Daedong PX Series User manual

- 1 -
Printed in Korea. JUN.2016
SERVICE SUPPORT DIVISION / DAEDONG INDUSTRIAL Co.,Ltd.
35, Nongongjungang-ro 34-gil Nongong-eup, Dalseong-gun, Daegu, KOREA 42984
Tel:[phone] Fax:[phone]
http://www.daedong.co.kr
KIOTI TRACTOR DIVISION / DAEDONG-USA, Inc.
6300 Kioti Dr. Wendell, NC 27591
Toll Free:1877-GO-KIOTI
Tel:[phone] Fax:[phone]
http://www.kioti.com
DAEDONG KIOTI EUROPE B.V
Koerilenstraat 2, 3199LR, Maasvlakte-Rotterdam The Netherlands
Tel:[phone]
http://www.kioti.eu
INSTALLATION
INSTRUCTIONS
FOR PX SERIES
WORK LAMP KIT
1. PACKING LIST & ACTUAL IMAGE
2. GENERAL SAFETY INFORMATION
3. INSTALLATION INSTRUCTION
D.D KIT#. TG15-A0003B
TG120_07_작업등키트_영문-A4.indd 1 2016-07-04 오전 8:34:28

- 2 -
1. PACKING LIST & ACTUAL IMAGE
NO. Part No. Description Q'TY Remark
1 TG15-0012A REAR WORK LAMP ASS'Y 2
2 T4625-55431 FLANGE BOLT 2
3 T5310-69802 SIDE WORK LAMP(LED) ASS'Y 2
4 02763-50080 FLANGE NUT 2
5 TG16-0226A BRACKET(LH), WORK LAMP 1
6 TG16-0227A BRACKET(RH), WORK LAMP 1
7 01023-50660 BOLT, WASHER ATTACH 4
8 T4680-93211 CAP NUT, M6 4
TG2A701C
TG120_07_작업등키트_영문-A4.indd 2 2016-07-04 오전 8:34:29

- 3 -
2. GENERAL SAFETY INFORMATION
This symbol means ATTENTION! YOUR SAFETY IS INVOLVED.
The message that follows the symbol contains important information about safety. Carefully read the
message.
BEFORE SERVICING AND REPAIRING
1. Read all safety instruction in this manual and be aware of safety decal locations on your machine.
2. Thoroughly clean your work area and the machine.
3. Makesurethemachineisonrmandlevelgroundandthattheparkingbrakeisset.
4. Lower the implement to the ground.
5. Stop the engine and remove the key.
6. Disconnect the negative battery cable.
7. Place a "DO NOT OPERATE" tag in the operator station.
WORKING SAFETY
1. Donotoperateorservicethemachinewhileundertheinuenceofalcohol,medications,orothersustances.
2. Neverwearloosettingclothingandalwaysusesafetyequipmentappropriatetothejob.
3. Never use improvised tools, parts or procedures. Use only recommended tools appropriate to the work.
4. Extra care should be taken to work safely when servicing is done by two or more persons.
5. Always support the machine with safety stands rated for the weight of the machine. Never work under a machine that
is supported solely with a jack.
6. Do not touch any rotating or hot parts while the engine is running.
7. Escaping uid (hydraulic oil) under pressure can penetrate the skin causing serious injury. Relieve pressure before
disconnecting hydraulic or fuel lines. Tighten all connections before applying pressure.
DISPOSE OF FLUIDS PROPERLY
1. Observerelevantenvironmentalprotectionregulationswhendisposingofoil.NEVERpouruidsontotheground,down
a drain, or into any body of water.
3. INSTALLATION INSTRUCTION
1. Parkthevehicleonrmandlevelground.Then,engagetheparkingbrakeandstoptheengine.
2. Pull out the cap from the rear(RH) pillar cover and unscrew the bolt to
remove the pillar cover (A).
3. Assemble the side LED work lamp (3) to the work lamp bracket (RH, 6).
TG2A702b
TG2A703b
TG120_07_작업등키트_영문-A4.indd 3 2016-07-04 오전 8:34:30

- 4 -
4. Pass the LED work lamp assembly wiring, which was assembled in Step 3, through the pillar cover hole (A) to connect
it to the wiring connector on the vehicle body.
TG2A704A TG2A710A
Be sure to remain enough length
of wire outside of the pillar before
tighten it so that lamp angle can be
adjusted freely.
•
REMARKS
5. Install the LED work lamp bracket and pillar cover to the cabin together with the bolt (7).
And insert the cap nuts (8)
※Perform installation on the left side with the same method.
TG2A706b
TG2A705A
7. Push the work lamp wiring through the hole A to pull it into the cabin. Then,
connect it to the body wiring connector (B).
6. To install rear work lamp, open the cabin roof, secure the roof with a rod, and
x the rear work lamp (1) to the bracket (A) with the bolt (2), nut (4).
TG2A707C
8. Install the cabin roof.
A : Rear work lamp
B : Side work lamp
TG2A708A
TG2A709b
TG120_07_작업등키트_영문-A4.indd 4 2016-07-04 오전 8:34:32