Daewoo DSC-3270E User manual

TSC130BEF0
September

1

2

3
PIN Signal Designation Matching Value
1Audio Out (linked with 3) 0.5Vrms, Imp < 1 k (RF 60% MOD)
2Audio In (linked with 6) 0.5Vrms, Imp < 10 k
3Audio Out (linked with 1) 0.5Vrms, Imp < 1 k (RF 60% MOD)
4Audio Earth
5Blue Earth
6Audio in (linked with 2) 0.5Vrms, Imp < 10 k (RF 60% MOD)
7Blue in 0.7Vpp 2dB, Imp 75
8Slow (Function) Switching TV : 0-2V, PERI : 9.5 - 12V, Imp > 10 k
9Green Earth
10 NC
11 Green In 0.7Vpp 2dB, Imp 75
12 NC
13 Red Earth
14 Rapid(Blanking) Switching Earth
15 Red In, C In 0.7Vpp 2dB, Imp 75
16 Rapid(Blanking) switching Logic 0 : 0 - 0.4V, Logic 1 : 1 - 3V, Imp 75
17 Video Earth
18 Rapid Blanking Earth
19 Video Out 1Vpp 2dB, Imp 75
20 Video In, Y In 1Vpp 2dB, Imp 75
21 Common Earth
2. Specifications
+
-
+
-
+
-
+
-
+
-

4
3. Circuit Block Diagram

5
5. Alignment Instructions
4-1. User Remocon
RV-22D
TV..........................TXT
VOLUME........VOLUME
DOWN DOWN
(CURSOR
LEFT)
TV..............................TXT
MENU.................MENU
POWER...........POWER
PR.......................PAGE
NUMBER NUMBER
0-9 0-9
SLEEP............Not used
Not used.........CANCEL
Not used.............HOLD
RECALL.......SUBPAGE
STILL..............REVEAL
Not used.....................R
Not used....................G
PR UP...............PAGE UP
VOLUME UP .... VOLUME UP
(CURSOR
RIGHT)
NORMAL.................Not used
AV............................Not used
TXT...................................TV
SOUND MODE.......Not used
MUTE..........................MUTE
Not used........................SIZE
Not used........................SIZE
ZOOM.....................Not used
EFFECT..................Not used
Not used..............................C
Not used..............................Y

6

7

8
4-6-3 VERTICAL SIZE
* The VERTICAL CENTER adjustment has to be done in advance.
1) Apply a RETMA PATTERN Signal.
2) Set the TV to Normal I mode.
3) Adjust the VERTICAL SIZE of the picture with the select V.size by
volume UP/DOWN keys.
4-6-4 VERTICAL S-CORRECTION ( Fixed : Adjust if need be )
1) Apply a CROSSHATCH PATTERN Signal.
2) Adjust the S-CORRECTION to obtain the same distance between
horizontal lines with the S.Curve by volume UP/DOWN keys.
4-6-5 HORIZONTAL CENTER
1) Apply a RETMA PATTERN Signal.
2) Adjust picture centering with the select H.Center by volume UP/DOWN keys.
4-7. EW
4-7-1 WIDTH
1) Apply a RETMA PATTERN Signal.
2) Adjust the horizontal width to make a perfect circle with the select H.Width
by volume UP/DOWN keys.
4-7-2 PARA
1) Apply a CROSSHATCH PATTERN Signal.
2) Adjust the vertical line to straight with the select E.W Para by volume
UP/DOWN keys.
4-7-3 CORNER ( Fixed : Adjust if need be )
1) Apply a CROSSHATCH PATTERN Signal.
2) Adjust the vertical line to straight with the select EW.Cor T by volume
UP/DOWN keys.
4-7-4 SYMMETRY ( Fixed : Adjust if need be )
1) Apply a CROSSHATCH PATTERN Signal.
2) Turn R451 to the maximum left.
3) Adjust the symmetrical balance to be suitable with the select EW Sym by
volume UP/DOWN keys.
Alignment Instructions

9
4-8. WHITE BALANCE
4-8-1 RGB Reference R
4-8-2 Beam Reference LOW ( 288, 301 : 10Cd/ )
HIGH ( 288, 301 : 10Cd/ )
4-8-3 Adjust G, B Gain with select Menu G,B of BIAS, DRIVE of select Menu so that R, G, B Bars
are on the center position of the analog meter. If R Analog meter is not on center, control
the Brightness +/- of user Remocon so as R Analog meter to be on the center position.
4-9. SUB BRIGHT
4-9-1 Pattern : Retma
4-9-2 Adjust the SUB BRIGHT with the select Sub Bri by volume UP/DOWN keys.
so that only H-Center parts of picture can be seen.
4-10. DOUBLE TEXT CENTER
4-10-1 Pattern : Pattern RED
4-10-2 Select Menu
4-10-3 Select DT in SVC menu time to see the Double Text Picture.
( Left : RF Picture, Right : Text Picture )
4-10-4 Change the Double Text control keys volume UP/DOWN keys so that the left edge of text
picture concur with the right edge of RF picture.
Alignment Instructions
m
2
m
2