Dacor OBC36 User manual

WARNING:
NOTES:
Outdoor Grill Cart for Outdoor Grill Models
OB36 and OBS36
INSTALLATION
INSTRUCTIONS
OUTDOOR GRILL CART MODEL OBC36
Part No. 102044 Rev. G
• Since the cart and the grill are heavy, this installation process should be accom-
plished by a minimum of two people. Remove all individual components to lighten the
grill before installation. Remove the cart from the shipping pallet before installation.
• Sheet metal edges can be dangerous in heavy lifting situations. Please wear gloves
during installation.
• Attach the appliance to the cart with both of the supplied bolts before use.
• Read the use and care manual completely before operation.
• To avoid an explosion hazard, do not connect the cart or appliance(s) to electrical
power until after the gas supply system has been connected and checked for leaks.
• Toavoidarehazard,keeptheoutdoorgrillaminimumof10”fromcombustiblesur-
facesand3”fromnon-combustiblesurfacesabovethecookingsurface.
• The Dacor cart ships assembled ready for installation of the outdoor grill.
• All gas and electrical connections should be made after the grill is installed and
bolted to the cart.
• Your cart is prepared for either natural gas or liquid propane (LP) gas connections.
However, it is important to verify that your outdoor grill was ordered correctly. If you
will be utilizing LP gas, your grill must indicate LP in the model number. Do not pro-
ceed with installation if the model is not correct. Field conversion from one gas type
to another is not permissible.
• Allow 26 inches in front to open drawers.
• To prevent damage to the regulator, connect it only after the outdoor grill is attached
to the cart.
• For proper grill and drawer operation, use the outdoor grill and cart only on a level
surface.

Page 2
Grill Cart Installation Instructions Kit
ASSEMBLY:
Step1: Remove the outdoor grill from its shipping carton and
pallet. Remove the parts box to lighten the appliance.
Step 2: Set the cart in an open location and lock the wheels
on the cart to minimize potential movement.
Step 3: Remove the drawers.
Step 4: As you place the outdoor grill on the cart, feed the
electrical cord into the utility cut-out on the cart.
Step 5: Center the unit on the cart, making sure to line up the
threaded mounting holes under the bottom of the grill
with the holes in the top of the cart.
Step 6: Thread both of the supplied bolts into the bottom of
the outdoor grill from inside the cart. Tighten the bolts
into place.
Step 7: Install the side shelves if desired. See next page.
Step 8: Before installing the front drawers and tank shelf, con-
nect the regulator and gas supply line according to the
Outdoor Grill Installation Instructions.
Step 9: Install the drawers. Put the LP tank on the tank shelf
and connect it, if applicable.
Step10: Turn on the gas and check for leaks according to the Outdoor Grill Installation Instruc-
tions.
Step11: Connect a three-prong extension cord (minimum 5 Amp. capacity) to the power input on
the back of the cart. Connect the extension cord to a grounded, three-prong, electrical
outlet.
CAUTION: The largest recommended LP tank size for the rollout tank shelf
isvegallons.
WARNING:
• The grill cart is equipped with a grounded three-wire electrical system
and ground fault interrupter (GFI) electrical outlets for safety. To avoid
an electric shock hazard:
• Connect the power cords from the outdoor grill, rotisserie motor and
optional warming oven only to the electrical outlets mounted on the cart.
• Do not under any circumstances:
- Cut or remove the third (ground) prong from the appliance(s)
and rotisserie power cords.
- Do not use an adapter plug.
- Do not use an extension cord.
- Do not use a power cord that is frayed or damaged.
Bolt locations
Utility
cutout
Swiveling
wheel
Tank
shelf
Locking wheels

Grill Cart Installation Instructions Kit
Page 3
SIDE SELF INSTALLATION:
Step12: With the tank shelf open, connect the power cord from the outdoor grill and the warming
oven (if equipped with one) to the electrical outlet on the back panel inside the cart.
Step13: Connect the rotisserie motor power cord to the electrical outlet on the back side of the
cart.
Step1: Install the front mounting bracket for the right side shelf. Use two (2) of the provided
button head fasteners and two (2) lock washers. Tighten into place using a 5/32” Allen
wrench.
Bracket
Lock
washer
Button
head
fastener
Continued...

Dacor ● 600 Anton Blvd. Suite 1000 Costa Mesa, CA 92626 ● Phone: [phone] ● Fax: [phone] ● www.Dacor.com
Step 2: Slide the slot on the inside of the
shelf over the pin on the mounting
bracket.
Step 3: While holding the shelf in place,
insert the pin on the back mounting
bracket into the slot on the back
side of the shelf.
Step 4: While holding the shelf and back
mounting bracket in place, attach
the back mounting bracket using
two (2) of the provided button head
fasteners and two (2) lock washers.
Step 5: Repeat steps 1 through 4 for the
left side shelf.
Pin
NOTE: Dacor offers a protective grill cover and a grill/cart cover. For more information
concerning these options, contact your Dacor appliance dealer.