Dacor ER30D Technical manual

PLANNING
GUIDE
www.Dacor.com Phone: [phone]
Specications subject to change without notice.
Install all appliances according to accompanying installation instructions. 5.7
Epicure®Ranges
ER30D, ER30DSR
ELECTRIC CIRCUIT REQUIREMENTS
Range Model Circuit Required Total Connected
Load
ER30D/ER30DSR 240 Vac, 4-wire*
60 Hz, 30 Amp. 5.6 kW (24.2 Amp.)
The ratings above are for reference only -
refer to the range rating label
NOTE: Models ER30D and ER30D-C are NOT designed for
use with self-rimming installations or raised vents. Use model
ER30DSR for self-rimming and raised vent installations.
NOTE:
Self-rimming models are designed to allow the trim to■
overlap the countertop when configured to the dimensions
on page 1/3.
Self-rimming models are not compatible with integral■
backguards
1 9/16”
(40 mm)
23 1/8” (587 mm)
24 1/8” (613 mm)
27 3/16” (691 mm)
35 3/4”
(908 mm)
to
37 7/8”
(962 mm)
28 11/16” (729 mm)
46 1/8” (1172 mm)
Rear of front panel to
back of chassis
Rear of front panel /oven door
Front panel
Front edge of bullnose
Front of handle
Front of open door
26 3/16” (665 mm)
Width at front panel:
29 7/8” (758 mm)
1 5/16” (33 mm) to cooking
surface (top of grates) from
bottom of trim
SELf RImmING moDEL ER30DSR
SIDE DImENSIoNS
wIth oPtIoNAL RAISED VENt
tRIm kIt INStALLED (Atk30SR)
1 1/16” (27 mm)
26 5/16” (668 mm)
27 5/16” (694 mm)
28 13/16” (732 mm)
24 1/4” (616 mm)
3” (76 mm)
Backguard*
6” (152 mm)
Backguard**
** Optional
Standard
*
37 7/8”
(962 mm)
to
35 3/4”
(908 mm)
46 1/4” (1175 mm)
Width at front panel:
29 7/8” (758 mm)
Finished side panel
9” (229 mm)
1 9/16”
(40 mm)
Backguard**
1 1/16” (27 mm) to cooking
surface (top of grates) from
top of trim
fREEStANDING moDELS ER30D AND ER30D-C
1 9/16”
(40 mm)
23 1/8” (587 mm)
23 5/8” (600 mm)
26 11/16” (678 mm)
35 3/4”
(908 mm)
to
37 7/8”
(962 mm)
28 3/16” (716 mm)
45 5/8” (1159 mm)
Rear of front panel to
back of chassis
Rear of front panel /oven door
Front panel
Front edge of bullnose
Front of handle
Front of open door
25 11/16” (652 mm)
Width at front panel:
29 7/8” (758 mm)
1 5/16” (33 mm) to cooking
surface (top of grates) from
bottom of trim
SELf RImmING moDEL ER30DSR
SIDE DImENSIoNS
wIth StANDARD tRIm
Product tolerances: ±1/16” (±1.6 mm) unless otherwise stated
WARNING
Observe all governing codes and ordinances during•
planning and installation. Contact your local building
department for further information.
This appliance must be installed in accordance with•
the accompanying installation instructions.
Document # PG05-003 Revised 08/23/10 Page 1/3
* 4-wire, two 120 Vac hot (L1 and L2), one neutral, one ground

PLANNING
GUIDE
www.Dacor.com Phone: [phone]
Specications subject to change without notice.
Install all appliances according to accompanying installation instructions. 5.8
Epicure®Ranges
ER30D, ER30DSR
Note 2
F
G
2Cabinet/countertop depth is at discretion of customer but
cabinet face MUST NOT protrude further than rear of front
panel, see product dimensions.
3Consult local code for exact location requirements.
1Vertical to combustible surface from range grate level; if
installing an overhead vent hood, also check the hood
specifications for minimum required clearances.
Non-combustible
surface along
back wall
recommended
10” (254 mm) Min.
to combustible side
walls above the range
(both sides)
30” (762 mm)
Min.1
36 1/2”
(927 mm)
Max.
13” (330 mm)
Max.4
18” (457 mm)
Min.1, 4
Suggested
location of
utilities 3
4Not applicable for cabinets more than a horizontal
distance of 10” (254 mm) from the edge of the range.
CUT-OUT DIMENSIONS
F G
36” (914 mm)*
30” (762 mm)** 30 1/16” (916 mm)*
* Recommended
** Minimum
Gas and Electrical Service
The shaded area (diagram bottom left) denotes the location of■
the gas inlet and the electrical junction box/receptacle. This is the
recommended location. For replacement purposes, the location of the
existing utilities may be utilized provided they do not interfere with the
sides or rear of the range. Check local building codes for permissible
gas valve and electrical locations.
An external manual shut-off valve must be installed between the gas■
inlet and the range, for the purpose of turning on or shutting off gas to
the appliance.
The installation must allow for the following:
Access to the gas shut-off valve when the unit is installed.■
Access to the remote circuit breaker panel/fuse box, when the range■
is in place.
The gas supply piping and shut-off valve, and the electrical junction■
box/receptacle must be located so they do not interfere with the range
when it is installed.
The junction box and gas shut off valve must be located so that■
the range can be pulled out for service while the appliance remains
connected.
CAbINEt CUtoUt DImENSIoNS
moDELS ER30D AND ER3oD-C
NOTE: See following page for countertop/cabinet cutout
dimensions for self-rimming installations
Cabinet tolerances:
+1/16”, (+1.6 mm) -0
GAS SUPPLY PRESSURE REQUIREMENTS*
Gas Type Manifold Pressure Minimum Gas Supply
Pressure
Natural Gas 5” Water Column 6” Water Column
Petroleum (LP) 10” Water Column 11” Water Column
* Maximum input gas supply pressure for all models is 1/2 p.s.i.
GAS - ELECTRICAL ACCESS DIMENSIONS
ABCD E
4 7/8”
(124 mm)
21 3/4”
(552 mm)
8 5/8”
(219 mm)
10 3/16”
(259 mm)
7/8”*
(22 mm)
* The hole size can be increased to 1 1/8” by removing the conduit bracket
inside the range electrical access box.
B
Gas
inlet
A
C
7/8” (22 mm) Dia. electrical
connection hole in bottom*
D
Range electrical access,
cover removed
bACk of RANGE
Product tolerances: ±1/16” (±1.6 mm) unless otherwise stated
Document # PG05-003 Revised 08/23/10 Page 2/3

PLANNING
GUIDE
www.Dacor.com Phone: [phone]
Specications subject to change without notice.
Install all appliances according to accompanying installation instructions. 5.9
Epicure®Ranges
ER30D, ER30DSR
ER30DSR with H J K
no side panels no raised vent 23 1/2” (597 mm) 23 1/2” (597 mm) 24” to 25 9/16”
3-inch side panels* and no raised vent 20 1/2” (521 mm) 20 1/2” to 23 1/2” 21” to 25 9/16”
no side panels and raised vent 24” (610 mm) 24” (610 mm) 24 1/2” to 26 1/16”
3-inch side panels and raised vent 21” (533 mm) 21” to 24” 21 1/2” to 26 1/16”
Cutout tolerances: +1/16”, -0, (+1.6 mm, -0) unless otherwise stated
toP VIEw - moDEL ER30DSR CoUNtERtoP/CAbINEt
CUtoUt DImENSIoNS SELf RImmING INStALLAtIoN
Non-combustible
rear wall recommeded
Countertop Height: Min: 35 5/8” (905 mm) Max: 37 3/8” (949 mm)
Combustible side
wall above range
countertop opening
29 1/2” (749 mm)
30” (762 mm)
cabinet opening
below countertop
below countertop
Cabinet face
Notch countertop
overhang to width of
cabinets
1/4” Min. (6 mm)
Countertop
overhang
10” Min.
(254 mm)
both sides
Countertop front
H J K
rear wall recommended
Non-combustible
countertop opening
cabinet opening
below countertop
29 1/2” (749 mm)
27 1/2” (699 mm)
30” (762 mm)
2 3/8” (60 mm)
Combustible side
wall above range
10” Min.
(254 mm)
both sides
Countertop Height: Min: 35 5/8” (905 mm) Max: 37 1/4” (946 mm)
Notch countertop
overhang to width of
cabinets
3/8” Min. (10 mm)
Countertop
overhang
below countertop
Cabinet face
raised vent opening
H J K
Countertop front
toP VIEw - moDEL ER30DSR CoUNtERtoP/CAbINEt
CUtoUt DImENSIoNS, SELf RImmING INStALLAtIoN
wIth RAISED VENt (Atk30SR tRIm kIt INStALLED)
APPRoVED RAISED VENtS: ERV30 oR PRV30
Stiffener Cabinet face*
Countertop*
* IMPORTANT: See Countertop/Cabinet Cutout Dimensions
for countertop cutout dimensions.
** IMPORTANT: If optional 3-inch side panels are not installed
cabinet face must be flush with back of control panel.
Back of
control
panel
ERV30 or
PRV30
raised vent
ER30DSR Range:
ATK30SR trim kit
required for installation
with raised vent
3/8” Min. (10 mm)
space behind
raised vent
chassis to clear
stiffener Shown with
optional 3-inch
side panels
installed**
3/8” Min. (10 mm)
flat countertop overhang
required behind cutout
Countertop height:
35 5/8" (905 mm) Min.
37 1/4” (946 mm) Max.
Document # PG05-003 Revised 08/23/10 Page 3/3