D3FY SPORTS VERT3X User manual

IMPORTANT SAFETY GUIDELINES....................................................1
CRITICAL SAFETY INFORMATION.....................................................2
IMPORTANT CO2 & HPA AIR TANK SAFETY GUIDELINES...............3
GETTING STARTED.............................................................................4
MAINTAINING YOUR VERT3X PAINTBALL MARKER.........................5
TROUBLE SHOOTING.........................................................................7
VERT3X PARTS LIST.............................................................................8
WARRANTY.........................................................................................10
TABLE OF CONTENTS
INCLUDES •17.27mm (.68 CALIBER) VERT3X PAINTBALL MARKER •30.48cm (12”) ONE PIECE BARREL (AUTOCOCKER THREAD) •SPARE PARTS KIT •TOOL KIT •BARREL BLOCKING DEVICE
REQUIRED : CO2/HPA ONLY and Loader (not included) but are required for regulation play.
WARNING
This is not a toy. Misuse may cause serious injury or death. Eye protection designed specically for paintball must be worn by the user and persons within range.
Recommended 18 years or older to purchase. Persons under 18 must have adult supervision. READ OWNER’S MANUAL BEFORE USING

• Always remove the air source and all paintballs from the paintball
marker, before disassembly or for maintenance.
• Do not exceed 82.74bar (1200psi) input pressure.
• Use 17.27mm (.68 caliber) paintballs that meet ASTM/CE
specications only.
• Using a paintball marker outside of a designated paintball eld can be
illegal, and is subject to law enforcement penalties.
• Never shoot the VERT3X marker at velocities in excess of 91.5m/s
(300fps) (feet per second), or at velocities greater than local or national
laws allow. The discharge of paintballs at high velocity can cause serious
injuries or death, if misused.
• Always chronograph the VERT3X marker before playing paintball.
• Any modications or tampering of original factory parts or use of non-
authorized aftermarket accessories will Void all warranties and liabilities
from D3FY SPORTS.
• Keep your nger off the trigger until ready to shoot.
• Store the marker unloaded and degassed in a secure place.
• Transfer of Owner’s manual, any related instructions, and warnings
labels in the event of change in ownership.
• D3FY SPORTS will not be held liable for injuries or death sustained
when failing to follow the Safety Guidelines.
• If you read these instructions and do not fully understand them, or are
unsure of your ability to make necessary adjustments properly, call D3FY
SPORTS or your local pro shop for help.
IMPORTANT SAFETY GUIDELINES
• The VERT3X paintball marker is not a toy. Misuse may cause serious
injury or death.
• Please read, understand and follow the instructions in the VERT3X
Owner’s Manual.
• D3FY SPORTS recommends the customer be 18 years of age or older
to purchase this product. Person under 18 years of age must have adult
supervision when using this product.
• Any person using this product or within range of the product while in
use must wear Eyes/Face/Ear protection designed specically for the
sport of paintball and meets ASTM/CE specications F1776.
• Always keep the barrel blocking device on marker when not shooting/
playing.
• Ensure all screws and ttings are tightly secured before gassing up the
VERT3X.
• Always keep the paintball marker in “SAFE” mode until ready to
operate.
• Never point the VERT3X marker at anything you don’t wish to shoot.
• Never shoot or point the VERT3X marker at a person that is not
outtted with the proper paintball Eyes/Face/Ear Protection.
• Never shoot at animals, houses, cars or anything not related to the
sport of paintball.
• Never point or shoot the VERT3X marker at any Law Enforcement.
• Always treat the VERT3X marker as if it were loaded and able to re.
• Never look into the barrel of a paintball marker when unload/loaded.
• Only use Co2 or HPA Air tanks in the VERT3X marker.
IMPORTANT SAFETY GUIDELINES Ⅰ1

CRITICAL SAFETY INFORMATION
D3FY SPORTS reminds the user that Safety is Your Responsibility.
Protect your eyes, face and ears at all times.
Never shoot or point the VERT3X marker at a person that is not in
designated paintball facility and without the proper Eyes/Face/Ears
protection designed specically for the sport of paintball and meets
ASTM/CE specications.
Never look into the barrel of a paintball marker.
Part # and Description
(S-02) Feedneck Screw
(S-19) Front Plug Screw
(S-11) Trigger Frame Screw
(S-13) ASA Screw
IMPORTANT: Before and after using the
paintball marker, check and make sure all the
screws are securely fastened. Loose screws may
prevent the paintball marker from functioning properly.
2Ⅰ CRITICAL SAFETY INFORMATION

•Improper use, lling, storage, or disposal of all air tanks may result in
property damage, personal injury, and/or death.
•Always keep Air tanks out of reach from children or any inexperienced
person(s).
•Air tanks must only be lled by qualied and trained personnel.
•Never alter the Air tank in any way.
•DO NOT expose pressurized cylinders to temperatures in excess of
54˚C (130˚F).
•Any tank packaged with the product is intended for paintball use only.
•Tanks heated to a temperature of 121°C (250°F) or more must be re-
qualied or condemned.
•Do not expose tanks to corrosive materials and do not clean with
caustic cleaners.
•Co2/Compressed gas is dangerous, do not allow Co2/Compressed gas
to come in direct contact with your skin or try to stop a leak by covering
it with your hand.
•NEVER over pressurize a Co2 or HPA Air cylinder.
•A urethane O-ring is highly recommended before attaching any air
supply to the marker.
•Conrm that there is a urethane O-ring attached on the Co2/HPA
Air Tank Valve before attaching the tank to the marker. If the O-ring is
missing from the valve, the paintball marker will leak from the ASA as
soon as an air tank is secured to the marker.
•Always follow the warning listed on Co2/HPA tank.
IMPORTANT C02 & HPA AIR
TANK SAFETY GUIDELINES
•Only use Co2 or HPA Air Tanks that are made for the sport of paintball
•The Co2/HPA Air Tank can y off with enough force to cause property
damage, serious injury or death if the Valve unscrews from the cylinder
head. LOOK at the Valve when removing the tank from the marker.
Be sure that the valve is turning with the tank rather than remaining
stationary with the marker’s ASA.
STOP IMMEDIATELY if the valve starts to unscrew from the tank. Screw
the tank back onto the marker’s bottom ASA adapter and contact a
qualied airsmith for further assistance.
•Tank valves must only be installed or removed by qualied personnel.
•All tanks must meet ASTM/CE/DOT/TC Specications.
•See Co2 or HPA tank labels for retest dates. Tanks must be retested
periodically. Follow the warning labels listed on tanks.
•VERT3X Marker for use with rellable cylinders withstand input
pressure of 207bar (3,000psi) without catastrophic failure.
IMPORTANT CO2 & HPA AIR TANK SAFETY GUIDELINES Ⅰ 3

Important: Only use the marker in a safe and/or
designated playing eld.
10. Check the velocity m/s (fps) (feet per second) using a chronograph
designed for the sport of paintball. If adjustment is needed, adjust
the velocity by turning the Velocity/Spring Guide adjustment screw
(I-15) with a 3mm Allen key. To increase the velocity, turn the screw
in (clockwise). To decrease the velocity, turn the screw out (counter-
clockwise).
Note: After each adjustment, take a few shots for the spring to set.
Never adjust the marker to shoot above 91.5m/s (300fps)
or the eld rules/local laws permit.
11. After playing, remove all paintballs from your loader/hopper. Then
detach the loader/hopper from the paintball marker.
Caution: There may be 1-2 paintballs in the breach of the paintball
marker. In a safe direction, take a couple of shots to insure the marker
is completely clear of any paintballs.
12. Attach the barrel blocking device on the tip of the barrel.
13. Remove the Co2/HPA tank. Firmly unscrew the tank counter-
clockwise until it comes out of the ASA. Tip: When removing the air
tank, excess air will release from the ASA.
Caution: Never expose any skin to the ASA relief hole when removing
the air tank. Never store the paintball marker with an air tank attached
to the ASA.
14. Un-cock the marker by pulling the trigger once.
Note: Make sure to have the bolt of the marker in the un-cocked
position when not in use.
15. Push the safety button to the “SAFE” position.
GETTING STARTED
1. Make sure the Safety Button (I-40) is on the “SAFE” position. Push the
safety button from the “PUSH SAFE” side of the trigger frame.
2. Attach a barrel blocking device (X-02)
on the tip of the barrel.
3. Install a Co2/HPA air tank. Firmly screw the air tank clockwise into the
markers ASA (X-18). Tip: Make sure the tank is full and has a urethane
o-ring on the valve to prevent an air leak.
Note: Co2/HPA air tank is not included.
Caution: Never use any hand tools to screw the air tank on or off from
the ASA.
4. Install a paintball loader to the feedneck (X-13(A))
and tighten the Clamping Screw (S-05)
with a 3mm Allen key.
Note: Loader is not included.
5. Fill up the loader with .68 caliber paintballs that meet ASTM
specications.
6. Put on your paintball goggles and cock back the Bolt Cocking Pin
(I-05).
7. Remove the barrel blocking device from the tip of the barrel.
8. Point the marker in a “SAFE” direction before unlocking the safety
button. Unlock the safety by pushing the safety button from the “Push
F i r e ” s i d e . L o c a t e d o p p o s i t e s i d e o f “ P U S H S A F E ” o n t h e t r i g g e r f r a m e .
Caution: The VERT3X is now live and ready to re.
9. Ready to Fire.
4Ⅰ GETTING STARTED

2. Pull upward on the Bolt Cocking Pin (I-05) to disconnect from the
Striker. Remove the Delrin Bolt (I-04) by sliding it out the rear of the
Receiver/Body (X-20).
3. Wipe off any dirt,debris, or paint from the Delrin Bolt using a clean
cloth. Use a squeegee or swab to clean the inside of the Receiver.
4. Insert the Delrin Bolt with the open face in rst. Align the Bolt
Cocking Pin with the Striker hole and push down on the Pin to lock it
in place.
Important: Make sure to install the Delrin Bolt with the air passage hole
located in the middle of the bolt facing downwards.
Note: If the Delrin Bolt is not installed correctly, the paintball marker will
not function properly.
7. With the Bolt Cocking Pin properly installed to the Striker, push the
Safety button to the “Fire” position. The Delrin Bolt will slide forward
when you pull the trigger.
DISASSEMBLE REAR INTERNALS
1. With the Bolt in the un-cocked position, pull upward on the Bolt
Cocking Pin to disconnect the Delrin Bolt from the Striker. Remove the
Delrin Bolt by sliding it out the rear of the Receiver.
2. Remove the Striker Plug (X-15) by unscrewing it counter-clockwise.
This will allow you to remove the Striker Spring (I-09), Striker Buffer (I-13)
MAINTAINING YOUR VERT3X
PAINTBALL MARKER
PART # AND DESCRIPTION
(X-20-B/DB/T) RECEIVER
(I-04) DELRIN BOLT
(I-05) BOLT COCKING PIN
(I-08) STRIKER
(I-09) STRIKER SPRING - (I-10) STRIKER SPRING (HIGH VELOCITY)
(I-13) STRIKER BUFFER
(I-15) VELOCITY/SPRING GUIDE
(X-15) STRIKER PLUG
QUICK CLEAN AND DISASSEMBLE
Make sure all paintballs are removed from the marker and that the air
source is detached before attempting any maintenance and/or repairs.
1. Push the Safety button to the “SAFE” position. Cock back the bolt.
Note: This will help keep the Striker (I-08) from rotating and moving
forward.
MAINTAINING YOUR CONQU3ST PAINTBALL MARKER (CONTINUED) Ⅰ 5

4. Insert the Delrin Bolt with the open face in rst. Align the Bolt
Cocking Pin with the Striker hole, and push down on the Pin to lock it
in place.
Note: If the Striker hole is not aligned upright, the Bolt Cocking Pin will
not lock correctly.
WARNING Before and after using the marker, make sure to fasten all
screws. Screws may become loose due to vibration caused by ring
the marker. Loose screws can cause parts to detach from one another,
which can be dangerous and cause injury.
To assure that the marker is assembled properly, follow the schematic
drawing and position parts in order during assembly. Parts assembled
improperly or using improper parts will/can cause the marker to
malfunction.
CUP SEAL REMOVAL
PART # and Description
(X-21) 30.48cm (12”) Barrel
(X-05)Front Plug
(I-01)Valve Spring
(I-02)Cup Seal/Valve Pin
(S-19)Front Plug Screw
DISASSEMBLE FRONT INTERNALS
Make sure all paintballs are removed from the marker and that the
air source is detached before attempting any maintenance and/or
repairs.
1. Remove the Barrel (X-21) by unscrewing it counter-clockwise.
2. Remove Front Plug Screw (S-19) using a 3mm Allen key. This
screw holds the Front Plug (X-05) onto the Receiver.
3. Pull the Front Plug out of the Receiver.
and Striker from the rear of the Receiver.
Tip: Only remove the Striker Plug with the marker in the un-cocked
position. This will prevent the internals from springing out when the
Striker Spring is compressed.
Note: The Striker Plug and Velocity/Spring Guide will come out
as one piece.
3. Remove the following items in order; Striker Spring, Striker Buffer,
and Striker
4. Clean any dirt, debris, or paint from the inside of the Receiver.
5. Wipe the Delrin Bolt and Striker with a clean cloth. Apply a few drops
of oil to the Striker O-ring (O-03).
REASSEMBLE REAR INTERNALS
1. Insert the Striker with the O-ring end facing in rst and the at spot of
the Striker facing downwards.
Note: the Striker will only go in half way because of the Trigger Frame
Sear. Apply pressure behind the Striker with your thumb and at the
same time pull the trigger to release the Sear, this will allow the Striker
to insert all the way.
2. Insert the Striker Buffer so that it is ush with the Receiver and insert
the Striker Spring.
3. Insert the Velocity/Spring Guide into the Striker Spring, which is
connected to the Striker Plug and rmly tighten the Striker Plug to the
Receiver.
6Ⅰ MAINTAINING YOUR CONQU3ST PAINTBALL MARKER (CONTINUED)

Solution: Replace Striker O-ring and add a few drops of oil.
5. Rear internals are not properly installed.
Solution: Follow Reassemble Rear Internal steps.
AIR LEAK
Make sure all paintballs are removed from the marker and that the
air source is detached before attempting any maintenance and/or
repairs.
1. Air leaking from the Front Plug. Inspect Front Plug O-ring.
Solution: Clean any dirt, debris, or paint which can cause the o-ring
not to seal. Replace the O-ring if it is damaged or missing.
2. Air leaking down the Barrel. Cup Seal may be damaged, installed
incorrectly or missing.
Solution: Replace damaged Cup Seal or properly install the Cup Seal.
3. Air leaking between the Receiver and Trigger Frame. Valve Body
O-ring may be damaged or installed incorrectly.
Solution: Replace Valve Body O-ring or properly install the Valve
Body.
4. Air leaking from the hose fitting on the Receiver.
Solution: Remove hose and use thread sealer (Blue Loctite) on hose
thread.
5. Air leaking from the hose fitting on the ASA. Inspect Hose O-ring
Solution: Clean any dirt, debris, or paint which can cause the o-ring
not to seal. Replace the O-ring if it is damaged or missing.
6. Air leaking from the ASA relief hole.
Solution: Replace Tank Valve O-ring.
PAINT BREAKING
1. One or more Ball Detents maybe damaged or missing.
Solution: Replace Ball Detents.
4. Once the Front Plug is removed. Pull out the Valve Spring (I-01)
and Cup Seal/Valve Pin (I-02).
Note: Inspect the Cup Seal/Valve Pin for any signs of damage.
Replace the Cup Seal/Valve Pin if experiencing an air leak out the
barrel.
Reassemble Front Internals
1. Attach the Valve Spring to the Cup Seal end first. Insert the
Valve Pin end first and ensure it slides through the Valve Body.
2. Insert the Front Plug with the O-ring end facing in first and
the screw hole facing downwards.
3. Align the Front Plug screw hole with the Front Plug Screw and
fasten the Front Plug Screw.
Note: Front Plug must be flush with the Receiver for the Front Plug
Screw to align properly.
TROUBLESHOOTING
RECOCKING ISSUES
Make sure all paintballs are removed from the marker and that the
air source is detached before attempting any maintenance and/or
repairs.
1. Air tank is empty, or the pressure in the tank is too low.
Solution: Refill the tank.
2. Internals may be dirty and/or full of paint.
Solution: Clean the rear internals and Receiver.
3. Striker O-ring needs lubrication.
Solution: Add a few drops of oil on the Striker O-ring
4. Striker O-ring is damaged or missing.
TROUBLESHOOTING (CONTINUED) Ⅰ7

2. Dirt, debris, or paint is blocking the Breech.
Solution: Clean Bolt, Barrel and Receiver.
3. Loader has dirt, debris, or broken paint.
Solution: Clean loader.
Note: Using low quality paintball can cause them to break and/or
get jammed in the marker.
WARRANTY
D3FY SPORTS INC. PROVIDES A (2) YEAR WARRANTY FROM DATE
OF PURCHASE ON D3FY OEM PRODUCTS. D3FY WARRANTS THE
ORIGINAL RETAIL PURCHASER THAT THIS PRODUCT IS FREE FROM
DEFECTS IN MATERIAL AND WORKMANSHIP UNDER NORMAL USE
AND SERVICE FOR PERIOD OF (2) YEARS FROM THE DATE OF
PURCHASE. D3FY AGREES TO REPAIR OR REPLACE ANY PRODUCT
WHICH IS DEEMED TO POSSESS A MANUFACTURER DEFECT. NORMAL
WEAR AND TEAR IS NOT COVERED UNDER WARRANTY.
REGISTER YOUR MARKER AT WWW.D3FYSPORTS.COM
NOTE: WARRANTY REGISTRATION MUST BE COMPLETED BEFORE
PROCESSING A CLAIM.
PLEASE READ THE FOLLOWING
WHEN CLAIMING WARRANTY.
1. Call D3fy Sports at 909-623-8801 to first acquire a return RMA
number and an address to send your product. Note: Your RMA
number expires 15 days from the date it was issued to you by our
warranty department.
2. Send your D3fy product with the following information. A copy
of your receipt dated within 2 years from purchase. Include your
contact/shipping information. Write the RMA number on the outside
of the package you use to ship the product.
8Ⅰ TROUBLESHOOTING (CONTINUED)
D3fy Sports strongly recommends that you send your package via
a carrier which provides a tracking number. D3fy Sports is not liable
for any packages lost in transit. We are only responsible for product
we have received.
All packages received w/o an RMA number will be refused, No
Exceptions.
3. Our warranty covers repair or replacement of defective products
only, as determined by our technicians or RMA staff.
4. All products must be registered in our database within 30 days
of purchase for warranty coverage to be valid.
5. Warranty is void when the product is altered, abused, or
neglected. Any signs of alteration or unauthorized disassembly of
the product will void warranty.
6. Warranty is void when non-OEM upgrade/replacement parts
are installed. D3fy Sports will not be held responsible for the
compatibility issues between various manufactures.
7. If you don’t have your receipt or have not registered your
warranty within the time frame given, you can have your product
repaired for a nominal fee.
To assist you with any technical issues with our products, please
contact our Tech Department at [email protected] or call us at
909-623-8801
D3FY SPORTS
ATTN: Tech Department
1462 W. Holt Ave.
Pomona, CA 91768
www.d3fysports.com

NOTES

VERT3X PARTS LIST
LIST PART# DESCRIPTION QTY LIST PART# DESCRIPTION QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
*
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
1
1
1
4
1
1
1
1
2
1
2
1
2
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
4
1
1
1
1
2
1
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
X-21-B
O-05
X-05
O-01
I-01
I-02
I-03
X-20-B/DB/T
S-01
X-11(P)
I-12
X-12(P)
S-02
X-13(A)
S-05
I-04
I-05
I-06
I-07
S-06
O-03
I-08
I-09
I-10
I-13
X-15
O-04
I-15
X-16
S-08
I-16
I-18
I-21
I-23
I-25
X-17
S-09
S-11
I-26
I-27
X-18-B
S-13
S-17
S-19
X-19(A)
X-07
O-06
X-14(A)
O-07
S-14
I-40
I-35
I-33
30.48cm(12”)Barrel
Barrel O-Ring
Front Plug
Main Body O-ring
Valve Spring
CupSeal/Valve Pin
Valve Body
Receiver/Body
Ball Detent Cover Screw
Right Ball Detent Cover(Composite)
Ball Detent
Left Ball Detent Cover(Composite)
Feedneck Screw
Clamping Feedneck(Aluminum)
Clamping Screw
Derlin Bolt
Bolt Cocking Pin
Bolt Retaining Ball Bearing
Bolt Retaining Spring
Bolt Retaining Screw
Striker O-ring
Striker
Striker Spring
Striker Spring(High Velocity)
Striker Buffer
Striker Plug
Velocity/Spring Guide O-ring
Velocity/Spring Guide
Rubber Wrap Grip
Grip Screw
Sear Spring
Sear
Trigger Sear Roll Pin
Trigger Sear
Trigger Sear/Safety Button Spring
Double Trigger
Trigger Frame Screw Washer
Trigger Frame Screw
Sear Roll Pin(Short)
Sear/Trigger Roll Pin(Long)
ASA 15 Degree Angle
ASA Screw
Front Plug Screw Washer
Front Plug Screw
Aluminum Foregrip
Steel Braided Hose
Hose Seal O-ring
Aluminum Trigger Frame
Frame Air Passage O-Ring
Valve Body Screw
Safety Button
Safety Button Retaining Ball Bearing
Trigger Spring
10 Ⅰ VERT3X PARTS LIST

NOTES

1462 W. Holt Ave. Pomona, CA 91768
www.D3FYSPORTS.com