Daewoo DWF-800MP User manual

INSTRUCTION MANUAL Model: DWF-800MP
TABLE OF CONTENTS
■ SAFETY INSTRUCTION &
SPECIFICATIONS......................................2
■ PARTS DESCRIPTIONS............................3
■ DIRECTIONS FOR SAFE USE..................4
•How To Install............................................4
•Water Connection......................................6
•Drain Hose Setting....................................7
■ HOW TO OPERATE...................................8
•Preparation for Washing............................8
•Descriptions of Control Panel....................9
•General Procedures for Operation..........10
•Guides for Basic Washing Programs......11
•Partial Process of Combination...............13
■ PERIODIC MAINTENANCE.....................14
■
SPECIAL GUIDES FOR REMOVING STAINS
...16
■ TROUBLE SHOOTING GUIDES.............17
*
PLEASE READ CAREFULLY THIS INSTRUCTION
MANUAL BEFORE USING YOUR WASHER AND SAVE
THIS FOR FUTURE REFERENC
E.
DWF-800MP(¿ )01.3.269:57PM ˘`1

2
SAFETY INSTRUCTIONS & SPECIFICATIONS
SAFETY INSTRUCTIONS
❐ Your safety is important to us.
Read all instructions before using your washer.
SPECIFICATIONS
❐ The above specifications and features are subject to change without prior notice.
☞
Do not wash items cleaned, washed, soaked in, or spotted with wax, paint, gasoline, oil, or other
flammable fluids. The fumes can create a fire hazard or explosion.
☞
Flammable fluids (dry-cleaning solvents, kerosene, gasoline, etc.) should not be used or stored in or near
your washer. Do not add flammable fluids to your wash water. These substances give off vapors that can
create a fire hazard or explosion.
☞
Do not allow children to operate, play with, or crawl on or inside your washer.
Supervise children closely when your washer is used near them.
☞
Do not reach into the wash tub unless START/HOLD button is pressed and all motion stops, while spinning.
☞
Do not use chlorine bleach and ammonia or acids (such as vinegar or rust remover) in the same wash.
Hazardous fumes can form.
☞
Unplug power supply cord before attempting to service your washer.
☞
Do not pour water on the control panel.
☞
Remove foreign objects (such as coin, pin, knife, other metallic materials, etc.) inside your wash load.
They may damage any fabric.
☞
Do not overload your washer to avoid poor cleaning, wrinkling and/or any abnormal operation.
DWF-800MP
Please refer to the rating label at the back of your washer
320W
525X535
858
29
6.0kg
Anti-Rust Stainless Steel
Approx. 130 Liters/Cycle
Please refer to the rating label at the back of your washer.
4 Programs
High (55 Liters), Medium (45 Liters), Low (31 Liters)
Backward
0.3Kgf/cm
2
~8Kgf/cm
2
(2.94N/cm
2
~78.4N/cm
2
)
Provided with 6 Spouting Holes for Powerful Upward Water Stream
1. Air Bubble Generator
2. Reserved Washing with Display for remaining time
3. Signal Buzzer for the Operation of Control Button
Only in Pump Model identified with ‘P’ added to Model No.
MODEL NO
Power Source
Power Consumption
Width X Depth (mm)
Height (mm)
Net Weight (Kg)
Maximum Mass of Textile
Material of Internal Tub
Water Consumption
Washing Capacity
Washing Program
Water Level
Direction of Inlet Valve
Operating Water Pressure
Pulsator
Optional Features
Coin Filter
DWF-800MP(¿ )01.3.269:57PM ˘`2

3
PARTS DESCRIPTIONS
❐ The drawings in this book may vary from your washer model. They are designed to show the
different features of all models covered by this book. Your model may not include all features.
ACCESSORIES (Full Option)
Hose Adapter
Drain Hose
Under Cover
Inlet Hose
Hose Clamp
In case of screw-shaped inlet hoses
water tap adapters will not be provided.
UP
FABRIC SOFTNER INLET
(Symbol, See page 10)
DETERGENT CASE
(Symbol )
CONTROL PANEL
(88 display and some
buttons may be excluded)
WASH TUB
PULSATOR
LIQUID BLEACH INLET
(Symbol See page 10)
BASE
(Height is optional)
GROUND WIRE
(This will not be
provided in
case of 3-wire
power cord)
ADJUSTABLE LEG
(Optional)
WATER CONNECTOR
(Blue Color : Cold,
Pink Color : Hot)
PLUG
DRAIN HOSE
LINT FILTER
DOOR
DWF-800MP(¿ )01.3.269:57PM ˘`3

4
DIRECTIONS FOR SAFE USE
HOW TO INSTALL
Location
Place your washer on a level and solid floor,
Considering the length of inlet hose, drain
hose and power supply cord.
Do not place or store your washer below 0˚C(32˚F) to avoid
any damage from freezing.
Do not place your washer where it may be splashed during
bathing.
Installation of the Under Base Cover(Option)
After installing the washing machine,
assemble the under-base cover.
If washer is not level, it should be corrected by
the adjustable leg (provided optionally) in the
front-right side under the base and/or, a thin
block or brick.
NOTES:
The opening muse not be obstructed by carpeting
when the washing machine is installed on a
carpeted floor.
1
Before installing your washer, remove the
pad from the bottom of the cabinet. Then,
separate under cover from rear side of
cabinet by unscrewing and insert it into the
base.
2
Push the under-base cover into the end,
which decrease the noise made by this
washer.
SCREW
1
After the packing box is opened, there is a
under-base cover at the top of the washer. 2
Push the under-base cover into the end,
which decrease the noise made by this
washer.
DWF-800MP(¿ )01.3.269:57PM ˘`4

5
Power Supply
•Before plugging the plug into wall receptacle,
check the voltage rating is in the range of
rating, marked on the label at the back side of
your washer.
SCREW
Grounding
•If your water tap or water
pipe is not made of metal,
connect the ground wire to
a copper plate or a metal
rod and bury it in the earth.
•If both your water tap and
water pipe are made of
metal, connect the ground
wire to the base of the water
tap.
•It is of no use connecting the
ground wire to the water pipe
made of plastic.
•In case of using 3-core
cord, there is no need for
grounding.
Never Connect the Ground Wire to Such a Thing
•Never connect it to a gas pipe because of
danger of a explosion.
Gas Pipe
•Never connect it to a telephone wire or a
lightning rod because of os very dangerous
at a thunderbolt.
Telephone Wire
LABEL
20Cm
DWF-800MP(¿ )01.3.269:57PM ˘`5

6
1Pull down the collar of the
inlet hose to separate it from
the hose adapter.
4Remove the tape, and
screw connector B into
connector A tightly.
2Loosen the four screws
properly in fitting into water
tap.
5Connect the inlet hose to
the hose adapter, pulling
down the collar of hose end.
3 Fit the hose adapter into the water
tap and tighten the four screws
evenly while pushing up the
adapter so that the rubber packing
can stick to the water tap tightly.
6Connect the opposite end of
the hose to water inlet of
your washer tightly.
•Please check the rubber
packing is inside the hose
end.
TAPE
Connector B
Connector A
1Connect the inlet
hose to the
thread of water
tap or water pipe
by tightening.
2For the opposite
end, connect it
to water inlet as
the above
procedure 6.
Inlet Hose
Connector D Rubber
Packing
Connector C
WATER CONNECTION
Be careful not to confuse hot water inlet (pink color) and cold water inlet (blue color), if your
washer is provided with dual water inlets.
Also if you have only one water tap, connect the inlet hose with cold water inlet (blue color).
For normal tap
❐ In case that your washer is not provided with collar compartment, procedure 3and 5is
not necessary.
For Thread-Fitting Type
Leak Test
Turn on the water completely to check for any leakage. If any leakage, turn off the water, try
again as the above procedures.
For the special tap, call a qualified plumber for the installation.
Connector
ConnectorHose
connector A
connector B
TAPE
DWF-800MP(¿ )01.3.269:57PM ˘`6

Before operating your washer, install drain hose
properly.
First, connect the drain hose to the drain outlet at
the rear side of your washer, and then fasten it
tightly with the hose clamp.
Next, the other end of drain hose set as the below.
7
DRAIN HOSE SETTING
1Connect the drain hose
to the drain outlet at the
rear side of the washing
machine, and fasten it
tightly with the clamp
supplied.
3Hook the drain hose to the edge
of the tub, paying attention that
there are no bends or
constructions along the drain
hose.
Or, connect the drain hose to a
standpipe of a diameter greater
than that of the drain hose and
at a height of min. 70cm.
2Attach the hose
guide included in
the accessory kit,
to guide the drain
hose over the tub
or standpipe.
4Attach the hose guide included in the
accessory kit, to guide the drain hose over
the tub or standpipe.
PULL HOSE
THROUGH
FLEX HOSE
GUIDE
APART
55mm
Pump Model
1In case that it goes over a
door sill. Don’t let the height
of the drain hose exceed
20cm from the ground.
.
2In case of extending the
drain hose. Don’t let the
total length exceed 3m.
3Be careful that the end of
the drain hose is not
immersed in water.
20cm
3m
Non-Pump Model
NOTES:
1. Let the highest point of the drain hose be more than 1m above the floor. If not so, the water in the washer could
be drained during operation.
2. Be sure that the height of the drain hose must be less than 1.4m above the floor, If not so, the wart in the washer
could not drain.
3. The hose guide MUST be fitted to the drain hose. The drain hose should not extend more than 55mm from the
end of the hose guide. This is to prevent ‘SYPHONING’. If necessary the drain hose can be trimmed to length.
MUST be
ventilated
DWF-800MP(¿ )01.3.269:57PM ˘`7

8
HOSE TO OPERATE
PREPARATION FOR WASHING
To obtain the best washing results, you must operate your washer properly.
This section give you this important information.
•Close zippers, snaps, and hooks to avoid
snagging other items.
Remove pins, buckles, and other hard
objects to avoid scratching the washer
interior.
•Empty pockets and turn them inside out.
•Turn down cuffs and turn synthetic knits
out to avoid pilling.
•Tie strings and sashes so they will not
tangle.
•Treat spoats and stains.
(see “Special Guides for Removing
stains”on page)
Preparing clothes for washing
•Drop items into washer loosely. Items
should move easily through wash water
for best cleaning and wrinkle-free results.
•Load washer properly and select correct
load size setting.
Overloading and selecting a setting too
small for the wash load can:
- cause poor cleaning
- increase wrinkling
- create excessive lint
- wear out items faster (because of
pilling)
•Mix large and small items in each load.
Load evenly to maintain washer balance.
An off balance load can make the washer
vibrate during spin.
•Reduce wash time when using a small
load size setting. Loads with only a few
small items need less wash time.
•Use a large load size setting to reduce
wrinkling with permanent press clothes
and some synthetic knits. These items
should have more room to move in the
water than heavy items (towels, jeans)
Loading
•Separate heavily soiled items from, lightly soiled ones, even if they would normally be
washed together.
•Sperate dark colors from light colors, colorfast items from non-colorfast item.
Sorting
DWF-800MP(¿ )01.3.269:57PM ˘`8

9
DESCRIPTIONS OF CONTROL PANEL
Power Switch
•Press this button to turn the power ON or OFF.
Temperature Selector (Optional)
•If your washer is connected to two water taps for cold water and hot water, you
can select them. Without operation, cold water would be selected
automatically.
Water Level Selector
•This button is used to select the water level you want.
Reservation Button
•If you want to reserve the finishing time of washing, use this button.
As this button is pressed, digit in display increases by 1 hour at one press.
•If current time is 8:00 am and you expect washing will be completed around
5:00 pm, press this nine times in order to display ‘9’.
Control Button
•If you want to change wash time, rinse times, spin time, you must press this
button after selecting each process by the process button.
Also, this button can be used spin only.
Program Button
•With this button, you can create new programs by combinations of process.
Course Selector
•This button is used to select the washing course according to the type of wash
loads.
•Either Wool or Suit course is adopted to your Washing Machine.
Start/Hold
•With this button, you can make your washer proceed your program, or stop
temporarily. And you can also release the temporary stop by pressing this.
DWF-800MP
DWF-800MP(¿ )01.3.269:57PM ˘`9

10
GENERAL PROCEDURES FOR OPERATION
1. Add measured detergent to the washer, (Follow manufacture’s directions for safe use)
2. OPTIONAL STEP
If desired, add measured liquid chlorine bleach to the bleach inlet. use only liquid chlorine
in the bleach inlet
•Follow manufacturer’s direction for safe use.
3. OPTIONAL STEP
If desired, add measured liquid fabric softener to the softener inlet.
•Pour liquid fabric softener into the dispenser using the amount recommended on the
package. Avoid dripping or spilling any fabric softener on the load.
•The dispenser is for liquid fabric softener use only.
4. Close the washer lid (door)
5. Press the power button.
6. Select the course. The full automatic course has four settings; FUZZY, LIGHT, HEAVY,
WOOL. (See page 9)
7. Press the “START/HOLD”button.
Bleach inlet
(Symbol)
Softener inlet
(Symbol)
NOTES:
•Do not let bleach splash, drip, or run down into washer basket.
Undiluted bleach will damage any fabric it to touches.
•Do not use this dispenser to add powdered chlorine or color safe bleach to
your wash load. The dispenser is for liquid chlorine bleach use only.
DWF-800MP(¿ )01.3.269:58PM ˘`10

11
GUIDES FOR BASIC WASHING PROGRAMS
Fuzzy Course
•This course is a washing method for the general clothes except the extraordinary clothes
such as blanket, wool, etc.
1Put in the clothes. 2Press the power switch. 3Press the Start/Hold button,
and close the lid.
POWER START
/ HOLD
Heavy Program
•This selection is effective for blue-jean, climbing clothes, ruck sack, sports wear.
1Press the power
switch. 2Press the course selection button for
“HEAVY”
❍ FUZZY
● HEAVY
❍ SPEEDY
❍ WOOL
3Select the water
lever proper to the
wash load.
❍ HIGH
● MID
❍ LOW
4Press the
Start/Hold button,
and close the lid.
POWER
PROGRAM
WATER
LEVEL
START
/ HOLD
DWF-800MP(¿ )01.3.269:58PM ˘`11

12
Speedy Program
•This course is effective for the washing of light clothes or lightly stained clothes.
•Regulate the water level according to the wash load.
1Press the power
switch. 2Press the course selection button for
“SPEEDY”
❍ FUZZY
❍ HEAVY
● SPEEDY
❍ WOOL
3Select the water
lever proper to the
wash load.
❍ HIGH
● MID
❍ LOW
4Press the
Start/Hold button,
and close the lid.
POWER
PROGRAM
WATER
LEVEL
START
/ HOLD
Wool Course
•This selection is effective for wool clothes. (1.2kg’s limitation for 1-time wash)
•Do not put leather clothes, or chamois clothes into the washing tub for washing.
It may cause shrinkage or deformation to the clothes.
•Please use the neutral detergents only.
1Press the power
switch. 2Press the course selection button for
“WOOL”
❍ FUZZY
❍ HEAVY
❍ SPEEDY
● WOOL
3Select the water
lever proper to the
wash load.
❍ HIGH
● MID
❍ LOW
4Press the
Start/Hold button,
and close the lid.
POWER
PROGRAM
WATER
LEVEL
START
/ HOLD
DWF-800MP(¿ )01.3.269:58PM ˘`12

13
GUIDES FOR OTHER USEFUL PROGRAMS
Partial process & combination
For the reservation of finishing time
Convenient operation for spin only
1Set your program as the
above procedure, remaining
last step.
•Press the course selection
button.
•Press the procedure selection
button.
•But wool/suit course can not
reservation.
2Press reservation button
until the digital monitor
displays the finishing time
you want.
3Press Start/Hold to start.
•If you want spin only, it is convenient to operate the
button as following;
RES.
START
/ HOLD
WASH TIME CONTROL
•As the control button is pressed, wash time will be repeated as
following;
12 →15 → 18 →0 →6 →9 min
•If you don’t want wash process, you must adjust wash time to 8 min..
RINSE TIMES CONTROL
•As the control button is pressed, rinse times will be repeated as
following;
2 → 3 → 4 → 0 → 1 time(s)
•If you don’t want rinse process, you must adjust rinse times to 0
times.
SPIN TIME CONTROL
•As the control button is pressed, rinse times will be repeated as
following;
5 → 7 → 9 → 0 → 1 → 3 min.
•If you don’t want spin process, you must adjust spin time to 0 min..
DWF-800MP(¿ )01.3.269:58PM ˘`13

14
PERIODIC MAINTENANCE
Proper care of your washer can extend its life. This section explains how to care for your
washer properly and safely.
Cleaning your washer
Wipe up detergent, bleach, and other spills
with a soft, damp cloth or
sponge as they occur.
Occasionally wipe the
outside of the washer to
keep it looking like new.
Clean interior with 250ml of chlorine
bleach mixed with 500ml of detergent.
Run washer through a complete cycle.
Repeat process if necessary.
Exterior Interior
Do not put sharp or metal object in your washer, they
can damage the finish. Check all pockets for pins,
clips, money, bolts, nuts, etc.
Do not lay these objects on your washer after emptying
pockets.
Winter storage or moving care
Install and store your washer where it will not freeze. Because some water may stay in the
hoses, freezing can damage your washer.
If storing or moving your washer during freezing weather, winterize it.
Non-use or vacation care
Operate your washer only when you are at home.
If will be on vacation or not using your washer for an extended period of time, you should:
•Unplug the power supply cord or turn off electrical power to the washer.
•Turn off the water supply to the washer.
This helps avoid accidental flooding (due to a water pressure surge) while you are away.
•Shut off water faucet.
•Disconnect and drain water inlet hoses
•Run washer on a drain and spin
setting(see page 13) for 1 minute.
•Unplug the power supply cord.
•Flush water pipes and hoses.
•Recombination water inlet hoses.
•Turn on water faucet.
•Recombination power supply cord.
To winterize washer To use washer again
DWF-800MP(¿ )01.3.269:58PM ˘`14

15
Cleaning the Lint Filter
1Pull the Filter frame up
ward. 2Turn the lint filter inside out, wash to the lint off with
water.
3Return the filter as it was,
and insert the filter frame
into the slot
Filter Frame
Lint Filter
Cleaning the water inlet filter
•Clean the filter when water leaks form, the water inlet.
1Pull the power plug
out before cleaning
it.
2Turn off the water
supply to the washer
and sperate the inlet
hose.
3Pull the inlet filter
out. 4Remove the dirt from the inlet filter
with a brush.
Cleaning the drain filter
•In case “U”shape drain hose, this filter’s equipped at the cack side of washer.
•This drain filter is to screen the foreign stuffs such as threads, coins, pins, buttons etc...
•If the drain filter is not cleaned at proper time(every 10 times of use), Drain problem could
be caused, see page
1Put down the remained
water in the hose. And put a
container under the filter to
collect water.
4Clean the drain filter
removing the foreign stuffs.
2Turn the cap counter
clockwise.
5Put in the filter along the
guiding prominence of the
case. Please note the left
position of the filter adjusting
the groove to the guide rib.
3Pull out the filter assembly
off the case of the main
body.
6Turn the cap clockwise
tightly.
FILTER CONTAINER
CAP
SLIT
CASE
FILTER
CAP
CAP
CAP
FILTER CASE
GUIDE
RIB
SLIT
CAP
FILTER
DWF-800MP(¿ )01.3.269:58PM ˘`15

16
SPECIAL GUIDES FOR REMOVING STAINS
Stained, heavily-soiled, or greasy items, may need to be prewashed or soaked for best
results. Soaking helps remove protein-type stains like blood, milk, or grass. Prewashing
helps loosen soil before washing.
Stain removal rules
•Use warm water for soaking or prewashing stained laundry. Hot water can set stains.
•Most stains are easier to remove when they are fresh. Old or set stains may not coconut.
•Before treating any stain, find out what kind of stain it is, how old the stain is, what kind of
fabric it is, and if the fabric is colorfast.(Check the care label)
•Washing and drying can set some stains.
•Start with cold or warm water, hot water can set some stain.
•When bleach is recommended, use a bleach that is safe for the fabric.
•Put the stained area face down on a paper towel or white cloth. Apply the stain remover to
the back of the stain. This forces the stain off fabric instead of through it.
Stain removal guide
TO REMOVE
Rinse immediately in COLD water.
If stain remains, soak in cold water with an enzyme prewash.
Use ice in plastic bag to harden the gum.
Scrape off what you can and then sponge with white spirits.
Sponge with COLD water and soak in an enzyme prewash.
If stains persist, rub in a little detergent and rinse in cold water.
Blot up quickly and rinse out in COLD water.
Rub in a little detergent and wash in the maximum temperature allowed for the fabric type.
Rinse in COLD water and wash normally.
If stain is still apparent, sponge with white spirits.
Rub affected area with white vinegar and then rinse under running COLD water.
Sponge with white spirits.
Treat stiffened areas with enzyme prewash
Soak in a COLD enzyme prewash, rinse and wash normal.
Rub affected area with bar soap and wash normally.
Treat as soon as pressible by sponging with COLD water.
Rub a little detergent on the stain and wash normally.
Sponge with white sprites.
Rub a little detergent on the stain and wash normally.
Lay the affected area face down on an absorbent cloth and work from the back.
Sponge with white spirits or dry cleaning fluid. Wash normally.
Apply lemon juice and salt and place in the sun. Wash normally.
Sponge with white methylated spirits and wash normally.
Wash in WARM water and detergent.
Moisten area with lemon juice, dry in the sun and wash normally.
If stain persists and the fabric allows, use a bleach.
Brush off any dry mud. Rinse in cold water.
If stain persists rub in a little detergent and wash normally.
Scrape off any fresh paint and sponge with a non flammable dry cleaning fluid and wash
normally.
Treat while still wet, rinse in WARM water and wash normally.
Dampen a cloth with hydrogen peroxide, lay it over the affected area and press with a
fairly hot iron.
STAIN
Blood
Chewing gum
Cocoa, Chocolate
Coffee
Cream/Milk
Ice cream
Deodorant
Egg
Fabric/Softener
Fruit stains
Grass
Grease and oil
Iron or rust
Lipstick
Mildew
Mud
Paint-oil based
Pain-water based
Scorch marks
DWF-800MP(¿ )01.3.269:58PM ˘`16

17
TROUBLE SHOOTING GUIDES
Most problems are easily solved if you understand the cause. Check the following list for
problem before calling for service.
Before calling for service, check these
NOTES:
Please check the point before calling for a service.
If the supply cord is damaged, it must only be replaced by a repair shop appointed by manufacturer, because
special purpose tools are required.
•The washer will not operate at all.
•Water is not supplied;
If water supply is not finished within 30 minutes,
the lamp will light up, and the buzzer will
sound to indicate a problem.
•The washer will not drain;
If the drain is not finished within selected time, lamp
will light up, and the buzzer will sound to
indicate a problem.
•The washer will not spin;
If the clothes is collected on one side during spin and
the tub becomes unbalanced, the spin operation will
be interrupted, and then this unbalanced condition
will be corrected by following operation; WATER
SUPPLY ➡➡ Rinse ➡➡Drain However if the
unbalanced condition is unchanged despite repeating
the above operation, the lamp will light up, and
the buzzer will sound to indicate a problem.
•Is there a power failure?
•Is the power cord correctly connected to an
electric outlet?
•Is the electric fuse broken?
•Did you turn on the power?
•Did you press Start/Hold button?
•Is there correct amount of water in the tub?
•Did you connect the inlet hose and open the
water tap?
•Is the inlet hose or the water tap frozen?
•Is the water supply shut off?
•Does foreign matter block up the inlet hose
filter?
•Is the drain hose frozen or blocked up by dirt?
•Is the drain hose kinked or deformed?
•Is the end of the drain hose immersed in
water?
•Is there excessive dirt inside the pump
housing?
•Is the clothe in the tub collected on one side?
•Is the washing machine installed on an uneven
floor or is the vibration serious?
•Is the lid open?
(the lamp will light up in this case.)
PROBLEM CHECK POINT
• These cases are not malfunctions
•The sound “Wing”heard during water supply is the operating sound made by the water inlet valve.
•The sound “sha”heard in stopping the tub is the sound that comes from the autobalancer of the
tub.
•The sound “Wung”heard during washer or spin is the operating sound made by the air bubble
generator.
DWF-800MP(¿ )01.3.269:58PM ˘`17

VISION CREATIVE, INC.
`–‚‡†·º„fi•˛ 5¡526
·º¿ · ” ø 16 ˆ
·ª · TEL
MODEL DWF-803MNP
BUYER DWF-800MP(¿)
1´00.10.30 6´
2´7´
ˇ`⁄3´8´
4´9´
5´10 ´
`ƒ˘˙ ˙(2000.10.31)
¿ ˛˛…… ‚µ ¿¿ ¿ ˇˇ
–
MEMO
¿¿‹‹¶¶ Ù ˆˆ‡‡
VVIISSIIOONN
··ªª·· Á
`˙
TEL: [phone] FAX: [phone]
DWF-800MP(¿)01.3.269:58PM˘`18