Dahua VTO2111D-WP Parts list manual

Intercom Setup
VTH status indicator key:
Prerequisites
Power to the monitor and outdoor station (PoE or DC12V)
Wired or wireless network
Windows PC on the network

Step by Step Instructions
Below are several sets of instructions for setting up both the VTO and VTH system in their
respective interfaces.
Wired Instructions
Follow the instructions below for using a wired network (or PoE).
Video Instructions: VTO
VTO2111D-WP
1. Please plug in the appropriate power supply, the VTO2111D-WP can use PoE or a DC
power supply:
PoE:

DC power supply:
2. For this exercise, the VTO will have both DC power and a direct Ethernet connection
directly to a laptop for setup. After the unit has booted up make sure you have a network
connection to the device via an Ethernet cable.

3. If you are using a direct connection please set your devices IP address to 192.168.1.x
(x=any available IP), subnet mask 255.255.255.0. This will ensure you are using the same
IP scheme as the VTO's factory defaults.
4. Launch Internet Explorer and enter the VTO's default IP address into the URL address
bar: 192.168.1.110. If you cannot see the web page load on this default IP, then please press
and hold the reset button located on the back side of the VTO for 15 seconds while the
device is powered on. Once at the login page please enter the default username (admin) and
password (admin).

5. After the login page please select Network Config on the left side. Under the TCP/IP tab
please input the desired network configuration. For this exercise, the network uses a
192.168.2.x scheme, and the device will be configured on the wired interface (Eth0) and on
a static IP address on the LAN (DCHP-Off). After the settings have been entered, select OK.
Changing network schemes will disconnect the device when directly connected. From here
the device can now be plugged into the network, and accessed from the network.
6. To configure the Main VTH with the VTO we will need to add the VTH's room number (or
desired room number) to the VTO. Select Indoor Manager on the left, select Add, from here
the only necessary info will be the room number. For this example we will be using 9902 as
the Main VTH's room number, select OK when this is finished. *Note* The VTO's room
number can differ from this number (default of 6901), however this specific device can only
add one Main VTH (with multiple VTH extensions).
7. From here the VTO will use an auto negotiation protocol with the VTH. This process will
sometimes require rebooting the device. To access the software reboot on the VTO please
select Logout on the left side -> Reboot Device -> Reboot Device, and wait 2-5 minutes.

Please follow the second part of the Step by Step instructions to setup and configure the
VTH5221D
Video Instructions: VTH
VTH5221D
1. Please plug in the appropriate power supply, the VTH5221D can use PoE or a DC power
supply:
PoE:
DC power supply:

2. Once the VTH has booted up please tap the screen to wake up the main menu.
Press and hold Setting until a login menu appears on the screen.
Tap the area next to Password: and enter 888888 to get into the main settings of the device.

3. At the Network area of the VTH tap Wired IP.

4. Here you can set a static LAN IP, then select OK.
Alternatively you can use DHCP to grab an address from your Routers DHCP server, then
select OK.

5. To setup the Room No. tap the field and enter a four digit room number (or the number
that had been added on the VTO) then select OK.

6. Tap VTO Set on the left and enter the VTO IP Address, username, and password that you
configured in the VTO setup process.
Then Enable Status to ON.

Note:If the VTO not Connected symbol in the upper right corner does not go away, then you
will need to reboot the device through Setting -> Reboot. If this does not work repeat this
step. If that does not work, reboot the VTO and repeat this step.
7. Once the VTO not Connected status is cleared, attempt to make a call from the VTO by
pressing the blue door bell button.

Wireless
Follow the instructions below for using a wireless network.
Video Instructions: VTO
VTO2111D-WP
1. Please plug in the appropriate power supply, since the VTO2111D-WP can use PoE or a
DC power supply:
PoE:

DC power supply:
2. For this exercise, the VTO will have both DC power and a direct Ethernet connection
directly to a laptop for setup. After the unit has booted up make sure you have a network
connection to the device via an Ethernet cable.

3. If you are using a direct connection please set your devices IP address to 192.168.1.x
(x=any available IP), subnet mask 255.255.255.0. This will ensure you are using the same
IP scheme as the VTO's factory defaults.

4. Launch Internet Explorer and enter the VTO's default IP address into the URL address
bar: 192.168.1.110. If you cannot see the web page load on this default IP, then please press
and hold the reset button located on the back side of the VTO for 15 seconds while the
device is powered on. Once at the login page please enter the default username (admin) and
password (admin).
5. After the login page please select Network Config on the left side. Under the TCP/IP tab
please input the desired network configuration under ETH2, which is the wifi interface. For
this exercise, the network uses a 192.168.2.x scheme, and the device will be configured on

the wireless interface (Eth2) and on a static IP address on the LAN (DCHP-Off). After the
settings have been entered, select OK.
6. Now select WIFI Info on the left hand side then select Open WLAN and wait while the
device scans for wifi networks in the area.
7. Once you have located your wireless network's name, select the + to connect. Enter in
your password for the network and then select OK to proceed connecting. Note: The
wireless network must operate on a 2.4GHz band for this device.

8. Once connected the State should list "Connected" on your designated network. You are
now connected via wifi, however the current connection to the network will disconnect,
please use the new IP address setup to connect to the VTO. From here the device can now
be unplugged from the wired network.
9. To configure the Main VTH with the VTO we will need to add the VTH's room number (or
desired room number) to the VTO. Select Indoor Manager on the left, select Add, from here
the only necessary info will be the room number. For this example we will be using 9902 as
the Main VTH's room number, select OK when this is finished. *Note* The VTO's room
number can differ from this number (default of 6901), however this specific device can only
add one Main VTH (with multiple VTH extensions).

10. From here the VTO will use an auto negotiation protocol with the VTH. This process will
sometimes require rebooting the device. To access the software reboot on the VTO please
select Logout on the left side -> Reboot Device -> Reboot Device, and wait 2-5 minutes.
Please follow the second part of the Step by Step instructions to setup and configure the
VTH5221D
Video Instructions: VTH
VTH5221D
1. Please plug in the appropriate power supply, the VTH5221D can use PoE or a DC power
supply:
PoE:

DC power supply:
2. Once the VTH has booted up please tap the screen to wake up the main menu.
Press and hold Setting until a login menu appears on the screen.

Tap the area next to Password: and enter 888888 to get into the main settings of the device.