D-Parts B-Speech Tx2 User manual

- 2 -
Federal Communications Commission (FCC) Statement
15.21 You are cautioned that changes or modifications not
expressly approved by the part responsible for compliance
could void the user's authority to operate the equipment.
15.105(b) This equipment has been tested and found to com-
ply with the limits for a Class B digital device, pursuant to part
15 of the FCC rules. These limits are designed to provide rea-
sonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician
for help.

- 3 -
Operation is subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including
interference that may cause undesired operation of the
device.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits
set forth for an uncontrolled environment. End users must
follow the specific operating instructions for satisfying RF
exposure compliance. This transmitter must not be co-loca-
ted or operating in conjunction with any other antenna or
transmitter.
FCC Wireless Compliance
The antenna used with this transmitter must not be coloca-
ted or operated in conjunction with any other antenna or
transmitter subject to the conditions of the FCC Grant.
Europe–EU Declaration of Conformity
This device complies with the specifications EN 300 328,
EN 301-489 and EN 60950-1 following the provisions of the
R&TTE Directive.

GB
- 12 -
B-Speech® Stereo Transmitter TX2
User guide
Introduction
The B-Speech® TX2 offers the latest in Bluetooth
technology.
The B-Speech® TX2 transmits music data from players
which are not Bluetooth capable (e.g.: MP3 and CD player,
stereo and other players) to a Bluetooth receiver such as
the stereo headset B-Speech® Calypso or the speaker
system B-Speech® Twiddle.
The B-Speech® TX2 can be used with any audio sources
with a 3.5 mm audio output.
Normally the B-Speech® TX2 and a Bluetooth receiver esta-
blish a connection automatically, as if using "Plug and Play".
After being turned on, the transmitter automatically scans,
then pairs and connects to the receiver.
Note: Please read about pairing in the user guide of your
Bluetooth receiver.

GB
- 13 -
Technical data:
·Bluetooth V. 2.0, Class II, 10 meters
·Bluetooth stereo profile: A2DP
·Frequency: 2.4 GHz
· High Quality stereo IC
·Certified CE and FCC
·3,5 mm stereo connector
·Sleep mode for energy saving
·Operation time: max. 5 hours
·Dimensions: L 48 x W 29,4 x H 12,5 mm
Start
The contents of the package consist of:
·B-Speech® stereo transmitter TX2
·Cable charger USB (portable charger optional)
·This user guide.
Please check that all the parts are present and intact.
Contact your dealer as soon as possible if anything is
missing or damaged.

GB
- 14 -
Get acquainted with the B-Speech® TX2
Charging
1. Connect the USB plug on the other end of the cable
charger to the USB input of your PC, laptop or optional
power supply.
2. Connect the cable charger mini USB plug to the mini
USB input of the B-Speech® TX2. The red LED lights up
during charging.
3. When charging is done, the red LED goes off.
90° swivel 3,5 mm
connector
Mini USB charger
connection
On / Off switch
LED indicator
(under the cover)

GB
- 15 -
4. Remove the cable charger.
Pairing the B-Speech® TX2 with the receiver
"Pairing" means making a wireless connection between the
transmitter and the Bluetooth receiver.
Before being able to use B-Speech® TX2 with a receiver,
you need to pair them.
After being turned on, the transmitter automatically scans,
pairs and connects to the receiver.
Once pairing is established, both devices search for each
other and connect automatically whenever they are
switched on.
Important note: B-Speech® TX2 pairs only with receivers
which have a factory PIN-Code equal to '0000', '1234' or
'8888'.
After pairing, you can use B-Speech® TX2 with the
Bluetooth receiver.
If you wish to use B-Speech® TX2 with another receiver,
you need to pair them also.
In this case, B-Speech® TX2 will not re-connect with the
previous device until you pair them again.

GB
- 16 -
The pairing process
1. Before pairing, please check that both devices are fully
charged.
2. Check that both devices are within 3 meters of each
other.
3. Turn the Bluetooth receiver on and make sure it is in
pairing mode. (If in doubt, read your receiver user guide).
4. Turn the TX2 on by pressing the On / Off button. The red
and blue LED flashes alternating for 6 seconds; the TX2
is in pairing mode.
5. Both devices should now find each other and pair. The
red and blue LED on the TX2 flashes slowly at same time
when the pairing is successful.
Turning B-Speech® TX2 on / off
Normally, both devices only need turning on after the
pairing; everything else is done automatically.
Turning on: The B-Speech® TX2 is turned on by pressing
on the On / Off button. The blue LED lights up.
Turning off: Press the On / Off button for about 5 seconds;
the blue LED goes off.
Note: Read the user guide of your Bluetooth receiver to find
out how to turn it on / off.

GB
- 17 -
Playing music
1. Insert the connector of the turned on B-Speech® TX2
into the 3,5 mm socket of the source device.
2. Make sure the receiver is turned on and within10 meters
of the B-Speech® TX2.
3. The red and blue LED from the B-Speech® TX2 indicates
that a Bluetooth connection exists by flashing slowly at
same time.
4. If the connection disappears, the sound is disrupted or
breaks down: Move the receiver nearer to the TX2.
Put the receiver in search mode and it will connect
again automatically. If the connection does not automati-
cally follow, start the pairing process again.
Please note:
1. If for any reason the B-Speech® TX2 does not play any
music, it should be restarted.(See chapter about pairing.)
2. Normally, the connection between the transmitter and the
receiver is established once the pairing process is done.
The connection can break for the following reasons:
-The distance between the devices is greater than 10
meters or an obstacle stands between the devices.
-One or both of the devices have been turned off or
must be recharged.

Visual indicators
State of the device State of the LED
GB
- 18 -
Pairing or Establishing
a connection The red and blue LED flash alternatively
Connected and playing The blue and red LED flash
simultaneously at slowly
speed
Sleep mode The blue LED flashes once
every 5 seconds
To start the search or pairing function again put the Bluetooth
receiver in search mode or start the pairing process.