D-MAX PLG211 User manual

1 2 3 5 5 6 74
LED-Taschenlampe
▯Zu Ihrer Sicherheit
Lesen Sie die Bedienungsanleitung aufmerksam durch
und beachten Sie die Hinweise bei der Handhabung.
Bewahren Sie die Bedienungsanleitung für eine spätere
Verwendung auf.
Wichtige Informationen zu den Themen Sicherheit, Entsorgung,
Garantie sowie Pegehinweise entnehmen Sie dem beigefügten
Hinweisblatt.
▯Bestimmungsgemäße Verwendung
Das Produkt ist zur Anwendung im Innen- und Außenbereich be-
stimmt. Das Produkt ist nur für den privaten Gebrauch bestimmt
und nicht für den gewerblichen Einsatz oder für andere Einsatzbe-
reiche.
Die Taschenlampe ist nicht für die Raumbeleuchtung im Haushalt
geeignet.
▯Sicherheitshinweise beachten
Lesen und beachten Sie die Sicherheitshinweise, um sich und die
Umwelt zu schützen. Die Sicherheitshinweise entnehmen Sie dem
beigefügten Hinweisblatt.
▯Übersicht
Die Abbildung zeigt Ihnen die Taschenlampe im Detail.
1
Lampenkopf
4
Dichtungsring
7
Druckschalter
2
Gehäuse
5
Batterien
3
Clip
6
Endkappe
▯Verpackungsinhalt prüfen
Prüfen Sie den Lieferumfang, bevor Sie Ihr Gerät in Betrieb neh-
men. Sollte etwas fehlen oder beschädigt sein, wenden Sie sich an
unseren Servicepartner.
▸1 × LED-Taschenlampe (inkl. Clip)
▸2 × Batterie
▸1 × Geschenkbox
▸1 × Anleitung
▯Batterien einlegen
1. Schrauben Sie die Endkappe
6
vom Gehäuse
2
ab. Achten Sie
darauf, dass der Dichtungsring
4
zwischen der Endkappe
6
und dem Gehäuse
2
nicht verrutscht.
2. Legen Sie die Batterien
5
in der richtigen Ausrichtung in das
Gehäuse
2
ein.
3. Schrauben Sie die Endkappe
6
wieder auf das Gehäuse
2
auf.
Die Taschenlampe ist nur wasser- und staubdicht, wenn der
zwischen der Endkappe
6
und dem Gehäuse
2
eingesetzte
Dichtungsring
4
korrekt eingesetzt ist.
Die Taschenlampe ist jetzt betriebsbereit.
▯Taschenlampe bedienen
Mit dem Clip
3
können Sie die Taschenlampe z.B.an einer Tasche
befestigen.
Die Taschenlampe hat 2 Betriebsarten, die Sie über den Druck-
schalter
7
auswählen können.
Der Schaltzyklus für die Betriebsarten der Taschenlampe funktio-
niert wie folgt:
Betriebsart 1 èAus èBetriebsart 2 èAus
Betriebsart 1 maximale Helligkeit (100 % Leuchtkraft)
Betriebsart 2 Sparmodus (50 % Leuchtkraft)
Drücken Sie den Druckschalter
7
mehrfach, bis die gewünschte
Betriebsart ausgewählt ist.
1. Drücken Sie den Druckschalter
7
, um die Betriebsart 1 auszu-
wählen.
2. Drücken Sie den Druckschalter
7
, um die Taschenlampe
auszuschalten.
3. Drücken Sie den Druckschalter
7
, um die Betriebsart 2 auszu-
wählen.
Schnellauswahl der Betriebsarten
Optional können die Betriebsarten schnell ausgewählt werden.
Hierbei werden die Betriebsarten wie zuvor beschrieben ausge-
wählt, ohne dass die Taschenlampe beim Auswählen der Betriebs-
art ausgeschaltet wird.
1. Drücken Sie den Druckschalter
7
, um die Betriebsart 1 auszu-
wählen.
2. Drücken Sie den Druckschalter
7
nur leicht, bis das Licht
erlischt.
3. Lassen Sie den Druckschalter
7
wieder los. Die nächste
Betriebsart ist ausgewählt.
Fokussierungsfunktion
Die Taschenlampe verfügt im Lampenkopf über eine stufenlose
Fokussierungsfunktion. Mit dieser Funktion können Sie den Licht-
kegel streuen (vergrößern) oder fokussieren (verkleinern).
1. Schieben Sie den Lampenkopf
1
vom Gehäuse
2
weg, um den
Lichtkegel zu fokussieren (verkleinern).
2. Ziehen sie den Lampenkopf
1
in Richtung Gehäuse
2
, um den
Lichtkegel zu streuen (vergrößern).
▯Technische Daten
Bezeichnung LED-Taschenlampe PLG211
Hauptmaterial Aluminium
Gewicht (ohne Bat-
terien)
52 g
Maße 22 × 147 mm
Batterien 2 × Alkaline-Batterien, Typ AAA,
1,5 V ⎓ (DC, Gleichspannung)
Leuchtmittel
(nicht austauschbar)
OSRAM-LED
Leuchtdauer (nach
ANSI-Standard)
ca. 80 Minuten (100 % Leuchtkraft)
ca. 180 Minuten (50 % Leuchtkraft)
Leuchtweite (nach
ANSI-Standard)
max. 55 Meter
Helligkeit max. 100 Lumen
Lebensdauer (LED) ca. 50000 Stunden
Funktionen 2 Betriebsarten (maximale Helligkeit
(100%), Sparmodus (50%))
Schnellauswahl der Betriebsarten
Fokussierungsfunktion
Schutzart Wasser- und Staubdicht
PLG211
DBedienungsanleitung
GOperating Manual
DDD
DD  D
▯Hersteller
GO Europe GmbH
Zum Kraftwerk 1
D-45527 Hattingen
GERMANY
20201111_uni_taschenlampe_PLG211.indd 120201111_uni_taschenlampe_PLG211.indd 1 11.11.2020 10:09:5411.11.2020 10:09:54

▯Observe the Safety Information
Read and observe all the safety information to protect yourself
and the environment from any harm. Refer to the information
sheet enclosed for the relevant information on safety.
▯General View
The illustration depicts the torch in detail.
1
Lamp head
4
Sealing ring
7
Press switch
2
Housing
5
Batteries
3
Clip
6
End cap
▯Checking the Package Contents
Check the package contents carefully before putting the device
into operation. If anything is missing or damaged, please contact
our Service partners.
▸1 × LED torch (including clip)
▸2 × batteries
▸1 × gift box
▸1 × manual
▯Inserting the Batteries
1. Unscrew the end cap
6
from the housing
2
. Pay attention that
the sealing ring
4
between the end cap
6
and housing
2
does
not slip.
2. Insert the batteries
5
in the housing
2
ensuring they are
properly aligned.
3. Screw the end cap
6
back on the housing
2
.
The torch is only waterproof and dustproof when the sealing
ring
4
between the end cap
6
and housing
2
has been inserted
properly.
The torch is now ready for use.
▯Operating the Torch
You can use the clip
3
to attach the torch to your pocket, for
example.
The torch can operate in two operating modes which are selected
by pressing the press switch
7
.
The switching cycle of the operating modes is as follows:
Operating mode 1 è O󰀨 èOperating mode 2 è O󰀨
Operating
mode 1 Maximum brightness (100% intensity)
Operating
mode 2 Energy-save mode (50% intensity)
Press the press switch
7
as often as necessary until the required
mode is activated.
1. Press the press switch
7
to select operating mode 1.
2. Press the press switch
7
to switch the torch o.
3. Press the press switch
7
to select operating mode 2.
Quick Selection of Operating Modes
There is an optional method with which to select the operating
mode required more quickly. In this case, select the operating
modes as described above without switching the torch o during
the selection process.
1. Press the press switch
7
to select operating mode 1.
2. Press the press switch
7
lightly until the torch goes out.
3. Release the press switch
7
. The next operating mode in the
cycle is selected.
Focusing Function
The torch is provided with a continuous adjustment focusing
function through sliding the torch head. This function can be used
to adjust the beam of light produced, either to enlarge the area
illuminated or reduce and intensify the area illuminated.
1. Slide the torch head
1
away from the housing
2
to focus
(concentrate) the beam of light.
2. Slide the torch head
1
towards the housing
2
to scatter
(enlarge) the beam of light.
▯Technical Data
Designation PLG211 LED torch
Main material Aluminium
Weight (without
batteries)
52 g
Dimensions 22 × 147 mm
Batteries 2 × alkaline batteries, AAA,
1.5 V ⎓ (DC)
Illuminant
(not replaceable)
OSRAM LED
Lighting period
(compliant with
ANSI standard)
Approx. 80 minutes (100% brightness)
Approx. 180 minutes (50% brightness)
Lighting range
(compliant with
ANSI standard)
Max. 55 meters
Brightness Max. 100 lumen
Service life (LED) Approx. 50,000 hours
Functions 2 operating modes (maximum brightness
(100%), energy-save mode (50%))
Quick selection of operating modes
Focusing function
Type of protection Waterproof and dustproof
▯Manufacturer
GO Europe GmbH
Zum Kraftwerk 1
D-45527 Hattingen
GERMANY
GG G
GG
1 2 3 5 5 6 74
LED Torch
▯For Your Safety
Read the operating manual thoroughly and observe the
information contained when using the device. Keep the
manual close by for future reference.
Refer to the information sheet enclosed for important
information on the subjects of safety, disposal, guarantee and
product care.
▯Intended Use
The product is designed for use both indoors and outdoors. The
product is intended purely for private use and not for commercial
purposes or other usage.
The torch is not suitable for lighting rooms within a household.
G
GO Europe GmbH
Zum Kraftwerk 1
45527 Hattingen
GERMANY
11 / 2020
Art.-No. 40413
20201111_uni_taschenlampe_PLG211.indd 220201111_uni_taschenlampe_PLG211.indd 2 11.11.2020 10:09:5511.11.2020 10:09:55

▯Observe the Safety Information
Read and observe all the safety information to protect yourself
and the environment from any harm. Refer to the information
sheet enclosed for the relevant information on safety.
▯General View
The illustration depicts the torch in detail.
1
Lamp head
4
Sealing ring
7
Press switch
2
Housing
5
Batteries
3
Clip
6
End cap
▯Checking the Package Contents
Check the package contents carefully before putting the device
into operation. If anything is missing or damaged, please contact
our Service partners.
▸1 × LED torch (including clip)
▸2 × batteries
▸1 × gift box
▸1 × manual
▯Inserting the Batteries
1. Unscrew the end cap
6
from the housing
2
. Pay attention that
the sealing ring
4
between the end cap
6
and housing
2
does
not slip.
2. Insert the batteries
5
in the housing
2
ensuring they are
properly aligned.
3. Screw the end cap
6
back on the housing
2
.
The torch is only waterproof and dustproof when the sealing
ring
4
between the end cap
6
and housing
2
has been inserted
properly.
The torch is now ready for use.
▯Operating the Torch
You can use the clip
3
to attach the torch to your pocket, for
example.
The torch can operate in two operating modes which are selected
by pressing the press switch
7
.
The switching cycle of the operating modes is as follows:
Operating mode 1 è O󰀨 èOperating mode 2 è O󰀨
Operating
mode 1 Maximum brightness (100% intensity)
Operating
mode 2 Energy-save mode (50% intensity)
Press the press switch
7
as often as necessary until the required
mode is activated.
1. Press the press switch
7
to select operating mode 1.
2. Press the press switch
7
to switch the torch o.
3. Press the press switch
7
to select operating mode 2.
Quick Selection of Operating Modes
There is an optional method with which to select the operating
mode required more quickly. In this case, select the operating
modes as described above without switching the torch o during
the selection process.
1. Press the press switch
7
to select operating mode 1.
2. Press the press switch
7
lightly until the torch goes out.
3. Release the press switch
7
. The next operating mode in the
cycle is selected.
Focusing Function
The torch is provided with a continuous adjustment focusing
function through sliding the torch head. This function can be used
to adjust the beam of light produced, either to enlarge the area
illuminated or reduce and intensify the area illuminated.
1. Slide the torch head
1
away from the housing
2
to focus
(concentrate) the beam of light.
2. Slide the torch head
1
towards the housing
2
to scatter
(enlarge) the beam of light.
▯Technical Data
Designation PLG211 LED torch
Main material Aluminium
Weight (without
batteries)
52 g
Dimensions 22 × 147 mm
Batteries 2 × alkaline batteries, AAA,
1.5 V ⎓ (DC)
Illuminant
(not replaceable)
OSRAM LED
Lighting period
(compliant with
ANSI standard)
Approx. 80 minutes (100% brightness)
Approx. 180 minutes (50% brightness)
Lighting range
(compliant with
ANSI standard)
Max. 55 meters
Brightness Max. 100 lumen
Service life (LED) Approx. 50,000 hours
Functions 2 operating modes (maximum brightness
(100%), energy-save mode (50%))
Quick selection of operating modes
Focusing function
Type of protection Waterproof and dustproof
▯Manufacturer
GO Europe GmbH
Zum Kraftwerk 1
D-45527 Hattingen
GERMANY
GG G
GG
1 2 3 5 5 6 74
LED Torch
▯For Your Safety
Read the operating manual thoroughly and observe the
information contained when using the device. Keep the
manual close by for future reference.
Refer to the information sheet enclosed for important
information on the subjects of safety, disposal, guarantee and
product care.
▯Intended Use
The product is designed for use both indoors and outdoors. The
product is intended purely for private use and not for commercial
purposes or other usage.
The torch is not suitable for lighting rooms within a household.
G
GO Europe GmbH
Zum Kraftwerk 1
45527 Hattingen
GERMANY
11 / 2020
Art.-No. 40413
20201111_uni_taschenlampe_PLG211.indd 220201111_uni_taschenlampe_PLG211.indd 2 11.11.2020 10:09:5511.11.2020 10:09:55

▯Observe the Safety Information
Read and observe all the safety information to protect yourself
and the environment from any harm. Refer to the information
sheet enclosed for the relevant information on safety.
▯General View
The illustration depicts the torch in detail.
1
Lamp head
4
Sealing ring
7
Press switch
2
Housing
5
Batteries
3
Clip
6
End cap
▯Checking the Package Contents
Check the package contents carefully before putting the device
into operation. If anything is missing or damaged, please contact
our Service partners.
▸1 × LED torch (including clip)
▸2 × batteries
▸1 × gift box
▸1 × manual
▯Inserting the Batteries
1. Unscrew the end cap
6
from the housing
2
. Pay attention that
the sealing ring
4
between the end cap
6
and housing
2
does
not slip.
2. Insert the batteries
5
in the housing
2
ensuring they are
properly aligned.
3. Screw the end cap
6
back on the housing
2
.
The torch is only waterproof and dustproof when the sealing
ring
4
between the end cap
6
and housing
2
has been inserted
properly.
The torch is now ready for use.
▯Operating the Torch
You can use the clip
3
to attach the torch to your pocket, for
example.
The torch can operate in two operating modes which are selected
by pressing the press switch
7
.
The switching cycle of the operating modes is as follows:
Operating mode 1 è O󰀨 èOperating mode 2 è O󰀨
Operating
mode 1 Maximum brightness (100% intensity)
Operating
mode 2 Energy-save mode (50% intensity)
Press the press switch
7
as often as necessary until the required
mode is activated.
1. Press the press switch
7
to select operating mode 1.
2. Press the press switch
7
to switch the torch o.
3. Press the press switch
7
to select operating mode 2.
Quick Selection of Operating Modes
There is an optional method with which to select the operating
mode required more quickly. In this case, select the operating
modes as described above without switching the torch o during
the selection process.
1. Press the press switch
7
to select operating mode 1.
2. Press the press switch
7
lightly until the torch goes out.
3. Release the press switch
7
. The next operating mode in the
cycle is selected.
Focusing Function
The torch is provided with a continuous adjustment focusing
function through sliding the torch head. This function can be used
to adjust the beam of light produced, either to enlarge the area
illuminated or reduce and intensify the area illuminated.
1. Slide the torch head
1
away from the housing
2
to focus
(concentrate) the beam of light.
2. Slide the torch head
1
towards the housing
2
to scatter
(enlarge) the beam of light.
▯Technical Data
Designation PLG211 LED torch
Main material Aluminium
Weight (without
batteries)
52 g
Dimensions 22 × 147 mm
Batteries 2 × alkaline batteries, AAA,
1.5 V ⎓ (DC)
Illuminant
(not replaceable)
OSRAM LED
Lighting period
(compliant with
ANSI standard)
Approx. 80 minutes (100% brightness)
Approx. 180 minutes (50% brightness)
Lighting range
(compliant with
ANSI standard)
Max. 55 meters
Brightness Max. 100 lumen
Service life (LED) Approx. 50,000 hours
Functions 2 operating modes (maximum brightness
(100%), energy-save mode (50%))
Quick selection of operating modes
Focusing function
Type of protection Waterproof and dustproof
▯Manufacturer
GO Europe GmbH
Zum Kraftwerk 1
D-45527 Hattingen
GERMANY
GG G
GG
1 2 3 5 5 6 74
LED Torch
▯For Your Safety
Read the operating manual thoroughly and observe the
information contained when using the device. Keep the
manual close by for future reference.
Refer to the information sheet enclosed for important
information on the subjects of safety, disposal, guarantee and
product care.
▯Intended Use
The product is designed for use both indoors and outdoors. The
product is intended purely for private use and not for commercial
purposes or other usage.
The torch is not suitable for lighting rooms within a household.
G
GO Europe GmbH
Zum Kraftwerk 1
45527 Hattingen
GERMANY
11 / 2020
Art.-No. 40413
20201111_uni_taschenlampe_PLG211.indd 220201111_uni_taschenlampe_PLG211.indd 2 11.11.2020 10:09:5511.11.2020 10:09:55

▯Observe the Safety Information
Read and observe all the safety information to protect yourself
and the environment from any harm. Refer to the information
sheet enclosed for the relevant information on safety.
▯General View
The illustration depicts the torch in detail.
1
Lamp head
4
Sealing ring
7
Press switch
2
Housing
5
Batteries
3
Clip
6
End cap
▯Checking the Package Contents
Check the package contents carefully before putting the device
into operation. If anything is missing or damaged, please contact
our Service partners.
▸1 × LED torch (including clip)
▸2 × batteries
▸1 × gift box
▸1 × manual
▯Inserting the Batteries
1. Unscrew the end cap
6
from the housing
2
. Pay attention that
the sealing ring
4
between the end cap
6
and housing
2
does
not slip.
2. Insert the batteries
5
in the housing
2
ensuring they are
properly aligned.
3. Screw the end cap
6
back on the housing
2
.
The torch is only waterproof and dustproof when the sealing
ring
4
between the end cap
6
and housing
2
has been inserted
properly.
The torch is now ready for use.
▯Operating the Torch
You can use the clip
3
to attach the torch to your pocket, for
example.
The torch can operate in two operating modes which are selected
by pressing the press switch
7
.
The switching cycle of the operating modes is as follows:
Operating mode 1 è O󰀨 èOperating mode 2 è O󰀨
Operating
mode 1 Maximum brightness (100% intensity)
Operating
mode 2 Energy-save mode (50% intensity)
Press the press switch
7
as often as necessary until the required
mode is activated.
1. Press the press switch
7
to select operating mode 1.
2. Press the press switch
7
to switch the torch o.
3. Press the press switch
7
to select operating mode 2.
Quick Selection of Operating Modes
There is an optional method with which to select the operating
mode required more quickly. In this case, select the operating
modes as described above without switching the torch o during
the selection process.
1. Press the press switch
7
to select operating mode 1.
2. Press the press switch
7
lightly until the torch goes out.
3. Release the press switch
7
. The next operating mode in the
cycle is selected.
Focusing Function
The torch is provided with a continuous adjustment focusing
function through sliding the torch head. This function can be used
to adjust the beam of light produced, either to enlarge the area
illuminated or reduce and intensify the area illuminated.
1. Slide the torch head
1
away from the housing
2
to focus
(concentrate) the beam of light.
2. Slide the torch head
1
towards the housing
2
to scatter
(enlarge) the beam of light.
▯Technical Data
Designation PLG211 LED torch
Main material Aluminium
Weight (without
batteries)
52 g
Dimensions 22 × 147 mm
Batteries 2 × alkaline batteries, AAA,
1.5 V ⎓ (DC)
Illuminant
(not replaceable)
OSRAM LED
Lighting period
(compliant with
ANSI standard)
Approx. 80 minutes (100% brightness)
Approx. 180 minutes (50% brightness)
Lighting range
(compliant with
ANSI standard)
Max. 55 meters
Brightness Max. 100 lumen
Service life (LED) Approx. 50,000 hours
Functions 2 operating modes (maximum brightness
(100%), energy-save mode (50%))
Quick selection of operating modes
Focusing function
Type of protection Waterproof and dustproof
▯Manufacturer
GO Europe GmbH
Zum Kraftwerk 1
D-45527 Hattingen
GERMANY
GG G
GG
1 2 3 5 5 6 74
LED Torch
▯For Your Safety
Read the operating manual thoroughly and observe the
information contained when using the device. Keep the
manual close by for future reference.
Refer to the information sheet enclosed for important
information on the subjects of safety, disposal, guarantee and
product care.
▯Intended Use
The product is designed for use both indoors and outdoors. The
product is intended purely for private use and not for commercial
purposes or other usage.
The torch is not suitable for lighting rooms within a household.
G
GO Europe GmbH
Zum Kraftwerk 1
45527 Hattingen
GERMANY
11 / 2020
Art.-No. 40413
20201111_uni_taschenlampe_PLG211.indd 220201111_uni_taschenlampe_PLG211.indd 2 11.11.2020 10:09:5511.11.2020 10:09:55

▯Observe the Safety Information
Read and observe all the safety information to protect yourself
and the environment from any harm. Refer to the information
sheet enclosed for the relevant information on safety.
▯General View
The illustration depicts the torch in detail.
1
Lamp head
4
Sealing ring
7
Press switch
2
Housing
5
Batteries
3
Clip
6
End cap
▯Checking the Package Contents
Check the package contents carefully before putting the device
into operation. If anything is missing or damaged, please contact
our Service partners.
▸1 × LED torch (including clip)
▸2 × batteries
▸1 × gift box
▸1 × manual
▯Inserting the Batteries
1. Unscrew the end cap
6
from the housing
2
. Pay attention that
the sealing ring
4
between the end cap
6
and housing
2
does
not slip.
2. Insert the batteries
5
in the housing
2
ensuring they are
properly aligned.
3. Screw the end cap
6
back on the housing
2
.
The torch is only waterproof and dustproof when the sealing
ring
4
between the end cap
6
and housing
2
has been inserted
properly.
The torch is now ready for use.
▯Operating the Torch
You can use the clip
3
to attach the torch to your pocket, for
example.
The torch can operate in two operating modes which are selected
by pressing the press switch
7
.
The switching cycle of the operating modes is as follows:
Operating mode 1 è O󰀨 èOperating mode 2 è O󰀨
Operating
mode 1 Maximum brightness (100% intensity)
Operating
mode 2 Energy-save mode (50% intensity)
Press the press switch
7
as often as necessary until the required
mode is activated.
1. Press the press switch
7
to select operating mode 1.
2. Press the press switch
7
to switch the torch o.
3. Press the press switch
7
to select operating mode 2.
Quick Selection of Operating Modes
There is an optional method with which to select the operating
mode required more quickly. In this case, select the operating
modes as described above without switching the torch o during
the selection process.
1. Press the press switch
7
to select operating mode 1.
2. Press the press switch
7
lightly until the torch goes out.
3. Release the press switch
7
. The next operating mode in the
cycle is selected.
Focusing Function
The torch is provided with a continuous adjustment focusing
function through sliding the torch head. This function can be used
to adjust the beam of light produced, either to enlarge the area
illuminated or reduce and intensify the area illuminated.
1. Slide the torch head
1
away from the housing
2
to focus
(concentrate) the beam of light.
2. Slide the torch head
1
towards the housing
2
to scatter
(enlarge) the beam of light.
▯Technical Data
Designation PLG211 LED torch
Main material Aluminium
Weight (without
batteries)
52 g
Dimensions 22 × 147 mm
Batteries 2 × alkaline batteries, AAA,
1.5 V ⎓ (DC)
Illuminant
(not replaceable)
OSRAM LED
Lighting period
(compliant with
ANSI standard)
Approx. 80 minutes (100% brightness)
Approx. 180 minutes (50% brightness)
Lighting range
(compliant with
ANSI standard)
Max. 55 meters
Brightness Max. 100 lumen
Service life (LED) Approx. 50,000 hours
Functions 2 operating modes (maximum brightness
(100%), energy-save mode (50%))
Quick selection of operating modes
Focusing function
Type of protection Waterproof and dustproof
▯Manufacturer
GO Europe GmbH
Zum Kraftwerk 1
D-45527 Hattingen
GERMANY
GG G
GG
1 2 3 5 5 6 74
LED Torch
▯For Your Safety
Read the operating manual thoroughly and observe the
information contained when using the device. Keep the
manual close by for future reference.
Refer to the information sheet enclosed for important
information on the subjects of safety, disposal, guarantee and
product care.
▯Intended Use
The product is designed for use both indoors and outdoors. The
product is intended purely for private use and not for commercial
purposes or other usage.
The torch is not suitable for lighting rooms within a household.
G
GO Europe GmbH
Zum Kraftwerk 1
45527 Hattingen
GERMANY
11 / 2020
Art.-No. 40413
20201111_uni_taschenlampe_PLG211.indd 220201111_uni_taschenlampe_PLG211.indd 2 11.11.2020 10:09:5511.11.2020 10:09:55

▯Observe the Safety Information
Read and observe all the safety information to protect yourself
and the environment from any harm. Refer to the information
sheet enclosed for the relevant information on safety.
▯General View
The illustration depicts the torch in detail.
1
Lamp head
4
Sealing ring
7
Press switch
2
Housing
5
Batteries
3
Clip
6
End cap
▯Checking the Package Contents
Check the package contents carefully before putting the device
into operation. If anything is missing or damaged, please contact
our Service partners.
▸1 × LED torch (including clip)
▸2 × batteries
▸1 × gift box
▸1 × manual
▯Inserting the Batteries
1. Unscrew the end cap
6
from the housing
2
. Pay attention that
the sealing ring
4
between the end cap
6
and housing
2
does
not slip.
2. Insert the batteries
5
in the housing
2
ensuring they are
properly aligned.
3. Screw the end cap
6
back on the housing
2
.
The torch is only waterproof and dustproof when the sealing
ring
4
between the end cap
6
and housing
2
has been inserted
properly.
The torch is now ready for use.
▯Operating the Torch
You can use the clip
3
to attach the torch to your pocket, for
example.
The torch can operate in two operating modes which are selected
by pressing the press switch
7
.
The switching cycle of the operating modes is as follows:
Operating mode 1 è O󰀨 èOperating mode 2 è O󰀨
Operating
mode 1 Maximum brightness (100% intensity)
Operating
mode 2 Energy-save mode (50% intensity)
Press the press switch
7
as often as necessary until the required
mode is activated.
1. Press the press switch
7
to select operating mode 1.
2. Press the press switch
7
to switch the torch o.
3. Press the press switch
7
to select operating mode 2.
Quick Selection of Operating Modes
There is an optional method with which to select the operating
mode required more quickly. In this case, select the operating
modes as described above without switching the torch o during
the selection process.
1. Press the press switch
7
to select operating mode 1.
2. Press the press switch
7
lightly until the torch goes out.
3. Release the press switch
7
. The next operating mode in the
cycle is selected.
Focusing Function
The torch is provided with a continuous adjustment focusing
function through sliding the torch head. This function can be used
to adjust the beam of light produced, either to enlarge the area
illuminated or reduce and intensify the area illuminated.
1. Slide the torch head
1
away from the housing
2
to focus
(concentrate) the beam of light.
2. Slide the torch head
1
towards the housing
2
to scatter
(enlarge) the beam of light.
▯Technical Data
Designation PLG211 LED torch
Main material Aluminium
Weight (without
batteries)
52 g
Dimensions 22 × 147 mm
Batteries 2 × alkaline batteries, AAA,
1.5 V ⎓ (DC)
Illuminant
(not replaceable)
OSRAM LED
Lighting period
(compliant with
ANSI standard)
Approx. 80 minutes (100% brightness)
Approx. 180 minutes (50% brightness)
Lighting range
(compliant with
ANSI standard)
Max. 55 meters
Brightness Max. 100 lumen
Service life (LED) Approx. 50,000 hours
Functions 2 operating modes (maximum brightness
(100%), energy-save mode (50%))
Quick selection of operating modes
Focusing function
Type of protection Waterproof and dustproof
▯Manufacturer
GO Europe GmbH
Zum Kraftwerk 1
D-45527 Hattingen
GERMANY
GG G
GG
1 2 3 5 5 6 74
LED Torch
▯For Your Safety
Read the operating manual thoroughly and observe the
information contained when using the device. Keep the
manual close by for future reference.
Refer to the information sheet enclosed for important
information on the subjects of safety, disposal, guarantee and
product care.
▯Intended Use
The product is designed for use both indoors and outdoors. The
product is intended purely for private use and not for commercial
purposes or other usage.
The torch is not suitable for lighting rooms within a household.
G
GO Europe GmbH
Zum Kraftwerk 1
45527 Hattingen
GERMANY
11 / 2020
Art.-No. 40413
20201111_uni_taschenlampe_PLG211.indd 220201111_uni_taschenlampe_PLG211.indd 2 11.11.2020 10:09:5511.11.2020 10:09:55

▯Observe the Safety Information
Read and observe all the safety information to protect yourself
and the environment from any harm. Refer to the information
sheet enclosed for the relevant information on safety.
▯General View
The illustration depicts the torch in detail.
1
Lamp head
4
Sealing ring
7
Press switch
2
Housing
5
Batteries
3
Clip
6
End cap
▯Checking the Package Contents
Check the package contents carefully before putting the device
into operation. If anything is missing or damaged, please contact
our Service partners.
▸1 × LED torch (including clip)
▸2 × batteries
▸1 × gift box
▸1 × manual
▯Inserting the Batteries
1. Unscrew the end cap
6
from the housing
2
. Pay attention that
the sealing ring
4
between the end cap
6
and housing
2
does
not slip.
2. Insert the batteries
5
in the housing
2
ensuring they are
properly aligned.
3. Screw the end cap
6
back on the housing
2
.
The torch is only waterproof and dustproof when the sealing
ring
4
between the end cap
6
and housing
2
has been inserted
properly.
The torch is now ready for use.
▯Operating the Torch
You can use the clip
3
to attach the torch to your pocket, for
example.
The torch can operate in two operating modes which are selected
by pressing the press switch
7
.
The switching cycle of the operating modes is as follows:
Operating mode 1 è O󰀨 èOperating mode 2 è O󰀨
Operating
mode 1 Maximum brightness (100% intensity)
Operating
mode 2 Energy-save mode (50% intensity)
Press the press switch
7
as often as necessary until the required
mode is activated.
1. Press the press switch
7
to select operating mode 1.
2. Press the press switch
7
to switch the torch o.
3. Press the press switch
7
to select operating mode 2.
Quick Selection of Operating Modes
There is an optional method with which to select the operating
mode required more quickly. In this case, select the operating
modes as described above without switching the torch o during
the selection process.
1. Press the press switch
7
to select operating mode 1.
2. Press the press switch
7
lightly until the torch goes out.
3. Release the press switch
7
. The next operating mode in the
cycle is selected.
Focusing Function
The torch is provided with a continuous adjustment focusing
function through sliding the torch head. This function can be used
to adjust the beam of light produced, either to enlarge the area
illuminated or reduce and intensify the area illuminated.
1. Slide the torch head
1
away from the housing
2
to focus
(concentrate) the beam of light.
2. Slide the torch head
1
towards the housing
2
to scatter
(enlarge) the beam of light.
▯Technical Data
Designation PLG211 LED torch
Main material Aluminium
Weight (without
batteries)
52 g
Dimensions 22 × 147 mm
Batteries 2 × alkaline batteries, AAA,
1.5 V ⎓ (DC)
Illuminant
(not replaceable)
OSRAM LED
Lighting period
(compliant with
ANSI standard)
Approx. 80 minutes (100% brightness)
Approx. 180 minutes (50% brightness)
Lighting range
(compliant with
ANSI standard)
Max. 55 meters
Brightness Max. 100 lumen
Service life (LED) Approx. 50,000 hours
Functions 2 operating modes (maximum brightness
(100%), energy-save mode (50%))
Quick selection of operating modes
Focusing function
Type of protection Waterproof and dustproof
▯Manufacturer
GO Europe GmbH
Zum Kraftwerk 1
D-45527 Hattingen
GERMANY
GG G
GG
1 2 3 5 5 6 74
LED Torch
▯For Your Safety
Read the operating manual thoroughly and observe the
information contained when using the device. Keep the
manual close by for future reference.
Refer to the information sheet enclosed for important
information on the subjects of safety, disposal, guarantee and
product care.
▯Intended Use
The product is designed for use both indoors and outdoors. The
product is intended purely for private use and not for commercial
purposes or other usage.
The torch is not suitable for lighting rooms within a household.
G
GO Europe GmbH
Zum Kraftwerk 1
45527 Hattingen
GERMANY
11 / 2020
Art.-No. 40413
20201111_uni_taschenlampe_PLG211.indd 220201111_uni_taschenlampe_PLG211.indd 2 11.11.2020 10:09:5511.11.2020 10:09:55