | sha_1] <password>}
users must specify either the admin, operator, power_user or user-level
account when entering the command. DO NOT TYPE THE SQUARE
BRACKETS.
vertical bar | Separates mutually exclusive items in a list. For example, in the syntax
reset {[config | system]} {force_agree}
users must specify either the community or trap receiver in the command.
DO NOT TYPE THE VERTICAL BAR.

xStack® DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
7
braces { } Encloses an optional value or a list of optional arguments. One or more
values or arguments can be specified. For example, in the syntax
reset {[config | system]} {force_agree}
users may choose configure or system in the command. DO NOT TYPE
THE BRACES.
parentheses ( ) Indicates at least one or more of the values or arguments in the preceding
syntax enclosed by braces must be specified. For example, in the syntax
config bpdu_protection ports [<portlist> | all] {state [enable | disable] |
mode [drop | block | shutdown]}(1)
users have the option to specify hops or time or both of them. The "(1)"
following the set of braces indicates at least one argument or value within
the braces must be specified. DO NOT TYPE THE PARENTHESES.
ipif <ipif_name 12>
metric <value 1-31> 12 means the maximum length of the IP interface name.
1-31 means the legal range of the metric value.
1-4 Line Editing Keys
Keys Description
Delete Delete character under cursor and shift remainder of line to left.
Backspace Delete character to left of cursor and shift remainder of line to left.
CTRL+R Toggle on and off. When toggled on, inserts text and shifts previous
text to right.
Left Arrow Move cursor to left.
Right Arrow Move cursor to right
Tab Help user to select appropriate token.
P or p Display the previous page.
N, n or Space Display the next page.
CTRL+C Escape from displayed pages.
ESC Escape from displayed pages.
Q or q Escape from displayed pages.
R or r refresh the displayed pages
A or a Display the remaining pages. (The screen display will not pause again.)
Enter Display the next line.
The screen display pauses when the show command output reaches the end of the page.
In the above example, all of the possible next parameters for the show command are displayed. At
the next command prompt, the up arrow was used to re-enter the show command, followed by the
account parameter. The CLI then displays the user accounts configured on the Switch.

xStack® DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
8
Chapter 2 Basic Command List
show session
show serial_port
config serial_port {baud_rate [9600 | 19200 | 38400 | 115200] | auto_logout [never | 2_minutes |
5_minutes | 10_minutes | 15_minutes]}
enable clipaging
disable clipaging
login
logout
?
clear
show command_history
config command_history <value 1-40>
config greeting_message {default}
show greeting_message
config command_prompt [<string 16> | username | default]
config terminal width [default | <value 80-200>]
show terminal width
config ports [<portlist> | all] {medium_type [fiber | copper]} {speed [auto {capability_advertised
{10_half | 10_full | 100_half | 100_full | 1000_full}} | 10_half | 10_full | 100_half | 100_full |
1000_full {[master | slave]}] | auto_negotiation [restart_an | remote_fault_advertised [disable |
offline | link_fault | auto_negotiation_error]] | flow_control [enable | disable] | learning [enable |
disable ] | state [enable | disable] | mdix [auto | normal | cross] | [description <desc 1-32> |
clear_description] | auto_speed_downgrade [enable | disable]}
show ports {<portlist>} {[description | err_disabled | auto_negotiation | details | media_type]}
2-1 show session
Description
This command is used to display a list of currently users which are login to CLI sessions.
Format
show session
Parameters
None.
Restrictions
Only Administrator and Operator-level users can issue this command.
Example
To disable the password encryption:

xStack® DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
9
DGS-3120-24TC:admin#show session
Command: show session
ID Live Time From Level User
--- ------------ --------------------------------------- ----- ---------------
8 00:04:17.870 Serial Port admin Anonymous
Total Entries: 1
CTRL+C ESC qQuit SPACE nNext Page pPrevious Page rRefresh
2-2 show serial_port
Description
This command is used to display the current serial port settings.
Format
show serial_port
Parameters
None.
Restrictions
None.
Example
To display the serial port setting:
DGS-3120-24TC:admin# show serial_port
Command: show serial_port
Baud Rate : 9600
Data Bits : 8
Parity Bits : None
Stop Bits : 1
Auto-Logout : 10 minutes
DGS-3120-24TC:admin#
2-3 config serial_port
Description
This command is used to configure the serial bit rate that will be used to communicate with the
management host and the auto logout time for idle connections.

xStack® DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
10
Format
config serial_port {baud_rate [9600 | 19200 | 38400 | 115200] | auto_logout [never |
2_minutes | 5_minutes | 10_minutes | 15_minutes]}
Parameters
baud_rate - (Optional) The serial bit rate that will be used to communicate with the management
host. The default baud rate is 115200.
9600 - Specify the serial bit rate to be 9600.
19200 - Specify the serial bit rate to be 19200.
38400 - Specify the serial bit rate to be 38400.
115200 - Specify the serial bit rate to be 115200.
auto_logout - (Optional) The auto logout time out setting:
never - Never timeout.
2_minutes - When idle over 2 minutes, the device will auto logout.
5_minutes - When idle over 5 minutes, the device will auto logout.
10_minutes - When idle over 10 minutes, the device will auto logout.
15_minutes - When idle over 15 minutes, the device will auto logout.
Restrictions
Only Administrator and Operator-level users can issue this command.
Example
To configure baud rate:
DGS-3120-24TC:admin# config serial_port baud_rate 9600
Command: config serial_port baud_rate 9600
Success.
DGS-3120-24TC:admin#
2-4 enable clipaging
Description
This command is used to enable the pausing of the screen display when the show command
output reaches the end of the page. For those show commands that provide the display refresh
function, the display will not be refreshed when clipaging is disabled. The default setting is enabled.
Format
enable clipaging
Parameters
None.

xStack® DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
11
Restrictions
Only Administrator and Operator-level users can issue this command.
Example
To enable pausing of the screen display when show command output reaches the end of the page:
DGS-3120-24TC:admin# enable clipaging
Command: enable clipaging
Success.
DGS-3120-24TC:admin#
2-5 disable clipaging
Description
This command is used to disable the pausing of the screen display when the show command
output reaches the end of the page. The default setting is enabled.
Format
disable clipaging
Parameters
None.
Restrictions
Only Administrator and Operator-level users can issue this command.
Example
To disable pausing of the screen display when show command output reaches the end of the page:
DGS-3120-24TC:admin# disable clipaging
Command: disable clipaging
Success.
DGS-3120-24TC:admin#
2-6 login
Description
This command is used to allow user login to the Switch.

xStack® DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
12
Format
login
Parameters
None.
Restrictions
None.
Example
To login the Switch with a user name dlink:
DGS-3120-24TC:admin# login
Command: login
UserName:dlink
PassWord:****
DGS-3120-24TC:admin#
2-7 logout
Description
This command is used to logout the facility.
Format
logout
Parameters
None.
Restrictions
None.
Example
To logout current user:

xStack® DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
13
DGS-3120-24TC:admin# logout
Command: logout
**********
* Logout *
**********
Press any key to login...
DGS-3120-24TC Gigabit Ethernet Switch
Command Line Interface
Firmware: Build 4.00.015
Copyright(C) 2014 D-Link Corporation. All rights reserved.
UserName:
2-8 ?
Description
This command is used to display the usage description for all commands in the cuurent login
account level or the specific one.
Format
?
Parameters
None.
Restrictions
None.
Example
To get “ping” command usage, descriptions:
DGS-3120-24TC:admin#? ping
Command: ? ping
Command: ping
Usage: <ipaddr> { times <value 1-255> | timeout <sec 1-99>}
Description: Used to test the connectivity between network devices.
DGS-3120-24TC:admin#

xStack® DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
14
2-9 clear
Description
The command is used to clear screen.
Format
clear
Parameters
None.
Restrictions
None.
Example
To clear screen:
DGS-3120-24TC:admin# clear
Command: clear
DGS-3120-24TC:admin#
2-10 show command_history
Description
The command is used to display command history.
Format
show command_history
Parameters
None.
Restrictions
None.
Example
To display command history:

xStack® DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
15
DGS-3120-24TC:admin#show command_history
Command: show command_history
? ping
login
show serial_port
show session
? config bpdu_protection ports
? reset
? create account
? create ipif
show
the
?
DGS-3120-24TC:admin#
2-11 config command_history
Description
This command is used to configure the number of commands that the Switch can recall. The
Switch “remembers” upto the last 40 commands you entered.
Format
config command_history <value 1-40>
Parameters
<value 1-40> - Enter the number of commands that the Switch can recall. This value must be
between 1 and 40.
Restrictions
None.
Example
To configure the number of command history:
DGS-3120-24TC:admin# config command_history 25
Command: config command_history 25
Success.
DGS-3120-24TC:admin#
2-12 config greeting_message
Description
This command is used to configure the greeting message (or banner).